EK-Quantum Kinetic FLT 80 D5/DDC Body User manual

USER GUIDE
RESERVOIR
EK-Quantum
Kinetic FLT 80 D5/DDC Body

Before you start using this product, please follow these basic guidelines:
Please carefully read the manual before beginning with the
installation process!
The EK fittings require only a small amount of force to screw
them firmly in place since the liquid seal is ensured by the
rubber o-ring gaskets.
The use of corrosion inhibiting coolants is always
recommended for any liquid cooling system. EKWB
recommends any of the EK-Cryofuel for worry-free usage.

- 3 -
TABLE OF CONTENTS
BOX CONTENTS 4
RESERVOIR DIMENSIONS 5
TECHNICAL SPECIFICATIONS AND PRODUCT PARTS 6
GENERAL INFORMATIONS 7
D5 PUMP VERSION 8
ATTACHING THE D5 PUMP ON TO THE RESERVOIR 8
DDC PUMP VERSION 9
ATTACHING THE DDC PUMP ON TO THE RESERVOIR 9
INSTALLING EK-QUANTUM KINETIC FLT WITH SUPPLIED MOUNTS 10
INSTALLING EK-QUANTUM KINETIC FLT USING UNI PUMP BRACKET 12
ATTACHING EK-QUANTUM KINETIC FLT WITH SUPPLIED MOUNTS 12
ATTACHING THE FITTINGS 14
CONNECTING THE D-RGB LED STRIP 15
TESTING THE LOOP 15
SUPPORT AND SERVICE 16
SOCIAL MEDIA 16

- 4 -
BOX CONTENTS
8 mm
10 mm
25 mm
EK-Loop Multi Allen Key (1 pc)
M4 Nut (4 pcs)
DDC Mount (2 pcs)
D5 Mount (2 pcs)
Allen Key 2.5 mm (1 pc)
M4 x 10 DIN7984 Screw (4 pcs)
M4 x 25 DIN7984 Screw (4 pcs)
M4 x 8 DIN7984 Screw (4 pcs)
EK-Quantum Kinetic FLT 80 D5/DDC Body PVC Washer M4 (4 pcs)
Mounting Mechanism – You may not need every screw from
this package. EAN: 102171

- 5 -
RESERVOIR DIMENSIONS
80 mm
120 mm
20 mm
45 mm
73 mm
101 mm
52 mm
36 mm
14.5 mm
17 mm
45 mm
73 mm
101 mm

- 6 -
TECHNICAL SPECIFICATIONS AND PRODUCT PARTS
Position EAN Description Quantity
1100663 EK Badge 1
28312 M4 x 16 7991DIN Screw 5
3103116 EK Plug G1/4 7
4103773 Alu cover (Black) 1
5100199 D-RGB LED Strip 1
6103989 Top plexi plate 1
75092 OR 12 x 1.5 1
8101921
OR 88 x 2 1
9103772
Bottom plexi plate 1
10 102214 M4 x 30 DIN7991 Screw 3
11 101803 Pump holder 1
12 8311 M4 x 20 DIN7984 Screw 4
1
12
4
8
7
10
2
3
5
6
9
11

- 7 -
GENERAL INFORMATIONS
FLT Reservoir can be mount in multiple directions. Vertically and
horizontally position is optional.
Do not mount FLT Reservoir when the pump is in dead position.

- 8 -
D5 PUMP VERSION
ATTACHING THE D5 PUMP ON TO THE RESERVOIR
STEP 1
Remove the preinstalled Pump Holder using 2.5 mm Allen Key. Store
the screws and pump holder for later use.
STEP 2
Make sure that the gasket (o- ring) is placed into the groove.
STEP 3
Carefully attach the D5 Pump and Pump Holder (as shown on the
photo). After that, secure all the parts together with M4 x 20 DIN 7984
Screws. Tighten the screws using enclosed 2.5 mm Allen Key.
STEP 1
STEP 2
STEP 3
PUMP HOLDER
52 x 3 GASKET
M4 x 20 DIN7984
M4 x 20 DIN7984

- 9 -
DDC PUMP VERSION
ATTACHING THE DDC PUMP ON TO THE RESERVOIR
STEP 1
Remove the preinstalled Pump Holder and screws using 2.5mm
Allen Key.
STEP 2
Carefully attach the DDC pump and make sure that gasket (46 x 2.5) is
placed correctly. Sealing gasket is included in additional bag. Secure
the pump with four (4) M4 x 25 7984DIN screws (see sample photo).
Tighten the screws using enclosed 2.5 mm Allen Key.
STEP 1
STEP 2
PUMP HOLDER
DDC PUMP
M4 x 25 DIN7984
M4 x 20 DIN7984

- 10 -
INSTALLING EK-QUANTUM KINETIC FLT WITH SUPPLIED MOUNTS
STEP 1
D5 MOUNT
DDC MOUNT
D5 Version:
DDC Version:
To enable installation of the reservoir where clearance for the pump
is required, EK supplies a pair of FLT mounts along with M4 nuts,
washers and additional screws.
In case of using standard fan mounting location, only one
supplied mount is required.
STEP 1
Position the mounts as shown on the picture!

- 11 -
STEP 2
Screw the mounts in place using supplied M4 x 8 screws and 2.5 mm
allen key.
STEP 2
M4 x 8 DIN7984
M4 x 8 DIN7984
D5 Version:
DDC Version:

- 12 -
STEP 1
Position the bracket onto the reservoir and make sure that holes
are aligned (as shown on the picture). Tighten the M4 x 8 DIN7984
Screws using M2.5 Allen Key. Tighten the screws evenly.
STEP 1
INSTALLING EK-QUANTUM KINETIC FLT USING UNI PUMP BRACKET
ATTACHING EK-QUANTUM KINETIC FLT WITH SUPPLIED MOUNTS
3a.
Included M4 nuts, washers and M4 x 10 screws can be used to
mount the flat reservoir to a fan.
M4 x 8 DIN7984
UNI PUMP BRACKET
M4 x 10 DIN7984
M4 Washer
M4 Nut

- 13 -
3b.
Using 30 mm long screws supplied with your radiator the reservoir
can be mounted onto the radiator and 25 mm thick fans together.
UNC 6-32 x 30
ISO 7380 Screw
3c.
Alternatively the shorter 5mm long screws from the radiator may be
used to mount only the reservoir.
UNC 6-32 x 5 ISO
7380 Screw

- 14 -
ATTACHING THE FITTINGS
EK-Quantum Kinetic FLT has two inlet and two outlet ports, one of
each must be used!
All the unused ports should be blocked using G1/4 plugs!
*Optional
INLET*
DRAIN
F I L L*
OUTLET*
3d.
Lastly the supplied M4 nuts, washers and M4 x 10 screws may be
used to secure the reservoir to a case with the mounts. This is useful
when there is no clearance behind for the pump or to prevent all
airflow being blocked.
M4 x 10 DIN7984
M4 Washer
M4 Nut

- 15 -
CONNECTING THE D-RGB LED STRIP
STEP 1
Plug the 3-pin connector from Water block’s D-RGB LED light to
the D-RGB HEADER on the motherboard. The LED will work if the
pin layout on the header is as follows: +5V, Digital, empty, Ground.
Please ensure that the arrow indicated on the connector
is the plugged into the +5V line as indicated on your
motherboard. Failure to do so will damage your
motherboard or the LED strip.
STEP 1
D-RGB HEADER
RGB HEADER
To ensure the installation of EK components was successful, we
recommend you perform a 24-hour leak test.
When your loop is complete and filled with coolant, connect the
pump to a PSU outside your system. Do not connect power to any
of the other components. Turn on the PSU and let the pump run
continuously. It is normal for the coolant level to drop during this
process as air collects in the reservoir.
Inspect all parts of the loop, and in case the coolant leaks, fix the issue
and repeat the testing process. To prevent possible damage, please
ensure that all hardware is dry before the system is powered on.
TESTING THE LOOP

In case you need assistance or wish to order spare parts or a new
mounting mechanism, please contact:
https://www.ekwb.com/customer-support/
For spare parts orders, refer to the page with “TECHNICAL
SPECIFICATIONS AND PRODUCT PARTS” where you can find the
EAN number of each part you might need.
Include the EAN number with quantity in your request. Mounting
Mechanism EAN can be found under “BOX CONTENTS”.
Thermal pads are readily available in the EK shop
EKWaterBlocks
@EKWaterBlocks
ekwaterblocks
ekwaterblocks
EKWBofficial
SUPPORT AND SERVICE
SOCIAL MEDIA