Eizo FlexScan S1503 User manual

Important
Please read PRECAUTIONS, this User’s Manual, and the Setup Guide
(separate volume) carefully to familiarize yourself with safe and
effective usage.
• Please refer to the Setup Guide for basic information ranging from
connection of the monitor to a PC to using the monitor.
• The latest User’s Manual is available for download from our web site:
http://www.eizo.com
Cover

2
Location of Caution Statement
This product has been adjusted specically for use in the region to which it was originally shipped. If operated
outside this region, the product may not perform as stated in the specications.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means,
electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.
EIZO Corporation is under no obligation to hold any submitted material or information condential unless prior
arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although every effort has been
made to ensure that this manual provides up-to-date information, please note that EIZO monitor specications are
subject to change without notice.

3
Noticeforthismonitor
Notice for this monitor
This product is suited to general purposes like creating documents, viewing multimedia content.
This product has been adjusted specically for use in the region to which it was originally shipped. If the product is
used outside the region, it may not operate as specied in the specications.
This product may not be covered by warranty for uses other than those described in this manual.
The specications noted in this manual are only applicable when the following are used:
· Power cords provided with the product
· Signal cables specied by us
Only use optional products manufactured or specied by us with this product.
It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more after the
monitor power has been turned on, and then adjust the monitor.
Monitors should be set to a lower brightness to reduce changes in luminosity caused by long-term use and maintain a
stable display.
When the screen image is changed after displaying the same image for extended periods of time, an afterimage may
appear. Use the screen saver or power save function to avoid displaying the same image for extended periods of time.
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime (refer to
“Cleaning” (page 4)).
The LCD panel is manufactured using high-precision technology. Although, missing pixels or lit pixels may appear on
the LCD panel, this is not a malfunction. Percentage of effective dots: 99.9994% or higher.
The backlight of the LCD panel has a xed lifetime. When the screen becomes dark or begins to icker, please contact
your local EIZO representative.
Do not press on the panel or edge of the frame strongly, as this may result in display malfunctions, such as interference
patterns, etc. If pressure is continually applied to the panel, it may deteriorate or damage your panel. (If the pressure
marks remain on the panel, leave the monitor with a black or white screen. The symptom may disappear.)
Do not scratch or press on the panel with any sharp objects, as this may result in damage to the panel. Do not attempt
to brush with tissues as this may scratch the panel.
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew condensation may
occur on the interior and exterior surfaces of the monitor. In that case, do not turn the monitor on. Instead wait until
the dew condensation disappears, otherwise it may cause some damage to the monitor.

4Noticeforthismonitor
Cleaning
Attention
• Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet or panel,
and also quality deterioration of the image.
• Never use any thinner, benzene, wax, and abrasive cleaner, which may damage the cabinet or panel.
Note
• The optional ScreenCleaner is recommended for cleaning the cabinet and panel surface.
The stains on the cabinet and panel surface can be removed by moistening part of a soft cloth with water.
To use the monitor comfortably
• An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor according to
the environmental conditions.
• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.

5
CONTENTS
CONTENTS
Cover ...................................................................... 1
Notice for this monitor ......................................... 3
Cleaning .................................................................... 4
To use the monitor comfortably ............................. 4
CONTENTS ............................................................. 5
Chapter 1 Introduction ....................................... 6
1-1. Features ......................................................... 6
1-2. Controls and Functions ............................... 7
1-3. EIZO LCD Utility Disk.................................... 8
●Diskcontentsandsoftwareoverview............. 8
1-4. Basic Operations and Functions ................ 9
●BasicAdjustmentmenuoperations................ 9
●Functions........................................................10
Chapter 2 Adjusting Screens .......................... 11
2-1. Compatible Resolutions .............................11
●AnalogInput(D-Sub).....................................11
●DigitalInput(DVI-D).......................................11
2-2. Setting the Resolution ................................12
●Windows7......................................................12
●WindowsVista................................................12
●WindowsXP...................................................12
●MacOSX.......................................................12
2-3. Displaying Screen Correctly.......................13
●DigitalSignalInput.........................................13
●AnalogSignalInput........................................13
2-4. Adjusting Color ............................................17
●Toselectthedisplaymode(ColorMode).......17
●Toperformadvancedadjustments................17
●Adjustablesettingsineachmode..................17
●Toadjustbrightness<Brightness>................18
●Toadjustcontrast<Contrast>........................18
●Toadjustcolortemperature<Temperature>..19
●Toadjustgain<Gain>....................................19
Chapter 3 Setting Monitor ............................... 20
3-1. Adjusting Volume “Volume” ...................... 20
3-2. Changing Adjustment Menu Display
Position <Menu Position> .......................... 20
3-3. Locking Buttons .......................................... 20
3-4. Setting the EIZO Logo Display .................. 20
3-5. Setting Language <Language> ..................21
3-6. Enabling/Disabling DDC/CI
communication ............................................21
3-7. Resetting the Monitor to the Default
Settings <Reset> ..........................................21
●Toresetthecoloradjustments.......................21
●Toresetalladjustmentstothedefault
settings.......................................................... 22
Chapter 4 Power Saving Functions ................ 23
4-1. Power Saving Mode .................................... 23
4-2. Setting Power Indicator <Power
Indicator> ..................................................... 23
4-3. Enabling/Disabling Automatic
Brightness Adjustment “Auto EcoView” . 24
4-4. Setting Indicator “EcoView Index” ........... 24
4-5. Enabling/Disabling Auto Power-OFF
<Eco Timer> ................................................ 24
Chapter 5 Troubleshooting .............................. 25
5-1. No picture .................................................... 25
5-2. Imaging problems (for both digital and
analog) .......................................................... 26
5-3. Imaging problems (for analog only) ......... 26
5-4. Other problems ........................................... 27
Chapter 6 Reference ........................................ 28
6-1. How to Attach the Optional Arm ............... 28
6-2. Connecting Multiple PCs ........................... 29
●Toswitchamonginputsignals...................... 29
●Tosetinputsignalselection<InputSignal>. 30
6-3. Displaying Monitor Information
<Information> .............................................. 30
6-4. Specications ..............................................31
6-5. Preset Timing .............................................. 33
Chapter 7 Glossary .......................................... 34
Appendix .............................................................. 36
Trademark ............................................................... 36
FCC Declaration of Conformity .............................37
Hinweise zur Auswahl des richtigen
Schwenkarms für Ihren Monitor ..................... 38
Hinweis zur Ergonomie : ....................................... 38
LIMITED WARRANTY ............................................. 39
Recycling Information ........................................... 48
China Measures for RoHS Compliance in
ChinaRoHS ........................................................ 52

6Chapter1Introduction
Chapter 1 Introduction
Thank you very much for choosing an EIZO color LCD monitor.
1-1. Features
• 15” LCD
• Applicable to the resolution of 1024 × 768.
• LED backlight LCD panel
The LED backlight provides better power efciency and reduced power consumption compared to existing uorescent
backlight LCD panels. No mercury, a hazardous substance, is used.
• The software “ScreenManager Pro for LCD (DDC/CI)” to adjust the screen using the mouse and keyboard
is included
See “1-3. EIZO LCD Utility Disk” (page 8).
• Supports the power management software “EIZO EcoView NET”
For more information, refer to our web site (http://www.eizo.com).
• Power saving function
Suppressing the power consumption reduces the carbon dioxide emissions. This product is equipped with power
saving function.
- 0 W power consumption when the main power is off
Equipped with main power switch.
When the monitor is not required, the power supply can be shut off using the main power switch.
- Auto EcoView
The ambient light sensor on the front side of the monitor detects the environmental brightness to adjust the screen
brightness automatically and comfortably. Excessively high brightness may increase power consumption and cause
unwanted environmental effects. It may also lead to fatigue of your eyes. Use the Auto EcoView to reduce the
brightness.
See “4-3. Enabling/Disabling Automatic Brightness Adjustment “Auto EcoView”” (page 24).
- EcoView Index
This indicator shows the power saving ratio, power reduction and CO2 reduction as a result of the brightness
of the monitor. You can realize the power consumption reduction by taking consideration in the ratio of power
saving.
See “4-4. Setting Indicator “EcoView Index”” (page 24).
• Displays HDCP (High-bandwidth Digital Protection) protected contents.

7
Chapter1Introduction
1-2. Controls and Functions
14
71 2 3 4 5 6 8 9 10 11 12 13 9
1 Sensor Thesensordetectsambientbrightness.AutoEcoViewfunction(page24)
2 EcoView button DisplaysthesettingmenuofAutoEcoViewandEcoViewIndex(page24).
3 Volume control button Displaysthevolumeadjustmentmenu(page20).
4
Input Signal Selection button Switchesinputsignalsfordisplay.
5 Enter button DisplaystheAdjustmentmenu,determinesanitemonthemenuscreen,and
savesvaluesadjusted.
6 Control buttons (Left, Right) •Displaysthebrightnessadjustmentwindow(page18).
•Choosesanadjustmentitemorincreases/decreasesadjustedvaluesfor
advancedadjustmentsusingtheAdjustmentmenu(page9).
7 Power button Turnsthepoweronoroff.
8 Power indicator Indicatesmonitor’soperationstatus.
Blue:OperatingOrange:PowersavingOff:Poweroff
9Speaker Outputsaudiosource.
10 Main power switch Turnsthemainpoweronoroff.
11
Power connector Connectsthepowercord.
12
Input signal connectors Left:DVI-Dconnector/Right:D-Submini15-pinconnector
13 Stereo mini jack Connectsthestereominijackcable.
14 Stand*2Usedtoadjusttheangleofthemonitorscreen.
*1ScreenManagerisanEIZO’snicknameoftheAdjustmentmenu.See“1-4.BasicOperationsandFunctions”(page9)
forhowtouse.
*2Anoptionalarm(oranoptionalstand)canbeattachedbyremovingthestandsection.(Referto“6-1.HowtoAttach
theOptionalArm”(page28))
Adjustmentmenu
(ScreenManager*1)

8Chapter1Introduction
1-3. EIZO LCD Utility Disk
An “EIZO LCD Utility Disk” (CD-ROM) is supplied with this product. The following table shows the disk
contents and the overview of the software programs.
● Disk contents and software overview
The disk includes software programs for adjustment, and User’s Manual. Refer to Readme.txt le on the disk
for software startup procedures or le access procedures.
Item Overview Windows Macintosh
Screenadjustmentpatternles Usedwhenadjustingtheimageofanalog
signalinputmanually. √ √
ScreenManagerProforLCD
(DDC/CI)
Softwareforadjustingthescreenusing
themouseandkeyboard. √ -
EIZOScreenSlicer Softwarethatdividesascreenandlays
outmultiplewindowsefciently. √ -
User’sManualofthismonitor(PDFle) √ √
Readme.txtle √ √

9
Chapter1Introduction
1-4. Basic Operations and Functions
● Basic Adjustment menu operations
1. Displaying Adjustment Menu
1. Press . The adjustment menu appears.
Atdigitalsignalinput
2.
Adjusting/Setting
1. Choose a menu to adjust/set with or , and then press . The Sub menu appears.
2. Choose an item to adjust/set with or , and then press . The adjustment/ setting menu appears.
3. Adjust/set the selected item with or , and then press .
3.
Exiting
1. Choose <Return> from the Sub menu and press . The Main menu appears.
2. Choose <Exit> from the Main menu and press . The Adjustment menu exits.
Note
• The Adjustment menu can also be exited by pressing twice quickly.

10 Chapter1Introduction
● Functions
The following table shows all the Adjustment menu’s adjustment and setting menus.
Main menu Setting Reference
AutoAdjustment*1 Screen “2-3.DisplayingScreenCorrectly”
(page13)
Range
Screen Clock*1
Phase*1
Hor.Position*1
Ver.Position*1
Smoothing
Return
Color*2 Brightness “2-4.AdjustingColor”(page17)
ColorMode
Contrast
Temperature
Gain
Reset “Toresetthecoloradjustments”
(page21)
Others InputSignal “Tosetinputsignalselection<Input
Signal>”(page30)
EcoTimer “4-5.Enabling/DisablingAuto
Power-OFF<EcoTimer>”(page24)
MenuPosition “3-2.ChangingAdjustmentMenu
DisplayPosition<MenuPosition>”
(page20)
PowerIndicator “4-2.SettingPowerIndicator
<PowerIndicator>”(page23)
Reset “Toresetalladjustmentstothe
defaultsettings”(page22)
Information “6-3.DisplayingMonitorInformation
<Information>”(page30)
Language “3-5.SettingLanguage
<Language>”(page21)
*1Analogsignalinputonly
*2Theadjustment/settingsavailableonthe<Color>menudependontheselectedColorMode(see
“Adjustablesettingsineachmode”(page17)).

11
Chapter2AdjustingScreens
Chapter 2 Adjusting Screens
2-1. Compatible Resolutions
The monitor supports the following resolutions.
● Analog Input (D-Sub)
Resolution Applicable Signals Vertical Scan
Frequency Dot Clock
640×480 VGA,VESA ~75Hz
80MHz
(Max.)
720×400 VGATEXT 70Hz
800×600 VESA ~75Hz
1024×768*1 VESA ~75Hz
● Digital Input (DVI-D)
Resolution Applicable Signals Vertical Scan
Frequency Dot Clock
640×480 VGA 60Hz
65MHz
(Max.)
720×400 VGATEXT 70Hz
800×600 VESA 60Hz
1024×768*1 VESA 60Hz
ThegraphicsboardshouldcomplywiththeVESAstandard.
*1Recommendedresolution

12 Chapter2AdjustingScreens
2-2. Setting the Resolution
When you connect the monitor to the PC and nd that the resolution is improper, or when you want to change
the resolution, follow the procedure below.
● Windows 8 / Windows 7
1. For Windows 8, click the “Desktop” tile on the Start Screen to display the desktop.
2. Right-click the mouse anywhere on the desktop except for icons.
3. From the displayed menu, click “Screen resolution”.
4. On the “Screen Resolution” dialog box, select the monitor.
5. Click “Resolution” to select the desired resolution.
6. Click the “OK” button.
7. When a conrmation dialog box is displayed, click [Keep changes].
● Windows Vista
1. Right-click the mouse anywhere on the desktop except for icons.
2. From the displayed menu, click “Personalize”.
3. On the “Personalization” window, click “Display Settings”.
4. On the “Display Settings” dialog box, select the “Monitor” tab and select desired resolution in the
“Resolution” eld.
5. Click the “OK” button.
6. When a conrmation dialog box is displayed, click “Yes”.
● Windows XP
1. Right-click the mouse anywhere on the desktop except for icons.
2. From the displayed menu, click “Properties”.
3. When the “Display Properties” dialog box is displayed, click the “Settings” tab and select desired
resolution for “Screen resolution” under “Display”.
4. Click the “OK” button to close the dialog box.
● Mac OS X
1. Select “System Preferences” from the Apple menu.
2. When the “System Preferences” dialog box is displayed, click “Displays” for “Hardware”.
3. On the displayed dialog box, select the “Display” tab and select desired resolution in the “Resolutions”
eld.
4. Your selection will be reected immediately. When you are satised with the selected resolution, close
the window.

13
Chapter2AdjustingScreens
2-3. Displaying Screen Correctly
● Digital Signal Input
When digital signals are input, images are displayed correctly based on the preset data of the monitor, but if
characters and/or lines appear blurred, go to “6. Modify blurred characters or lines.” (page 16).
When performing more advanced adjustment, see “2-4. Adjusting Color” (page 17) and subsequent pages.
● Analog Signal Input
Attention
• The monitor will take about 30 minutes before its internal electric components stabilize. Wait 30 minutes or more
after turning the monitor power on before starting adjustment.
• The self adjustment function does not work for the images under the vertical resolution of 480 or less.
• The self adjustment and auto adjustment functions work correctly when an image is fully displayed over the
Windows or Macintosh display area. They do not work properly in the cases below:
- When an image is displayed only on a part of the screen (command prompt window, for example)
- When a black background (wallpaper, etc.) is in use
Also, these functions cannot work properly in some graphic boards.
The monitor screen adjustment is used to suppress ickering of the screen or adjust screen position and
screen size correctly according to the PC to be used.
Note
• The self adjustment function works when all of the following conditions are satised:
- When a signal is input into the monitor for the rst time or when a resolution or vertical/horizontal scan frequency
not used before is set
If the screen is not displayed correctly even after performing the self adjustment operation, adjust the screen
according to the procedures on the following pages to use the monitor comfortably.
Setting Procedures
1. Perform the auto adjustment.
● To adjust ickering, screen position, and screen size automatically <Screen>
Procedure
1. Choose <Auto Adjustment> from the Adjustment menu, and press .
2. Choose <Screen> from the <Auto Adjustment> menu, and press .
The <Auto Adjustment> menu appears.
3. Select <Execute> with or , and press .
Flickering, screen position, and screen size are corrected by the auto-adjustment function.
Ifthescreenisnotdisplayedcorrectlyevenafterperforming“1.Performtheautoadjustment.”(page13),
performtheadjustmentsaccordingtotheproceduresonthefollowingpages.Ifthescreenisdisplayed
correctly,goto“5.Adjustingcolorgradation.”(page16).

14 Chapter2AdjustingScreens
2.
Prepare to use analog screen adjustment patterns.
Load the “EIZO LCD Utility Disk” to your PC, and then open the “Screen adjustment pattern les”.
Note
• For details and instructions on opening the “Screen adjustment pattern les”, refer to the Readme.txt le.
3.
Perform the auto adjustment again with the analog screen adjustment pattern
displayed.
● To adjust ickering, screen position, and screen size automatically <Screen>
Procedure
1. Display Pattern 1 in full screen on the monitor using the “Screen adjustment pattern les”.
2. Choose <Auto Adjustment> from the Adjustment menu, and press .
3. Choose <Screen> from the <Auto Adjustment> menu, and press .
The <Auto Adjustment> menu appears.
4. Select <Execute> with or , and press .
Flickering, screen position, and screen size are corrected by the auto-adjustment function.
Ifthescreenisnotdisplayedcorrectlyevenafterperforming“3.Performtheautoadjustmentagain
withtheanalogscreenadjustmentpatterndisplayed.”(page14),performtheadjustmentsaccordingto
theproceduresonthefollowingpages.Ifthescreenisdisplayedcorrectly,goto“5.Adjustingcolor
gradation.”(page16).
4.
Choose <Screen> from the Adjustment menu to perform advanced
adjustments.
Adjust the clock, phase and position, in this order.
● To eliminate vertical bars <Clock>
Procedure
1. Choose <Clock> from the <Screen> menu, and press .
The <Clock> menu appears.
2. Adjust the clock with or to eliminate vertical bars.
Press or slowly so as not to miss the adjustment point.
3. Press to exit the adjustment.
When blurring, ickering or bars appear on the screen after adjustment, proceed to “Phase” to remove ickering or
blurring.

15
Chapter2AdjustingScreens
● To remove ickering or blurring <Phase>
Procedure
1. Choose <Phase> from the <Screen> menu, and press .
The <Phase> menu appears.
2. Adjust the phase with or to minimize ickering or blurring.
3. Press to exit the adjustment.
When vertical bars appear on the screen after adjustment, go back to “To eliminate vertical bars <Clock>”.
(Clock → Phase → Position)
Attention
• Flickering or blurring may not be eliminated depending on your PC or graphics board.
● To correct the screen position <Hor.Position> <Ver.Position>
Note
• Since the number of pixels and the pixel positions are xed on the LCD monitor, only one position is provided to
display images correctly. The position adjustment is made to shift an image to the correct position.
Procedure
1. Choose <Hor.Position> or <Ver.Position> from the <Screen> menu, and press .
The <Hor.Position> or <Ver.Position> menu appears.
2. Adjust the position with or .
3. Press to exit the adjustment.
4. Close Pattern 1.

16 Chapter2AdjustingScreens
5.
Adjusting color gradation.
● To adjust color gradation automatically <Range>
Every color gradation (0 to 255) can be displayed by adjusting the signal output level.
Procedure
1. Display Pattern 2 in full screen on the monitor using the “Screen adjustment pattern les”.
2. Choose <Auto Adjustment> from the Adjustment menu, and press .
3. Choose <Range> from the <Auto Adjustment> menu, and press .
The <Range> menu appears.
4. Select <Execute> with or , and press .
The output range is set automatically.
5. Close Pattern 2.
6.
Modify blurred characters or lines.
● To modify blurred characters/lines <Smoothing>
When an image is displayed with a resolution other than recommended, the characters or lines of the
displayed image may blur.
Attention
• Smoothing setting may not be required depending on the display resolution. (You cannot choose the smoothing icon.)
Adjustable range
1 to 5
Procedure
1. Choose <Screen> from the Adjustment menu, and press .
2. Choose <Smoothing> from the <Screen> menu, and press .
The <Smoothing> menu appears.
3. Use or for adjustment.
4. Press to exit the adjustment.

17
Chapter2AdjustingScreens
2-4. Adjusting Color
● To select the display mode (Color Mode)
This function allows easy selection of a desired mode according to monitor application.
Display Modes
Mode Purpose
Custom Selectoneoftheseusermodestodeneadesiredsetofparametersettings.
EyeCare Allowsthebrightnesstobesetlowerthanpossiblewithothermodes.
sRGB SuitableforcolormatchingwithsRGBcompatibleperipherals.
Text Suitablefordisplayingtextsforwordprocessingorspreadsheets.
Procedure
1. Choose <Color> from the Adjustment menu, and press .
2. Choose <Color Mode> from the <Color> menu, and press .
3. Use or for adjustment.
4. Press to exit the adjustment.
● To perform advanced adjustments
The <Color> menu of the Adjustment menu allows you to congure and save a separate set of color settings
for each mode.
Attention
• The monitor will take about 30 minutes before its internal electric components stabilize. Wait 30 minutes or more
after turning the monitor power on before starting adjustment.
• Perform the range adjustment rst when adjusting color for analog signals (see “To adjust color gradation
automatically <Range>” (page 16)).
• The same image may be seen in different colors on multiple monitors due to their monitor-specic characteristics.
Make ne color adjustment visually when matching colors on multiple monitors.
Note
• The values shown in “%” or “K” are available only as reference.
● Adjustable settings in each mode
The adjustable settings depend on the mode. (You cannot select any non-adjustable or non-settable function.)
√: Adjustable -: Not adjustable
Icon Function Color Mode
Custom EyeCare sRGB Text
Brightness √√√√
Contrast √ - - √
Temperature √ √ - √
Gain √ √ - -
Reset √√√√

18 Chapter2AdjustingScreens
● To adjust brightness <Brightness>
The screen brightness is adjusted by changing the brightness of the backlight (light source from the LCD
back panel).
Adjustable range
0 to 100%
Procedure
1. Press or .
The Brightness menu appears.
2. Use or for adjustment.
3. Press to exit the adjustment.
Note
• If you feel that the image is too dark even if the brightness is set to 100%, adjust the contrast.
• Alternatively, you can use <Brightness> under <Color> in the Adjustment menu to adjust it.
● To adjust contrast <Contrast>
The brightness of the screen is adjusted by varying the video signal level.
Adjustable range
0 to 100%
Procedure
1. Choose <Color> from the Adjustment menu, and press .
2. Choose <Contrast> from the <Color> menu, and press .
The <Contrast> menu appears.
3. Use or for adjustment.
4. Press to exit the adjustment.
Note
• In the contrast of 50%, every color gradation is displayed.
• When adjusting the monitor, it is recommended to perform the brightness adjustment which may not lose the
gradation characteristics, prior to the contrast adjustment.
• Perform the contrast adjustment in the following cases.
- When you feel the image is too dark even if the brightness is set to 100% (Set the contrast to higher than 50%.)

19
Chapter2AdjustingScreens
● To adjust color temperature <Temperature>
Color temperature can be adjusted.
The color temperature is normally used to express the hue of “White” and/or “Black” by a numerical value.
The value is expressed in degrees “K” (Kelvin).
The screen becomes reddish at a low color temperature, and bluish at a high color temperature, like the ame
temperature. A gain preset value is set for each color temperature setting value.
Adjustable range
Off, 5000K, 6500K, 9300K
Procedure
1. Choose <Color> from the Adjustment menu, and press .
2. Choose <Temperature> from the <Color> menu, and press .
The <Temperature> menu appears.
3. Use or for adjustment.
4. Press to exit the adjustment.
Note
• <Gain> allows you to perform more advanced adjustment (see “To adjust gain <Gain>” (page 19)).
• If you set to “Off”, the image is displayed in the preset color of the monitor (Gain: 100% for each RGB).
• When gain is changed, the color temperature is changed to “Off”.
● To adjust gain <Gain>
The brightness of each color component red, green, and blue is called “Gain”. You can change the hue of
“white” by adjusting gain.
Adjustable range
0 to 100%
Procedure
1. Choose <Color> from the Adjustment menu, and press .
2. Choose <Gain> from the <Color> menu, and press .
The <Gain> menu appears.
3. Adjust gain with or for each of red, green, and blue.
4. Press to exit the adjustment.
Attention
• Using this function may make some color gradations unavailable for display.
Note
• The value of gain changes with that of color temperature.
• When gain is changed, the color temperature is changed to “Off”.

20 Chapter3SettingMonitor
Chapter 3 Setting Monitor
3-1. Adjusting Volume “Volume”
This function allows you to adjust the volume.
Adjustable range
0 to 20
Procedure
1. Press .
The sound volume menu appears.
2. Use or for adjustment.
3. Press to exit the adjustment.
3-2. Changing Adjustment Menu Display Position
<Menu Position>
You can change the display position of the Adjustment menu.
Procedure
1. Choose <Others> from the Adjustment menu, and press .
2. Choose <Menu Position> from the <Others> menu, and press .
The <Menu Position> menu appears.
3. Adjust the position with or .
4. Press to exit the adjustment.
3-3. Locking Buttons
This function allows you to lock to prevent changing the adjusted/set status.
Procedure
1. Press to turn off the monitor.
2. Press holding down to turn on the monitor.
You can toggle between Lock and Unlock by performing steps 1 and 2.
Note
• The following operations are available even if the buttons are locked:
- Turning on or off the monitor with the Power button
3-4. Setting the EIZO Logo Display
You can choose to display or not to display the EIZO logo, which appears when you turn on the monitor.
Procedure
1. Press to turn off the monitor.
2. Press holding down to turn on the monitor.
The EIZO logo display setting is toggled by performing the operation in steps 1 and 2.