EK-Quantum Monoblock Series User manual

USER GUIDE
EKQuantum
Momentum ROG Strix X570-E D-RGB
MONOBLOCK

This product is intended for installation only by expert users.
Please consult with a qualified technician for installation. Improper
installation may result in damage to your equipment. EK Water Blocks
assumes no liability whatsoever, expressed or implied, for the use of
these products, nor their installation. The following instructions are
subject to change without notice. Please visit our web site at www.
ekwb.com for updates. Before installation of this product please
read important notice, disclosure and warranty conditions printed
on the back of the box.
Before you start using this product please follow these basic guidelines:
Please carefully read the manual thoroughly before beginning
with the installation process!
Please remove your motherboard from the computer to assure
safest mounting process in order to prevent any possible
damages to your CPU and/or motherboard’s circuit board (PCB).
The EK- Fittings require only a small amount of force to screw
them firmly in place since the liquid seal is ensured by the
rubber o-ring gaskets.
The use of quality, market proved corrosion inhibiting coolants
is always strongly recommended for any liquid cooling system.

- 3 -
TABLE OF CONTENT
PREPARING YOUR MOTHERBOARD 4
REMOVING STOCK COOLER 4
REMOVING OF THE ORIGINAL PLASTIC HOLDDOWN AND THE FACTORY BACKPLATE 5
APPLYING THERMAL COMPOUND 6
CUTTING THERMAL PADS 6
PLACING THERMAL PADS ON THE MOTHERBOARD 6
PLACING THE BLOCK ON TO MOTHERBOARD 7
ATTACHING BLOCK ON THE MOTHERBOARD 7
CONNECTING THE DRGB LED STRIP 8
REQUIRED TOOLS 9
SUPPORT AND SERVICE 10
SOCIAL MEDIA 10

- 4 -
PREPARING YOUR MOTHERBOARD
REMOVING STOCK COOLER
Remove all encircled screws. There are screws on the back of the
motherboard, that needs to be removed in order to remove the
factory installed MOSFET cooling solution. Additional screws need
to be removed to remove I/O cover. You can attach the I/O cover
back, after you mount the Monoblock.
I/O Cover screws
Mosfet screws

- 5 -
REMOVING OF THE ORIGINAL PLASTIC
HOLDDOWN AND THE FACTORY
BACKPLATE
Using Philips-head screwdriver remove the four(4) UNC 6-32 screws
securing the original plastic hold-down clamps around the socket as
shown on the sketch. Remove the original backplate and the hold-
down clamps.
UNC 6-32 Screws
Factory
Backplate

- 6 -
APPLYING THERMAL COMPOUND
Apply thermal compound on CPU heat spreader (IHS) with enclosed
EK-TIM Ectotherm thermal grease. The quantity of about two rice
grains is just about right. There is no need to cover the whole IHS.
Applying too much thermal grease will have negative impact on the
cooling performance!
CUTTING THERMAL PADS
Your block comes with thermal pads which needs to be trimmed
in order to fit the voltage regulation area (MOSFET) on the
motherboard’s circuit board.
1. Thermal PAD F 1,0mm - (120x16mm) EAN: 3830046996732
WARNING: Dimensions on pictures below are scaled.
PLACING THERMAL PADS ON THE
MOTHERBOARD
Place thermal pads on PCB as shown on the picture.
Please remove the protective foil from both sides of the
thermal pads prior to installation!
Thermal Pad F – 1.0 mm
16
120
Thermal Pad F 1.0mm

- 7 -
PLACING THE BLOCK ON TO MOTHERBOARD
Place the EK-Quantum Momentum ROG Strix X570-E Monoblock
series water block to the motherboard or vice versa (as shown on the
photo). Make sure that mounting holes are aligned.
ATTACHING BLOCK ON THE MOTHERBOARD
STEP 1
Prior to fastening the screws please make sure the mounting holes
on the motherboard’s circuit board are aligned with the water block.
Mosfet part: Use four(4) M2.5X5 AX1 screws with PVC washers.
Tighten the screws evenly. Do not use excessive force when
tightening the screws.
CPU part: Use four (4) M3X10 DIN 7984 with screws. Tighten the
screws using enclosed 2mm Allen Key.
Do not forget install the Backplate Insulator and AM4
Backplate (as shown on the photo).
STEP 1
PVC washer
M3X10 DIN7984 Screw
M2.5x5 AX1 Screw
Backplate
Insulator
AM4 Backplate

- 8 -
STEP 2
For the EK-Quantum Momentum ROG Strix X570-E Monoblock series
water block to operate properly the G1/4 port nearest to the right
edge of the water block MUST BE USED AS THE INLET PORT.
EK recommends the use of EK-Fittings. When using fittings other
than EK series please use hose clamps or appropriate substitute
to secure the tubing to the barb. The use of biocide containing and
corrosion inhibiting coolant is always recommended for any liquid
cooling system.
CONNECTING THE DRGB LED STRIP
Plug the 3-pin connector from Monoblock D-RGB LED strip to the
motherboard.
Please ensure that the arrow indicated on the connector is
plugged into the +5V line as indicated on your motherboard.
Failure to do so will damage your motherboard or LED strip.
STEP 2
D-RGB Header
RGB Header
IMPORTANT:
Use this opening
as an Inlet Port!

- 9 -
REQUIRED TOOLS
Phillips-head screwdriver Scissors
Allen Key

For assistance please contact:
http://support.ekwb.com/
EKWB d.o.o.
Pod lipami 18
1218 Komenda
Slovenia - EU
EKWaterBlocks
@EKWaterBlocks
ekwaterblocks
ekwaterblocks
EKWBofficial
SUPPORT AND SERVICE
SOCIAL MEDIA