Eizo Radiforce MX241W User manual

Important
Please read this User’s Manual and Setup Manual (separate volume)
carefully to familiarize yourself with safe and effective usage.
Please read the Setup Manual (separate volume)
The latest User’s Manual is available for download from our site:
http://www.radiforce.com
•
•
Cover

2
SAFETY SYMBOLS
This manual uses the safety symbols below. They denote critical information. Please read them carefully.
WARNING
Failure to abide by the information in a WARNING may result in serious injury and can be life threatening.
CAUTION
Failure to abide by the information in a CAUTION may result in moderate injury and/or property or product
damage.
Indicates a prohibited action.
Indicates to ground for safety.
Product specication may vary with sales areas.
Conrm the specication in the manual written in language of the region of purchase.
It shall be assured that the nal system is in compliance to IEC60601-1-1 requirement.
Power supplied equipment can emit electromagnetic waves, that could inuence, limit or result in
malfunction of the monitor.
Install the equipment in a controlled environment, where such effects are avoided.
This is a monitor intended for use in a medical image system. It does not support the display of
mammography images for diagnosis.
•
•
•
Copyright© 2009 EIZO NANAO CORPORATION All rights reserved.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by
any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO NANAO
CORPORATION.
EIZO NANAO CORPORATION is under no obligation to hold any submitted material or information
condential unless prior arrangements are made pursuant to EIZO NANAO CORPORATION’s receipt of
said information.
Although every effort has been made to ensure that this manual provides up-to-date information, please
note that EIZO monitor specications are subject to change without notice.
Apple and Macintosh are registered trademarks of Apple Inc.
VGA is a registered trademark of International Business Machines Corporation.
Windows and Windows Vista are registered trademarks of Microsoft Corporation.
The round gothic bold bit map font used for this product is designed by Ricoh.
DisplayPort icon and VESA are trademarks and registered trademarks of Video Electronics Standards Association.
PowerManager is a trademark of EIZO NANAO CORPORATION.
EIZO, RadiCS, RadiForce, RadiNET and ScreenManager are registered trademarks of EIZO NANAO CORPORATION
in Japan and other countries.

3
PRECAUTIONS
PRECAUTIONS
IMPORTANT!
This product has been adjusted specically for use in the region to which it was originally shipped.
If operated outside the region to which it was originally shipped, the product may not perform as stated
in the specications.
To ensure personal safety and proper maintenance, please read this section and the caution statements
on the unit (refer to the gure below).
●Location of the Caution Statements
●Symbols on the unit
Symbol This symbol indicates
Main Power Switch
Press to turn the monitor’s main power off
Main Power Switch
Press to turn the monitor’s main power on.
Power Button
Press to turn the monitor’s power on or off.
Alternating current
Alerting electrical hazard
Caution
Refer to SAFETY SYMBOLS section in this manual.
•
•

4PRECAUTIONS
WARNING
If the unit begins to emit smoke, smells like something is burning, or makes
strange noises, disconnect all power connections immediately and contact
your dealer for advice.
Attempting to use a malfunctioning unit may result in re, electric shock, or equipment
damage.
Do not open the cabinet or modify the unit.
Opening the cabinet or modifying the unit may result in re, electric shock, or burn.
Refer all servicing to qualied service personnel.
Do not attempt to service this product yourself as opening or removing covers may result in
re, electric shock, or equipment damage.
Keep small objects or liquids away from the unit.
Small objects accidentally falling through the ventilation slots into the cabinet or spillage
into the cabinet may result in re, electric shock, or equipment damage. If an object or liquid
falls/spills into the cabinet, unplug the unit immediately. Have the unit checked by a qualied
service engineer before using it again.
Place the unit at the strong and stable place.
A unit placed on an inadequate surface may fall and result in injury or equipment damage.
If the unit falls, disconnect the power immediately and ask your dealer for advice.
Do not continue using a damaged unit. Using a damaged unit may result in re or electric
shock.
Set the unit in an appropriate location.
Not doing so may result in re, electric shock, or equipment damage.
Do not place outdoors.
Do not place in the transportation system (ship, aircraft, trains, automobiles, etc.)
Do not place in a dusty or humid environment.
Do not place in a location where water is splashed on the screen (bathroom, kitchen, etc.).
Do not place in a location where the steam comes directly on the screen.
Do not place near heat generating devices or a humidier.
Do not place in an inammable gas environment.
•
•
•
•
•
•
•
To avoid danger of suffocation, keep the plastic packing bags away from
babies and children.
Use the enclosed power cord and connect to the standard power outlet of your
country.
Be sure to remain within the rated voltage of the power cord. Not doing so may result in re
or electric shock. Power supply: 100-120/200-240 Vac, 50/60 Hz
To disconnect the power cord, grasp the plug rmly and pull.
Tugging on the cord may damage and result in re or electric shock.
OK

5
PRECAUTIONS
WARNING
The equipment must be connected to a grounded main outlet.
Not doing so may cause in re or electric shock.
Use the correct voltage.
The unit is designed for use with a specic voltage only. Connection to another voltage
than specied in this User’s Manual may cause re, electric shock, or equipment damage.
Power supply: 100-120/200-240 Vac, 50/60 Hz
Do not overload your power circuit, as this may result in re or electric shock.
•
•
Handle the power cord with care.
Do not place the cord underneath the unit or other heavy objects.
Do not pull on or tie the cord. If the power cord becomes damaged, stop using it. Use of a
damaged cord may result in re or electric shock.
•
•
For the electrical safety, do not connect or disconnect the power cord in the
presence of patients.
Never touch the plug and power cord if it begins to thunder.
Touching them may result in electric shock.
When attaching an arm stand, please refer to the user’s manual of the arm
stand and install the unit securely.
Not doing so may cause the unit to come unattached, which may result in injury or equipment
damage. When the unit is dropped, please ask your dealer for advice.
Do not continue using a damaged unit. Using a damaged unit may result in re or electric
shock. When reattaching the tilt stand, please use the same screws and tighten them securely.
Do not touch a damaged LCD panel directly with bare hands.
The liquid crystal which leaks from the panel is poisonous if it enters the eyes or mouth.
If any part of the skin or body comes in direct contact with the panel, please wash thoroughly.
If some physical symptoms result, please consult your doctor.
Fluorescent backlight lamps contain mercury (the products that have LED
backlight lamps contain no mercury), dispose according to local, state or
federal laws.

6PRECAUTIONS
CAUTION
Handle with care when carrying the unit.
Disconnect the power cord and cables when moving the unit. Moving the unit with the cord
attached is dangerous. It may result in injury.
When handling the unit, grip the bottom of the unit rmly with both hands
ensuring the panel faces outward before lifting.
Dropping the unit may result in injury or equipment damage.
Do not block the ventilation slots on the cabinet.
Do not place any objects on the ventilation slots.
Do not install the unit in a closed space.
Do not use the unit laid down or upside down.
Blocking the ventilation slots prevents proper airow and may result in re, electric shock,
or equipment damage.
•
•
•
Do not touch the plug with wet hands.
Doing so may result in electrical shock.
Use an easily accessible power outlet.
This will ensure that you can disconnect the power quickly in case of a problem.
Periodically clean the area around the plug.
Dust, water, or oil on the plug may result in re.
Unplug the unit before cleaning it.
Cleaning the unit while it is plugged into a power outlet may result in electric shock.
If you plan to leave the unit unused for an extended period, disconnect the
power cord from the wall socket after turning off the power switch for the
safety and the power conservation.

7
PRECAUTIONS
Notice for this monitor
This product is suited to clinical review. It does not support the display of mammography images for diagnosis.
This product has been adjusted specically for use in the region to which it was originally shipped. If the product is
used outside the region, it may not operate as specied in the specications.
This product may not be covered by warranty for uses other than those described in this manual.
The specications noted in this manual are only applicable for power cords and signal cables specied by us.
Use optional products manufactured or specied by us with this product.
As it takes about 30 minutes for the performance of electrical parts to stabilize, adjust the monitor 30 minutes or more
after the monitor power has been turned on.
In order to suppress the luminosity change by long-term use and to maintain the stable luminosity, use of a monitor in
lower brightness is recommended.
When the screen image is changed after displaying the same image for extended periods of time, an afterimage may
appear. Use the screen saver or timer to avoid displaying the same image for extended periods of time.
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime. (Refer to
“Cleaning” on the next page.)
The screen may have defective pixels. These pixels may appear as slightly light or dark area on the screen. This is due
to the characteristics of the panel itself, and not the product.
The backlight of the LCD panel has a xed life span. When the screen becomes dark or begins to icker, please
contact your dealer.
Do not press on the panel or edge of the frame strongly, as this may result in the display malfunction, such as the
interference patterns, etc. If pressure is continually applied to the LCD panel, it may deteriorate or damage your LCD
panel. (If the pressure marks remain on the LCD panel, leave the monitor with a white or black screen. The symptom
may disappear.)
Do not scratch or press on the panel with any sharp objects, such as a pencil or pen as this may result in damage to the
panel. Do not attempt to brush with tissues as this may scratch the LCD panel.
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew condensation
may occur inside and outside the monitor. In that case, do not turn the monitor on and wait until dew condensation
disappears, otherwise it may cause some damages to the monitor.

8PRECAUTIONS
Cleaning
Attention
Never use any solvents or chemicals, such as thinner, benzene, wax, alcohol, disinfectant, and abrasive cleaner,
which may damage the cabinet or LCD panel.
•
NOTE
Optional ScreenCleaner is recommended for cleaning the panel surface.•
●LCD Panel
Clean the LCD panel with a soft cloth such as cotton cloth or lens cleaning paper.
Remove persistent stains gently with a cloth dampened with a little water, and then clean the LCD
panel again with a dry cloth for better nishing.
●Cabinet
Clean the cabinet with a soft cloth dampened with a little mild detergent.
To use the monitor comfortably
An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor
according to the environmental conditions.
Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.
•
•
•
•
•

9
CONTENTS
CONTENTS
Cover .............................................................1
PRECAUTIONS .....................................................3
Notice for this monitor............................................. 7
CONTENTS.............................................................9
Chapter 1 Introduction ..................................... 10
1-1. Features...........................................................10
1-2. Controls and Functions.................................11
1-3. Utility Disk.......................................................11
●Disk contents and software overview...............11
● To RadiCS LE or ScreenManager Pro
for Medical.........................................................11
1- 4. Basic Operation and Functions....................12
Basic operation of Adjustment menu................12
Functions..............................................................13
Chapter 2 Adjusting Screen............................. 14
2-1. Setting Screen Resolution...............................14
Compatible Resolutions/Frequencies...............14
Setting Resolution...............................................14
●Windows Vista ..................................................14
●Windows XP......................................................14
●Mac OS X..........................................................14
2-2. Displaying Screen Correctly.........................15
Digital Input..........................................................15
Analog Input.........................................................15
2-3. Color Adjustment...........................................19
● To select the display mode (CAL Switch) .........19
●To perform advanced adjustments ...................19
●Adjustment items in each mode....................... 20
●To adjust the brightness [Brightness]................21
●To adjust the contrast [Contrast].......................21
●To adjust the color temperature
[Temperature]....................................................21
●To adjust the gamma value [Gamma].............. 22
●To adjust the hue [Hue].................................... 22
●To adjust the color saturation [Saturation]....... 22
●To enhance the outline of the image [Outline
Enhancer]......................................................... 23
●To adjust the gain value [Gain]......................... 23
● To adjust six colors [6 Colors].......................... 23
2-4. Displaying Lower Resolutions..................... 24
●To change screen size [Screen Size]................24
Chapter 3 Setting Monitor................................25
3-1. Enabling/Disabling Mode Selection
[Mode Preset]................................................. 25
3-2. Locking Buttons [Key Lock] ........................ 25
3-3. Setting the EIZO Logo Display [Logo]........ 26
3-4. Setting Orientation [Orientation] ................ 26
●To set the orientation of the Adjustment
menu ................................................................ 26
3-5. Setting Language [Language]..................... 26
3-6. Setting the Display Position of the
Adjustment Menu [Menu Position].............. 27
3-7. Restoring the Default Setting...................... 27
●To reset color adjustment values
[Color Reset].................................................... 27
●To reset all adjustments to the factory default
settings [All Reset]........................................... 27
Chapter 4 Power Saving Function...................28
4-1. Setting the Power Saving [Power Save] ..... 28
4-2. Setting Power Indicator
[Power Indicator]........................................... 28
4-3. Setting Monitor’s Automatic Brightness
Adjustment [Auto EcoView]......................... 29
Chapter 5 Troubleshooting .............................. 30
Chapter 6 Reference.........................................33
6-1. Attaching an Arm .......................................... 33
6-2. Connecting More than Two PCs to the
Monitor ........................................................... 34
●To switch the input signal................................. 34
●To set input signal selection [Input Signal]....... 35
6-3. Making Use of USB
(Universal Serial Bus)................................... 36
● Required System Environment ........................ 36
●Connection Procedure
(Setup of USB Function) .................................. 36
6-4. Displaying Monitor Information....................37
●Displaying monitor information by
pressing ........................................................37
●Displaying signal information [Signal Info]........37
●Displaying monitor information [Monitor Info]...37
6-5. Specications................................................ 38
6-6. Glossary......................................................... 42
6-7. Preset Timing................................................. 44
FCC Declaration of Conformity .........................45
EMC Information .................................................46

10 Chapter 1 Introduction
Chapter 1 Introduction
Thank you very much for choosing an EIZO Color Monitor.
1-1. Features
24” wide format LCD
Applicable to the resolution 1920 dots x 1200 lines
Applicable to DisplayPort (applicable to 8 bit or 10 bit, not applicable to audio signals)
3 signal input terminals (DVI-I x 2, DisplayPort x 1)
CAL Switch function for selecting an optimal calibration mode
“2-3. To select the display mode (CAL Switch)” (page 19)
DICOM mode (CAL Switch function) (page 42)
The quality control software “RadiCS LE” (for Windows) used to calibrate the monitor is included
“1-3. Utility Disk” (page 11)
The software “ScreenManager Pro for Medical” (for Windows) to adjust the screen using the mouse
and keyboard is included
“1-3. Utility Disk” (page 11)
Frame Synchronous mode supported (59 - 61 Hz)
Power saving function
This product is equipped with power saving function.
Power Consumption when main power switch is Off: 0W
Equipped with main power switch.
Turning off the main power switch completely shuts off power supply to the monitor while the monitor is not
used.
Auto EcoView function
The sensor on the front side of the monitor detects the environmental brightness to adjust the screen brightness
automatically and comfortably.
Excessively high brightness may lead a damage to the natural environment as well as to your eyes. Suppressing
the excessively high brightness will be helpful to reduce the power consumption and the damage to your eyes.
“4-3. Setting Monitor’s Automatic Brightness Adjustment [Auto EcoView]” (page 29)
HDCP (High-bandwidth Digital Content Interface)
Portrait/Landscape display available (rotate 90 degrees clockwise)
NOTE
This monitor supports the Portrait/Landscape display. This function allows you to change the orientation of the
Adjustment menu when using the monitor screen in vertical display position. (Refer to “To set the orientation of
the Adjustment menu [Orientation]” on page 26.)
For using the monitor with “Portrait” position, the graphics board supporting portrait display is required. When
using the monitor with “Portrait” position, the setting needs to be changed depending on the graphics board used
in your PC. Refer to the manual of the graphics board for details.
•
•
•
•
•
•
•
•
•
•
•
•
-
-
•
•

11
Chapter 1 Introduction
1-2. Controls and Functions
124567810
39
Operation buttons
Adjustment menu
Sensor (AutoEcoView) 6. button
button 7. button
button 8. button
button 9. button
button 10. Power Indicator
Indicator status Operation status
Blue The screen is displayed
Orange Power saving
Off Main Power Switch / Power button off
1-3. Utility Disk
An “EIZO LCD Utility Disk” (CD-ROM) is supplied with the monitor. The following table shows the
disk contents and the overview of the software programs.
●Disk contents and software overview
The disk includes application software programs for adjustment, and User’s Manual. Refer to “Readme.
txt” le on the disk for software startup procedures or le access procedures.
Item Overview
A “Readme.txt” le
RadiCS LE (for Windows) RadiCS LE is quality control software used to calibrate the
monitor and manage the calibration history. (A PC must be
connected to the monitor with the supplied USB cable.) Refer
to the description later.
ScreenManager Pro for Medical
(for Windows) A utility software program to control monitor adjustments from a PC using its mouse and keyboard. (A PC must be connected
to the monitor with the supplied USB cable.) Refer to the
description later.
User’s Manual (PDF le)
●To RadiCS LE or ScreenManager Pro for Medical
Refer to the corresponding User’s Manual on the CD-ROM disk in order to install and use the software.
When using this software, you will need to connect a PC to the monitor with the supplied USB cable. For
more information refer to the “6-3. Making Use of USB (Universal Serial Bus)” (page 36).
1.
2.
3.
4.
5.

12 Chapter 1 Introduction
1- 4. Basic Operation and Functions
Basic operation of Adjustment menu
1Displaying Adjustment Menu
Press .
The adjustment menu appears.
Current mode
Menu title
Settings
Menu
Item
2Adjusting/Setting
Choose a menu to adjust/set with , and press .
Choose an item to adjust/set with , and press .
Adjust/set the selected item with , and press .
3Exiting
Press a few times.
The adjustment menu nishes.
1.
2.
3.

13
Chapter 1 Introduction
Functions
The following table shows all the Adjustment menu’s adjustment and setting menus.
Main Menu Item Adjusting/Setting
Color Brightness “2-3. Color Adjustment” (page 19)
Contrast
Temperature
Gamma
Advanced
Settings Hue
Saturation
Outline Enhancer
Gain
6 Colors
Color Reset “3-7. Restoring the Default Setting”
(page 27)
Screen Screen Size “2-4. Displaying Lower Resolutions”
(page 24)
Analog
Adjustment Auto Adjustment “2-2. Displaying Screen Correctly”
(page 15)
Range Adjustment
Clock
Phase
Hor.Position
Ver.Position
PowerManager Power Save “4-1. Setting the Power Saving” (page 28)
Auto EcoView “4-3. Setting Monitor’s Automatic Brightness
Adjustment” (page 29)
Power Indicator “4-2. Setting Power Indicator” (page 28)
Menu Settings Language “3-5. Setting Language” (page 26)
Orientation “3-4. Setting Orientation” (page 26)
Menu Position “3-6. Setting the Display Position of the
Adjustment Menu” (page 27)
Tools Input Selection “6-2. Connecting More than Two PCs to the
Monitor” (page 34)
Mode Preset “3-1. Enabling/Disabling Mode Selection”
(page 25)
Signal Info “6-4. Displaying Monitor Information”
(page 37)
Monitor Info
All Reset “3-7. Restoring the Default Setting”
(page 27)
* The adjusting/setting function on the <Color> menu depend on the selected Color mode (page 20). The above table
shows the sub menus when the “Custom” mode is selected (See “2-3. Color Adjustment” (page 19)).

14 Chapter 2 Adjusting Screen
Chapter 2 Adjusting Screen
2-1. Setting Screen Resolution
Compatible Resolutions/Frequencies
For details on compatible resolutions, refer to “Compatible Resolutions/Frequencies” in the Setup
Manual.
Setting Resolution
When you connect the monitor to the PC and nd that the resolution is improper, or when you want to
change the resolution, follow the procedure below.
●Windows Vista
Right-click the mouse anywhere on the desktop except for icons.
From the displayed menu, click “Personalize”.
On the “Personalization” window, click “Display Settings”.
On the “Display Settings” dialog, select the “Monitor” tab and select desired resolution in the
“Resolution” eld.
Click the “OK” button.
When a conrmation dialog is displayed, click “Yes”.
●Windows XP
Right-click the mouse anywhere on the desktop except for icons.
From the displayed menu, click “Properties”.
When the “Display Properties” dialog is displayed, click the “Settings” tab and select desired
resolution for “Screen resolution” under “Display”.
Click the “OK” button to close the dialog.
●Mac OS X
Select “System Preferences” from the Apple menu.
When the “System Preferences” dialog is displayed, click “Displays” for “Hardware”.
On the displayed dialog, select the “Display” tab and select desired resolution in the “Resolutions”
eld.
Your selection will be reected immediately. When you are satised with the selected resolution, close
the window.
1.
2.
3.
4.
5.
6.
1.
2.
3.
4.
1.
2.
3.
4.

15
Chapter 2 Adjusting Screen
2-2. Displaying Screen Correctly
Digital Input
When digital signals are input, images are displayed correctly based on the preset data of the monitor.
When performing advanced adjustment, see “2-3 Color Adjustment” (page 19) and subsequent pages.
Analog Input
Attention
Wait 30 minutes or more from monitor power on before starting adjustments.
(Allow the monitor to warm up for at least 30 minutes before making adjustments.)
•
The monitor screen adjustment is used to suppress ickering of the screen or adjust screen position and
screen size correctly according to the PC to be used.
The auto adjustment function works when lling/satisfying all of the following conditions
When a signal is input into the monitor for the rst time or when the resolution or Vertical/
Horizontal Frequency not displayed before is set
When signals with the vertical resolution over 480 are input
•
•
If the screen is not displayed correctly even after performing the auto adjustment, perform the screen
adjustments according to the procedures on the following pages to use the monitor comfortably.
[Adjustment Procedure]
1 Perform the auto adjustment.
● To adjust ickering, screen position, and screen size automatically [Auto Adjustment]
Procedure
Choose <Screen> from the Adjustment menu, and press .
Choose <Analog Adjustment> from the <Screen> menu, and press .
Choose <Auto Adjustment>, and press .
The auto adjustment function works (the message “In Progress” appears) to correctly adjust the ickering, screen
position, and screen size correctly.
When the auto adjustment is completed, a message appears. Select “OK” to conrm the new settings or “Cancel”
to restore the previous settings, and press .
Attention
This function works correctly when an image is fully displayed over the Windows or Macintosh display area. It
does not work properly when an image is displayed only on a part of the screen (command prompt window, for
example) or when a black background (wallpaper, etc.) is in use.
This function does not work correctly with some graphics boards.
•
•
If the screen is not displayed correctly even after adjusting in step 1 above, perform the adjustments
according to the procedures on the following pages. When the screen is displayed correctly, go to step
5 “To adjust color gradation automatically [Range Adjustment]”.
1.
2.
3.

16 Chapter 2 Adjusting Screen
2Prepare the display pattern for the analog display adjustment.
Download the “Screen adjustment pattern les” from our site: http://www.radiforce.com
NOTE
For details and instructions on opening the “Screen adjustment pattern les”, refer to the “Readme.txt” le. •
3 Perform the auto adjustment again with the analog screen adjustment pattern
displayed.
● To adjust ickering, screen position, and screen size automatically [Auto Adjustment]
Procedure
Display Pattern 1 of the screen adjustment pattern les in full screen on the monitor.
Choose <Screen> from the Adjustment menu, and press .
Choose <Analog Adjustment> from the <Screen> menu, and press .
To proceed with the subsequent adjustments, select an item in <Analog Adjustment> of the <Screen> menu.
Choose <Auto Adjustment>, and press .
The auto adjustment function works (the message “In Progress” appears) to adjust the ickering, screen position,
and screen size correctly.
When the auto adjustment is completed, a message appears. Select “OK” to conrm the new settings or “Cancel”
to restore the previous settings, and press .
If the screen is not displayed correctly even after adjusting in step 3 above, perform the adjustments
according to the procedures on the following pages. When the screen is displayed correctly, go to step
5 “To adjust color gradation automatically [Range Adjustment]”.
1.
2.
3.
4.

17
Chapter 2 Adjusting Screen
4Perform advanced adjustments for the following using the <Screen> menu of
the <Analog Adjustment>.
Adjust the clock, phase and position, in this order.
●To eliminate vertical bars [Clock]
Procedure
Choose <Clock> from the <Analog Adjustment> menu, and press .
Adjust the clock with or .
Press slowly so as not to miss the adjustment point.
Press to exit the adjustment.
When blurring, ickering or bars appear on the screen after adjustment, proceed to [Phase] to remove ickering
or blurring.
● Remove ickering or blurring [Phase]
Procedure
Choose <Phase> from the <Analog Adjustment> menu, and press .
Adjust the phase with or .
Press to exit the adjustment.
Attention
Flickering or blurring may not be eliminated depending on your PC or graphics board.•
●To correct screen position [Hor.Position] [Ver.Position]
NOTE
Since the number of pixels and the pixel positions are xed on the LCD monitor, only one position is provided to
display images correctly. The position adjustment is made to shift an image to the correct position.
•
Procedure
Choose <Hor.Position> or <Ver.Position> from the <Analog Adjustment> menu, and press .
Adjust the position with or .
Press to exit the adjustment.
1.
2.
3.
1.
2.
3.
1.
2.
3.

18 Chapter 2 Adjusting Screen
5Adjust the color gradation.
●To adjust color gradation automatically [Range Adjustment]
Every color gradation (0 to 255) can be displayed by adjusting the signal output level.
Procedure
Display Pattern 2 in full screen on the monitor using the screen adjustment pattern les.
Choose <Range Adjustment> from the <Analog Adjustment> menu, and press .
The color gradation is adjusted automatically.
When the auto adjustment is completed, a message appears. Select “OK” to conrm the new settings or “Cancel”
to restore the precious settings, and press .
Close the Pattern 2.
1.
2.
3.

19
Chapter 2 Adjusting Screen
2-3. Color Adjustment
●To select the display mode (CAL Switch)
CAL Switch allows you to select easily the adequate mode suitable for the monitor’s application.
CAL Switch mode
Mode Purpose
1-DICOM Available to display in DICOM mode.
2-Custom Available for the color settings according to your preference.
3-CAL Displays the screen adjusted by calibration software.
4-Text Suitable for displaying texts for word processing or spreadsheets.
The mode menu
appears.
Procedure
Press .
Mode menu appears at the lower left of the screen.
The mode among the list is highlighted in turn each time is pressed.
You can switch the current mode with or while the mode menu is being displayed.
→1-DICOM←→2-Custom←→3-CAL←→4-Text←
NOTE
The Adjustment menu and the Mode menu cannot be displayed at the same time.
You can disable a specic mode to be selected. For more information, refer to “3-1 Enabling/Disabling Mode
Selection” (page 25).
•
•
●To perform advanced adjustments
The <Color> menu of the Adjustment menu allows you to set and save the independent color adjustment
for each mode.
Attention
Wait 30 minutes or more from monitor power on before starting the color adjustment.
(Allow the monitor to warm up for at least 30 minutes before making adjustments.)
Perform the range adjustment rst when adjusting color for analog input signals.
(Refer to “To adjust color gradation automatically” on page 18).
The same image may be seen in different colors on multiple monitors due to their monitor-specic characteristics.
Make ne color adjustment visually when matching colors on multiple monitors.
•
•
•
NOTE
The values shown in “%” or “K” are available only as reference.•
1.
2.

20 Chapter 2 Adjusting Screen
●Adjustment items in each mode
According to the mode selected, the adjustable function differs.
(You can not select any function unavailable for adjustment or setting.)
The adjustments or settings made for each mode are applied to all input signals.
For the adjustment method of each function, refer to subsequent pages.
√: Adjustment available ―: Invalid for adjustment
Icon Function CAL Switch mode
1-DICOM 2-Custom* 3-CAL* 4-Text*
Brightness √ √ √ √
Contrast ― √ ― √
Temperature ― √ ― √
Gamma ― √ ― √
Hue ― √ ― √
Saturation ― √ ― √
Outline
Enhancer ― √ ― √
Gain ― √ ― ―
6 Colors ― √ ― ―
Color Reset √ √ √ √
* If you adjust the calibration in this mode using the calibration kit exclusive for to this monitor (RadiCS LE as an
accessory shown on page 41), only Brightness and Reset is adjustable.