EK-Quantum Vector Strix RTX 3090 Backplate User manual

USER GUIDE
EK-Quantum
Vector FE RTX 3090 D-RGB Active Backplate

This product is intended for installation by expert users only. Please
consult with a qualified technician. Improper installation may result
in damage to your equipment. EK assumes no liability whatsoever,
expressed or implied, for the use of this product or its installation. The
following instructions are subject to change without notice. Please, read
the manual carefully before beginning with the installation process. For
updates, you can visit our official website www.ekwb.com.
Before you start using this product, please follow these basic
guidelines:
Carefully read the manual before beginning the installation
process.
Remove your graphics card from the computer for the safest
mounting process to prevent any possible damage to your GPU
or its circuit board (PCB).
EK Fittings require only a small amount of force to screw them
firmly in place since the liquid seal is ensured with the rubber
O-ring gaskets.
The use of quality, market-proven, corrosion-inhibiting coolants
is always strongly recommended for any liquid cooling system.
Do not use pure distilled water as a cooling liquid! For best
results, EK recommends the use of EK-CryoFuel Coolants.
Make sure to bleed air out of your water block thoroughly in
order to reach optimal performance.
EK only guarantees compatibility with included EK-brand
thermal pads. The installation process, cooling performance,
and block contacts are tested exclusively with EK-brand
thermal pads. Listed thermal pad thicknesses apply only to
those included in the package.
EK does not guarantee compatibility with aftermarket
alternatives for thermal interface material.

- 3 -
TABLE OF CONTENTS
BOX CONTENTS 4
ACTIVE BACKPLATE DIMENSIONS 5
REQUIRED TOOLS 5
TECHNICAL SPECIFICATIONS AND PRODUCT PARTS 6
PREPARING THE 3090 FE WATER BLOCK 7
CUTTING AND PLACING THERMAL PADS 8
ATTACHING THE BACKPL ATE 9
CONNECTING THE D-RGB LED STRIP 11
SUPPORT AND SERVICE 12
SOCIAL MEDIA 12

- 4 -
Allen Key 2 mm (1 pc),
EAN: 8901
BOX CONTENTS
20 mm
20 mm
25 mm
25 mm
20 mm
20 mm
27 mm 27 mm
EK-Loop Multi Allen Key (1 pc),
EAN: 3830046996213
M3x25 DIN7991 Screw – Black (1 pc),
EAN: 9061
M3x25 DIN7991 Screw – Nickel (1 pc),
EAN: 104197
Allen Key 2.5 mm (1 pc),
EAN: 8902
M3x20 DIN7991 Screw – Black (2 pcs),
EAN: 8204
M3x20 DIN7991 Screw - Nickel (2 pcs),
EAN: 104196
M2.5x20 Screw – Black Chrome (4 pcs),
EAN: 104218
M2.5x20 Screw – Nickel (4 pcs),
EAN: 104219
EK-Quantum Vector FE RTX 3090 D-RGB Active Backplate
Terminal Screw M4x27 – Black Chrome
(2 pcs), EAN: 103398
Terminal Screw M4x27 – Nickel (2 pcs),
EAN: 103397
Thermal Pad F 1.0 mm (4 pcs),
EAN: 3830046996732
120 mm
16 mm

- 5 -
212.5 mm
121.5 mm
19.5 mm
40 mm
33.5 mm
62 mm
95 mm
46.5 mm
74.5 mm
12.5 mm
ACTIVE BACKPLATE DIMENSIONS
Phillips Head Screwdriver Scissors
REQUIRED TOOLS

- 6 -
TECHNICAL SPECIFICATIONS AND PRODUCT PARTS
Technical Specification:
- Dimensions (L x H x W): 212.5 x 121.5 x 40 mm
- D-RGB (Addressable RGB) Cable Length: 500 mm
- D-RGB LED Count: 24
- D-RGB Connector: Standard 3-Pin (+5V, Data, Blocked, Ground)
Position EAN Description Quantity
1100663 EK Badge 1
2104128 Top plate cover (Black elox) 1
104129 Top plate cover (Natural elox)
3104124 Top plexi 1
4104126 Main O-ring 1
5100815 LED Strip 1
6104131 Coldplate (Nickel) 1
79041N M3 x 11 DIN7991 (Ni) 13
9041 M3 x 11 DIN7991
85092
OR 12 x 1.5 2
99041N
M3 x 11 DIN7991 (Ni)
2
9041
M3 x 11 DIN7991
10 104133 Terminal insert (Nickel) 1
11 5158 OR 35 x 1.5 1
12 102639 EK-Plug G1/4 2
13 104123 AB Terminal 1
14 103398
Terminal screw (Black Chrome)
2
103397
Terminal screw (Nickel)
6
7
10
11
13
3
1
4
9
5
8
2
14
12

- 7 -
For this Step, you will need:
PREPARING THE 3090 FE WATER BLOCK
STEP 1
Unscrew the three (3) M3x12 DIN7991 screws and remove the backplate
cover, as shown in the image..
STEP 1
Allen Key 2 mm
M3 x 12
DIN7991
SCREW
BACKPLATE
COVER
For this Step, you will need:
STEP 2
After removing the backplate cover, four (4) backplate screws
needs to be removed. Detach the backplate as shown in the image.
Preinstalled thermal pads on the PCB also must be
detached. After removing the thermal pads, pre-applied
thermal grease also needs to be removed using a
nonabrasive cloth or Q-tip. EK recommends the use of
denatured alcohol for removing TIM leftovers.
STEP 2
M2.5 x 7 AX1 SCREWS
BAC KP L ATE
Phillips Head Screwdriver

- 8 -
STEP 3
EK-Quantum Vector FE 3090 Active Backplate comes with its own
terminal, meaning the original terminal on the EK-Quantum Vector
FE 3090 water block must be removed.
In case the EK-Quantum Vector FE 3090 water block is
already filled with coolant, empty the contents of the
water block before continuing with this step. Be careful
that the coolant that remained in the water block does
not contact the GPU!
For this Step, you will need:
Allen Key 2.5 mm
STEP 3
M4 x 24.5 DIN7984
SCREW
FC TERMINAL
STEP 1
Your Active Backplate comes with thermal pads that must be cut into
smaller pieces to cover all the VRM components. EK has included
more than enough thermal pads to complete the following Step(s).
Replacement thermal pads:
Thermal Pad F 1.0 mm – (120 x 16 mm) EAN: 3830046996732
STEP 1
Thermal Pad F – 1.0 mm (120 x 16 mm)
CUTTING AND PLACING THERMAL PADS
120 mm
16 mm
1 mm

- 9 -
STEP 2
STEP 2
Once cut to size thermal pads should be applied to the PCB as
shown in the image.
Thermal Pad F 1.0mm
ATTACHING THE BACKPLATE
STEP 1
For easier installation of the Active Backplate, the preinstalled
terminal and metal plate must be removed. Unscrew the two (2)
Terminal screws (as shown in the image) and remove the terminal.
Save the mention material for later use.
For this Step, you will need:
Allen Key 2.5 mm
STEP 1
AB TERMINAL
TERMINAL SCREW M4 x 27 DIN7984

- 10 -
M3x25 DIN7991
Screw (1 pc)
Allen Key
2 mm
M3x20 7991DIN
Screw (2 pcs)
M2.5x20
Screw (4 pcs)
STEP 3
STEP 3
Before attaching the terminal, make sure that four (4)
O-rings are IN terminal slots, as shown in the image.
20 mm
20 mm
25 mm
STEP 2
Place the active backplate on the PCB and make sure all holes are
aligned. Position the screws in each of the seven (7) mounting
holes (as shown in the image) and tighten them evenly with Allen
Key 2 mm.
STEP 2
M2.5 x 20
M3 x 20
DIN7991
M3 x 25 DIN7991
For this Step, you will need: