Eizo FlexScan EV2457 User manual

Important
Please read this “User’s Manual”, and “PRECAUTIONS” (separate
volume) carefully to familiarize yourself with safe and effective usage.
•Refer to the “Setup Guide” for information on the installation /
connection of the monitor.
•For the latest product information including the “User’s Manual”,
refer to our web site :
www.eizoglobal.com
Color LCD Monitor
User’s Manual

Location of Caution Statement
This product has been adjusted specically for use in the region to which it was originally shipped. If
operated outside this region, the product may not perform as stated in the specications.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by
any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.
EIZO Corporation is under no obligation to hold any submitted material or information condential unless
prior arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although every
effort has been made to ensure that this manual provides up-to-date information, please note that EIZO
monitor specications are subject to change without notice.
2

Notice for this monitor
This product is suited to general purposes like creating documents, viewing multimedia content (Assuming
usage of approximately 12 hours per day).
If using this product for the following kinds of applications, where an extremely high degree of reliability and
safety is required, then measures should be in place to maintain safety while using this product.
• Transportation equipment (ships, aircraft, trains, and automobiles)
• Safety devices (Disaster prevention systems, security control systems, etc.)
• Life-critical devices (medical devices, such as life-support devices and operating room devices)
• Nuclear energy control devices (Nuclear energy control systems, security control systems of nuclear facilities, etc.)
• Major system communication devices (operation control systems of transportation systems, air trafc control systems, etc.)
This product has been adjusted specically for use in the region to which it was originally shipped. If the
product is used outside the region, it may not operate as specied in the specications.
This product may not be covered by warranty for uses other than those described in this manual.
The specications noted in this manual are only applicable when the following are used:
• Power cords provided with the product
• Signal cables specied by us
Only use optional products manufactured or specied by us with this product.
If you place this product on a lacquer-coated desk, the color may adhere to the bottom of the stand due to
the composition of the rubber. Check the desk surface before use.
It takes about 30 minutes (under our measurement conditions) for the monitor display to stabilize. Please
wait 30 minutes or more after the monitor power has been turned on, and then adjust the monitor.
Monitors should be set to a lower brightness to prevent a loss in the screen quality caused by long-term use
and to maintain stable use.
When the screen image is changed after displaying the same image for extended periods of time, an
afterimage may appear. Use the screen saver or power save function to avoid displaying the same image for
extended periods of time. Depending on the image, an afterimage may appear even if it was displayed for
a short period of time. To remove such a phenomenon, change the image or keep the power turned off for
several hours.
If the monitor displays continuously over a long period of time, dark smudges or burn-in may appear. To
maximize the life of the monitor, we recommend the monitor be turned off periodically.
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime (refer
to “Cleaning” (page 4)).
The LCD panel is manufactured using high-precision technology. Although, missing pixels or lit pixels may
appear on the LCD panel, this is not a malfunction. Percentage of effective dots: 99.9994 % or higher.
The backlight of the LCD panel has a xed lifetime. Depending on the usage pattern, such as usage for
long continuous periods, the lifespan of the backlight may run out sooner, requiring replacement. When the
screen becomes dark or begins to icker, please contact your local EIZO representative.
Do not press on the LCD panel or edge of the frame strongly, as this may result in display malfunctions, such
as interference patterns, etc. If pressure is continuously applied to the LCD panel surface, the liquid crystal
may deteriorate or the LCD panel may be damaged. (If the pressure marks remain on the panel, leave the
monitor with a black or white screen. The symptom may disappear.)
Do not scratch or press on the LCD panel with any sharp objects, at this may result in damage to the LCD
panel. Do not attempt to brush with tissues as this may scratch the panel.
3
Notice for this monitor

When the monitor is cold and brought into a room or the room temperature goes up quickly, dew
condensation may occur on the interior and exterior surfaces of the monitor. In that case, do not turn the
monitor on. Instead wait until the dew condensation disappears, otherwise it may cause some damage to the
monitor.
Cleaning
The stains on the cabinet and LCD panel surface can be removed by moistening part of a soft cloth with water.
Attention
• Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet
or LCD panel, and also quality deterioration of the image.
• Never use thinner, benzine, wax, or abrasive cleaner as they may damage the cabinet or LCD panel surface.
Note
• It is recommended that ScreenCleaner (available as an option) be used to clean the cabinet and LCD panel surface.
To use the monitor comfortably
• An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor
according to the environmental conditions.
• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.
4Notice for this monitor

CONTENTS
Notice for this monitor ......................................... 3
Cleaning .................................................................... 4
To use the monitor comfortably ............................. 4
CONTENTS............................................................. 5
Chapter 1 Introduction....................................... 6
1-1. Features ......................................................... 6
●DisplayPort Daisy Chain Connection .............. 6
●High Degree of Flexibility for Installation ........ 7
●Reduction of Power Consumption .................. 8
●Realizing More Convenient Operations
Using Screen InStyle ...................................... 8
1-2. Controls and Functions ............................... 9
●Front ................................................................ 9
●Rear ................................................................10
1-3. Supported Resolutions...............................11
1-4.
Changing the Computer Display Settings ...12
●Windows 10 ....................................................12
●Windows 8.1 / Windows 7 ..............................12
●macOS ...........................................................12
Chapter 2 Basic Adjustment / Setting ............ 13
2-1. Switch Operation Method ...........................13
2-2. Switching Input Signals ..............................14
2-3.
Switching Display Modes (Color Modes) ...14
●Display Modes ................................................14
2-4. Conserving Energy......................................15
2-5. Adjusting Brightness ..................................16
2-6. Adjusting Volume.........................................16
Chapter 3 Advanced Adjustment / Setting .... 17
3-1. Basic Operation of the Setting Menu ........17
3-2. Setting Menu Functions ..............................18
●Color Adjustment ............................................18
●Signal Settings ...............................................21
●Preference Settings ...................................... 23
●Language .......................................................24
●Information .....................................................24
Chapter 4 Administrator Settings................... 25
4-1. Basic Operation of the “Administrator
Settings” Menu............................................ 25
4-2. Functions of the “Administrator
Settings” Menu............................................ 26
Chapter 5 Troubleshooting.............................. 28
5-1. No Picture .................................................... 28
5-2. Imaging Problems....................................... 29
5-3. Problems Related to DisplayPort Daisy
Chain Connection ....................................... 30
5-4. Other Problems............................................31
Chapter 6 Reference ........................................ 32
6-1. Removing the Stand ................................... 32
6-2. Attaching the Optional Arm....................... 33
●Attaching the optional arm (or optional
stand) ............................................................ 33
●Attaching the original stand .......................... 34
6-3. Detaching/Attaching the Cable Holder..... 35
●Detaching the cable holder ........................... 35
●Attaching the cable holder ............................ 35
6-4. Detaching / Attaching the Cable Cover .... 36
●Attaching the cable cover .............................. 36
●Detaching the cable cover .............................37
6-5. Connecting Multiple PCs ........................... 38
●Connection examples ................................... 38
6-6. Using the USB Hub Function..................... 39
●Connection procedure................................... 39
6-7. Specications ............................................. 40
●Accessories ....................................................41
Appendix.............................................................. 42
Trademark ............................................................... 42
License .................................................................... 42
5
CONTENTS

Chapter 1 Introduction
Thank you very much for choosing an EIZO color LCD monitor.
1-1. Features
●
DisplayPort Daisy Chain Connection
The monitor comes equipped with an output terminal ( ), as well as a DisplayPort input terminal. By
using the DisplayPort cable to connect (link together) a maximum of four monitors in a daisy chain
connection, the cables can be arranged optimally.
Note
• DisplayPort daisy chain connection is a function supported by DisplayPort Version 1.2. For this reason, it is
necessary to change the version of the DisplayPort on the monitor outputting the DisplayPort signal from
Version 1.1 (the default setting) to Version 1.2 (refer to “DisplayPort” (page 27)).
• In order to use daisy chain connection, the graphics board of the computer must support Multi-Stream
Transport (MST). For details, contact the manufacturer of the computer or the store where you bought the
product.
• The number of monitors it is possible to connect varies depending on the monitors you are using and the
graphics board of the computer. For details, refer to the compatibility information on our company website.
6Chapter 1 Introduction

●High Degree of Flexibility for Installation
• This product can be used as an external monitor of a notebook computer.
• By attaching the monitor to an arm, the screen can be rotated 180° (upward-downward rotation)
and used in a multi-monitor conguration.
Note
• In order to rotate the display of the monitor 180°, it is necessary to congure the settings for the computer.
7
Chapter 1 Introduction

●Reduction of Power Consumption
This product provides a function that automatically adjusts the screen brightness to reduce power
consumption *1. Power Reduction, CO2 Reduction, and Eco Performance Level can be checked on
the "EcoView Settings" menu. (page 15)
• Auto EcoView
The ambient light sensor on the front of the monitor detects the ambient brightness to automatically
adjust the screen brightness to a comfortable level.
• EcoView Optimizer 2
The monitor automatically adjusts the screen brightness according to the white level of the input
signal. This function can reduce power consumption while maintaining the brightness specied by
the input signal.
*1 Reference values
Maximum power consumption: 59 W (when a USB device is connected and the speakers are working),
standard power consumption: 11 W (brightness 120 cd/m2, when no USB device is connected and the
speakers are not working, at default settings)
●Realizing More Convenient Operations Using Screen InStyle
The "Screen InStyle" monitor control utility enables you to use the monitor more conveniently.
• The monitor color mode can be switched automatically to suit the software to be used.
• When multiple monitors are installed, you can turn the power on and off or change the color mode
of all monitors at the same time.
Note
• Screen InStyle can be downloaded from our web site (www.eizoglobal.com).
• The Windows operating systems are only supported.
8Chapter 1 Introduction

1-2. Controls and Functions
●Front
4321
5 5
1. Ambient light sensor Detects ambient brightness. If you use Auto EcoView, the screen brightness is
automatically adjusted according to the ambient brightness (page 15).
2. Operation switches Displays menus. Operate the switches according to the operation guide (page 17).
3. Power switch Turns the power on or off.
4. Power indicator Indicates the monitor’s operation status.
White: Normal operation mode
Orange: Power saving mode
OFF: Main power / power off
5. Speakers Outputs audio.
9
Chapter 1 Introduction

●Rear
13
12
10
9
11
8
16 17 18 914 15
7
6
6. Handle This handle is used for transportation.
7. Security lock slot Complies with Kensington’s MicroSaver security system.
8. Lock button Use this button to remove the monitor from the stand.
9. USB downstream
port
Connects to a peripheral USB device.
Note
• When connecting (linking together) three or more monitors in a daisy chain
connection using the USB hub function, use the bottom USB downstream port.
10. Headphone jack Connects to headphones.
11. Stereo mini jack If you connect an external device using the stereo mini jack cable, external audio
can be output from the monitor.
12. Cable holder Holds the monitor cables.
13. Stand*1 Adjusts the height and angle (tilt and swivel) of the monitor.
14. Main power switch Turns the main power on or off. : On, : Off
15. Power connector Connects the power cord.
16. Input signal
connectors
The following connectors are available on the monitor rear in order of left to right.
DVI connector
HDMI connector
DisplayPort connector
17. DisplayPort output
connector
When connecting DisplayPorts in a daisy chain connection, this connects to the
DisplayPort input connectors of the other monitors in the conguration. When
making a connection, it is necessary to change the version of the DisplayPort on
the monitor outputting the DisplayPort signal from Version 1.1 (the default setting)
to Version 1.2 (refer to “DisplayPort” (page 27)).
18. USB upstream port Connect the USB cable when using software that requires USB connection or when
using the USB hub function.
*1 An optional arm (or optional stand) can be attached by removing the stand section.
10 Chapter 1 Introduction

1-3. Supported Resolutions
The monitor supports the following resolutions.
Resolution Vertical scan frequency (Hz) DisplayPort HDMI DVI-D
720 × 400 70.087 √ √ √
640 × 480 59.940 √ √ √
640 × 480 60.000 √ √ -
800 × 600 60.317 √ √ √
1024 × 768 60.004 √ √ √
1280 × 800 59.810 √ √ √
1280 × 1024 60.020 √ √ √
1600 × 900 60.000 √ √ √
1600 × 1200 60.000 √ √ √
1680 × 1050 59.954 √ √ √
1680 × 1050 59.883 √ √ √
1920 × 1200 59.950 √ √ √
1920 × 1080 60.000 - √ -
1920 × 1080 59.940 - √ -
720 × 480 (4:3) 60.000 √ √ -
720 × 480 (4:3) 59.940 √ √ -
720 × 480 (16:9) 60.000 √ √ -
720 × 480 (16:9) 59.940 √ √ -
720 (1440) × 480 (4:3) 60.000 - √ -
720 (1440) × 480 (4:3) 59.940 - √ -
720 (1440) × 480 (16:9) 60.000 - √ -
720 (1440) × 480 (16:9) 59.940 - √ -
720 × 576 (4:3) 50.000 - √ -
720 × 576 (16:9) 50.000 - √ -
720 (1440) × 576 (4:3) 50.000 - √ -
720 (1440) × 576 (16:9) 50.000 - √ -
1280 × 720 60.000 √ √ √
1280 × 720 59.940 √ √ -
1280 × 720 50.000 - √ -
1920 × 1080 60.000 √ √ √
1920 × 1080 59.940 √ √ -
1920 × 1080 50.000 - √ -
11
Chapter 1 Introduction

1-4. Changing the Computer Display Settings
If the image is not displayed properly after connecting the monitor to a PC, follow the procedure below to
change the display settings on the computer.
●Windows 10
1. Right-click the mouse anywhere on the desktop except on icons. A menu is displayed.
2. From the displayed menu, click “Display Settings”. The “Settings” screen is displayed.
3. If multiple monitors, including notebook PC screens, are connected to the computer, select “Extend
these displays” in the “Multiple displays” menu, and then click “Keep changes” on the conrmation
screen. After changing the settings, select a monitor in the “Select and rearrange displays” menu.
4. Select the “Make this my main display” option in the “Multiple displays” menu. This enables the
monitor to display images properly.
5. Conrm that the recommended resolution for the monitor is set in the “Resolution” menu.
(“(Recommended)” is displayed after the resolution.)
6. To change the size of text and icons, select a magnication in the menu of zoom percentages
according to personal preference.
7. If a message prompting you to sign out is displayed after changing the settings, sign out and then
sign in again.
●Windows 8.1 / Windows 7
* For Windows 8.1, click the "Desktop" tile on the Start Screen to display the desktop.
1. Right-click the mouse anywhere on the desktop except on icons. A menu is displayed.
2. From the displayed menu, click “Screen resolution”. The settings screen is displayed.
3. If multiple monitors, including notebook PC screens, are connected to the computer, select “Extend
these displays” in the “Multiple displays” menu, and then click “Apply”. Click “Keep changes” on
the conrmation screen.
4. Select a monitor in the “Display” menu, and then select the “Make this my main display” option
and click “Apply”. This enables the monitor to display images properly.
5. Conrm that the recommended resolution for the monitor is set in the “Resolution” menu.
(“(recommended)” is displayed after the resolution.)
6. To change the size of text and icons, click “Make text and other items larger or smaller”, select a
size according to personal preference on the settings screen, and then click “Apply”.
7. If a message prompting you to sign out/log off is displayed after changing the settings, sign out/
log off and then sign in/log in again.
●macOS
1. Select “System Preferences” from the Apple menu.
2. When the “System Preferences” panel is displayed, click “Displays”.
3. If multiple monitors, including notebook PC screens, are connected to the computer, make sure
that “Mirror Displays” is not selected on the “Arrangement” tab. If it is selected, remove the check
mark.
4. Select the “Display” tab, and make sure that “Default for display” is selected for “Resolution”. If
it is not selected, add a check mark. The correct resolution has now been set for your display.
Close the “System Preferences” panel. If multiple monitors, including notebook PC screens, are
connected to the computer, congure these settings in “Display” on each monitor.
5. To select a resolution according to personal preference, select “Scaled” and then select a
resolution (either from a list or icons), and then close the panel.
12 Chapter 1 Introduction

Chapter 2 Basic Adjustment / Setting
This product enables users to change the brightness according to personal preference or to suit the usage
environment, and to reduce power consumption to conserve energy.
This chapter describes the basic functions that can be adjusted and set using the switches on the front of the
monitor.
For advanced adjustment and setting procedures using the Setting menu, see “Chapter 3 Advanced
Adjustment / Setting” (page 17).
2-1. Switch Operation Method
1.
Displaying the operation guide
1. Touch any switch (except ).
The operation guide appears on the screen.
2.
Adjusting / setting
1. Touch a switch for adjustment / setting.
The Adjustment / Setting menu appears.
(A submenu may also be displayed. In this case, select the item for adjustment / setting using and
select .)
2. Perform adjustment / setting with the switches and select to accept the changes.
3.
Exiting
1. Select to exit the menu.
13
Chapter 2 Basic Adjustment / Setting

2-2. Switching Input Signals
When a monitor has multiple signal inputs, the signal to display on-screen can be changed.
Note
• "Screen InStyle" allows you to switch input signals using the shortcut keys on the keyboard.
2-3. Switching Display Modes (Color Modes)
This product is preinstalled with color modes for various display purposes.
By switching the mode according to the purpose and contents of the display, you can display images in
an appropriate manner.
●Display Modes
Color Mode Purpose
User1
User2
Select either of these modes to set a user-dened display mode.
sRGB This mode is suitable for matching color reproduction with peripheral devices that
support sRGB, such as when printing photos taken using a digital camera.
Paper This mode uses color tones and contrast similar to that of paper to produce a printed
paper effect. It is suitable for displaying images from media such as books and
documents.
Movie This mode displays moving images brightly and with a clear-cut three-dimensional
appearance. It is suitable for playing back video content.
DICOM Select this mode to simply display medical purpose digital images based on DICOM®
Part 14.
Attention
• This is not intended to be used for diagnostic purposes.
Note
• "Screen InStyle" allows you to select the color mode automatically according to the software in use.
• In Paper mode, the amount of blue light emitted from the screen is reduced by changing the color tone and
controlling the brightness.
14 Chapter 2 Basic Adjustment / Setting

2-4. Conserving Energy
This monitor is equipped with EcoView functions to enable users to conserve energy.
You can use this function to curtail unnecessary power consumption and save on electricity expenses.
Saving power also reduces carbon dioxide emissions.
Note
• The power saving level (Power Reduction, CO2 Reduction, and Eco Performance Level) can be checked on the
“EcoView Settings” menu. The more indicators that light up representing the Eco Performance Level, the higher
the power saving level attained.
- Power Reduction: the reduction in the backlight’s power consumption as a result of the adjusted brightness
value.
-CO2 Reduction: converted from the “Power Reduction” value, this is an estimate of the quantity of CO2
emissions reduced when using the monitor for 1 hour.
• The numeric value is a result of calculation based on a default setting (0.000555t-CO2 / kWh) determined by a
Japanese ministerial ordinance (2006, Ministry of Economy, Trade and Industry, Ministry of Environment, civil
code article 3) and may differ depending on country and year.
Function Setting
Value Description
Auto EcoView On
Off
The ambient light sensor on the front of the monitor
detects the ambient brightness to automatically adjust
the screen brightness to a comfortable level using Auto
EcoView. The power consumption of the backlight can
be curtailed by adjusting the brightness to an appropriate
level.
This function can also mitigate eye strain and tiredness
caused by a screen that is too bright or too dark.
Note
• Be careful not to block the ambient light sensor on the
lower side of the monitor when using Auto EcoView.
• Even when Auto EcoView is set to “On”, you can
change the brightness of the monitor using the
operation switches ( ) on the front of the monitor or
in the color adjustment settings. The manner in which
Auto EcoView changes the brightness will also vary
depending on the value you set.
• When “DICOM” is selected for the color mode, the
Auto EcoView setting is turned “Off”.
EcoView Optimizer 2 On
Off
The monitor automatically adjusts the screen brightness
according to the white level of the input signal.
This function can reduce power consumption while
maintaining the brightness specied by the input signal.
Note
• When “Movie” is selected for the color mode, EcoView
Optimizer 2 is set to “Off”.
• When set to “On”, the appearance of pale colors may
change. If this bothers you, set this function to “Off”.
15
Chapter 2 Basic Adjustment / Setting

2-5. Adjusting Brightness
The brightness of the screen can be adjusted to suit the installation environment or personal preference.
The screen brightness is adjusted by changing the brightness of the backlight (light source from the LCD
back panel).
Setting Value
0 to 100
2-6. Adjusting Volume
The volume of the speakers and headphones can be set individually.
Setting Value
0 to 30
When the speakers are
connected
When the headphones are
connected
16 Chapter 2 Basic Adjustment / Setting

Chapter 3 Advanced Adjustment / Setting
This chapter describes the advanced monitor adjustment and setting procedures using the Setting menu.
For basic functions, see “Chapter 2 Basic Adjustment / Setting” (page 13).
3-1. Basic Operation of the Setting Menu
1.
Menu display
1. Touch any switch (except ).
The operation guide appears.
2. Select .
The Setting menu appears.
2.
Adjusting / setting
1. Select a menu to adjust / set with and select .
The Sub menu appears.
2. Select an item to adjust / set with and select .
The Adjustment / Setting menu appears.
3. Perform adjustment / setting with or and select to accept the changes.
The Sub menu appears.
Selecting during adjustment / setting will cancel the adjustment / setting and restore the state prior to
making changes.
3.
Exiting
1. Selecting several times will terminate the Setting menu.
17
Chapter 3 Advanced Adjustment / Setting

3-2. Setting Menu Functions
●Color Adjustment
The color mode settings can be adjusted according to personal preference.
Functions that can be adjusted differ depending on the color mode.
√: Adjustable -: Not adjustable
Function
Color Mode
User1
User2 sRGB Paper Movie DICOM
Brightness √√√√-
Contrast √- - √-
Temperature √-√ √ -
Gamma √----
Advanced
Settings
Overdrive √----
Hue √- - √-
Saturation √- - √-
Gain √----
Reset √√√√-
Attention
• It takes about 30 minutes for the monitor display to stabilize. Please wait 30 minutes or more after power to
the monitor has been turned on before adjusting the monitor.
• The same image may be observed in different colors on multiple monitors due to monitor-specic
characteristics. Make ne color adjustments visually when matching colors across multiple monitors.
18 Chapter 3 Advanced Adjustment / Setting

Function Setting
Value Description
Color Mode User1
User2
sRGB
Paper
Movie
DICOM
Select the desired mode according to the monitor application.
The color mode settings can also be adjusted according to personal
preference. Select the mode for adjustment and perform adjustment
using the relevant functions.
Note
• For details on the adjustment status of each mode, see “2-3.
Switching Display Modes (Color Modes)” (page 14).
Brightness 0 to 100 The screen brightness is adjusted by changing the brightness of the
backlight (light source from the LCD back panel).
Note
• If the image is too dark even when the brightness is set to 100,
adjust the contrast.
Contrast 0 to 100 The brightness of the screen is adjusted by varying the video signal
level.
Note
• A contrast of 50 displays every color gradation.
• When adjusting the monitor, it is recommended to perform
brightness adjustment, which does not lose gradation
characteristics, prior to contrast adjustment.
• Perform contrast adjustment in the following cases.
- If the image is too dark even when the brightness is set to 100
(Set the contrast to higher than 50.)
Temperature Off
4000 K to
10000 K
(in
increments of
500 K. 9300 K
is included.)
Adjust the color temperature.
The color temperature is normally used to express the hue of “White”
and/or “Black” with a numerical value. The value is expressed in
degrees “K” (Kelvin).
The screen becomes reddish at low color temperatures and bluish at
high color temperatures, similar to the temperatures of a ame. A gain
preset value is set for each color temperature setting value.
Note
• The value shown in “K” is available only as a reference.
• “Gain” allows you to perform more advanced adjustment.
• If set to “Off”, the image is displayed in the preset color of the
monitor (Gain: 100 for each RGB channel).
• When the gain is changed, the color temperature setting changes
to “Off”.
Gamma 1.8
2.0
2.2
2.4
Adjust the gamma.
While the brightness of the monitor varies depending on the input
signal, the variation rate is not proportional to the input signal.
Maintaining the balance between the input signal and brightness of
the monitor is referred to as “Gamma correction”.
Note
• If "sRGB" is selected for the color mode, the gamma value is
xed to "sRGB".
• If “Paper” is selected for the color mode, “Paper” is displayed for
the gamma value.
• If “DICOM” is selected for the color mode, “DICOM” is displayed
for the gamma value.
19
Chapter 3 Advanced Adjustment / Setting

Function Setting
Value Description
Advanced
Settings
Overdrive Enhanced
Standard
Off
This function allows you to set the overdrive intensity based on the
use of the monitor.
Image lag can be reduced by using the “Enhanced” setting when
displaying moving images.
Note
• Depending on the resolution of the input signal and the setting of
“Picture Expansion” (from the “Signal” menu), overdrive may be
set to “Off”.
Hue -50 to 50 Adjust the hue.
Note
• Using this function may prevent some color gradations from being
able to be displayed.
Saturation -50 to 50 Adjust the color saturation.
Note
• Using this function may prevent some color gradations from being
able to be displayed.
• The minimum value (-50) changes the screen to monochrome.
Gain 0 to 100 The brightness of each red, green, and blue color component is
referred to as “Gain”. The hue of “white” can be changed by adjusting
the gain.
Note
• Using this function may prevent some color gradations from being
able to be displayed.
• The gain value changes according to the color temperature.
• When the gain is changed, the color temperature setting changes
to “Off”.
Reset - Reset any color adjustments for the currently selected color mode
back to the default settings.
20 Chapter 3 Advanced Adjustment / Setting