EK-Quantum Reflection2 PC-O11D XL D5 PWM D-RGB User manual

USER GUIDE
DISTRIBUTION PLATE
EKQuantum
Reflection2PC-O11D XL D5 PWM D-RGB

Before you start using this product please follow these basic guidelines:
Please carefully read the manual before beginning with the
installation process!
The EK Fittings require only a small amount of force to screw
them firmly in place since the liquid seal is ensured by the
rubber O-ring gaskets.
The use of corrosion inhibiting coolants is always recommended
for any liquid cooling system. EKWB recommends any of the
EKCryofuel for worry-free usage.

- 3 -
TABLE OF CONTENT
BOX CONTENTS 4
DISTRIBUTION PLATE DIMENSIONS 5
TECHNICAL SPECIFICATIONS AND PRODUCT PARTS 6
PREPARING THE 011D XL CHASSIS 7
PREPARING AND INSTALLING THE DISTRIBUTION PLATE 10
RECOMMENDED DISTRIBUTION PLATE CONFIGURATIONS 12
ATTACHING THE PUSH-IN ADAPTER (OPTIONAL) 14
CONNECTING THE D-RGB LED STRIP 15
CONNECTING THE PUMP 15
TESTING THE LOOP 16
SUPPORT AND SERVICE 17
SOCIAL MEDIA 17

- 4 -
BOX CONTENTS
8 mm
EK-Quantum Reflection2PC-O11D
XL D5 PWM D-RGB
Screw M4 x 8 DIN7984 (2 pcs)
Allen Key 2.5 mm (1 pc)M4 Nut (2 pcs)
Allen Key 2 mm (1 pc) Replacement bottom Radiator bracket (1 pc)
EK-Loop Multi Allen Key
Mounting Mechanism EAN: 105250

- 5 -
DISTRIBUTION PLATE DIMENSIONS
375.5 mm
174.9 mm
244.9 mm
404.9 mm
129.4 mm
150.5 mm
93.5 mm
195.5 mm
106.1 mm
224.6 mm
161.8 mm
165 mm
109.1 mm
154.6 mm
262.3 mm
293.5 mm
321.3 mm
53.1 mm
181.2 mm
19.7 mm
446 mm
77.8 mm
28.7 mm
44.4 mm
213.8 mm
51 mm
471.9 mm

- 6 -
TECHNICAL SPECIFICATIONS AND PRODUCT PARTS
11
10
27
16
2
1
20
23
24
14
5
3
17
25
15
13
8
12
9
6
4
19
18
26
22 21
7
Technical Specification:
Dimensions with the attached pump (W x D x H): 215.1 x 77.8 x 471.9 mm
– D-RGB LED count:
– D-RGB cable length: 500 mm
– D-RGB connector standard 3-pin (+5V, Data, Blocked, Ground)
Position EAN Description Quantity
1104634 TOP Plexi -(Block part) 1
2104635 TOP Plexi (Lid part) 1
3104639 LED Cover (Black e.) 1
4104642 Metal plate (Black) 1
5104644 Metal holder (Black) 2
6104599 Mylar sticker 2
7100663 EK - Badge 2
89061
Screw M3 x 25 DIN7991 5
99017
Screw M3 x 18 7991DIN 2
10 9023 Screw M4 x 6 DIN7984 4
11 8312 Screw M4 x 16 DIN7991 64
12 8311 Screw M4 x 20 DIN7984 4
13 101803 Pump holder 1
14 5154 OR 52 x3 NBR50 1
15 3831109813898 EK D5 Pump 1
16 102639 EK - Plug G1/4 14
17 104697 OR - 438 x 2 mm 1
18 104698 OR -105 x 2 mm 1
19 104699 OR - 90 x 2 mm 1
20 104700 OR -140 x 2 mm 1
21 104701
OR -77 x 2 mm 1
22 104702
OR -61 x 2 mm 1
23 104703 OR - 85 x 2 mm 1
24 104704 OR -65 x 2 mm 1
25 100815 LED D-RGB strip 800/600 mm 1
26 3831109895313 Push in adapter 6
27 3831109834282 Plug cover (Acetal) 14

- 7 -
PREPARING THE 011D XL CHASSIS
Before installing the distribution plate, carefully read
the PC case manual.
STEP 1
Unscrew the factory provided screws and remove the top panel
from the case.
STEP 2
STEP 2
Remove both side panels and the front panel from the case.
STEP 1

- 8 -
STEP 3
STEP 3
The SSD Trays also need to be removed from the back side of
the chassis. Once the distribution plate is secured they can be
reinstalled as required.
STEP 4
Unscrew the 2(two) marked factory screws and remove the bottom
Radiator bracket.
STEP 4
Factory Screws

- 9 -
STEP 5
STEP 5
From the original bottom Radiator bracket, remove two (2) marked
plastic tabs attached by four (4) cross pattern screws.
Plastic tabs and screws reattach to the replacement
bottom Radiator bracket and secure them with Philips
head screwdriver. Tighten the screws evenly.
After securing the distribution plate, replacement bottom
Radiator bracket can be installed with the bottom radiator
and fans.
PLASTIC TABS
ORIGINAL
BRACKET
REPLACEMENT
BRACKET

- 10 -
STEP 2
Carefully place the EK-Quantum Reflection PC-O11D XL D5 PWM
D-RGB distribution plate into the PC case and align the mounting
holes.
STEP 2
PREPARING AND INSTALLING THE DISTRIBUTION PLATE
STEP 1
Before installing the distribution plate, unscrew two (2) M3 x 18
DIN7991 Screws and remove the metal plate. Save the removed
parts for later steps.
STEP 1
M3 x 18 DIN79991
SCREW
METAL PL ATE For this step you will need:
Allen Key 2 mm

- 11 -
STEP 4
STEP 4
After the distribution plate is secured, the stored metal plate can
be reattached using two (2) M3 x 18 DIN7991 Screws. Tighten the
screws evenly.
M3 x 18
DIN79991
SCREW
METAL PL ATE
For this step you will need:
Allen Key 2 mm
STEP 3
STEP 3
Secure the distribution plate to the chassis with two (2) M4 x 8
DIN7984 and M4 nuts (as shown in the diagram).
M4 NUT
SCREW
M4 x 8
DIN7984

- 12 -
RECOMMENDED DISTRIBUTION PLATE CONFIGURATIONS
SIDE RADIATOR
INLET
TOP RADIATOR
INLET
BOTTOM
RADIATOR
OUTLET
SIDE RADIATOR
OUTLET
CPU OUTLET
CPU INLET
FILL
TOP RADIATOR OUTLET
(DOUBLE RADIATOR
CONFIGURATION)
TOP RADIATOR OUTLET
(TRIPLE RADIATOR
CONFIGURATION)
GPU INLET
GPU OUTLET
DRAIN
BOTTOM
RADIATOR
INLET
To complete your loop, all ports must be used as marked in the
image.
All remaining unused ports must be closed with supplied plugs,
using the EK-Loop Multi Allen Key.
If one of the prescribed components will not be installed
(ie. bottom radiator or GPU block) then one INLET and
one OUTLET port must still be joined together in order
for this distribution plate to function!
Only one INLET and one OUTLET port for the GPU
connection can be used, while all other INLET and
OUTLET GPU ports must be closed with G1/4 plugs
(enclosed in the package).

- 13 -
FILL
DRAIN

- 14 -
ATTACHING THE PUSH-IN ADAPTER (OPTIONAL)
The push-in adapters can be attached to the marked places in the
diagram.
For easier installation of the push-in adapters, EK recommends to
lubricate the O-rings with a few drops of coolant or water.

- 15 -
CONNECTING THE D-RGB LED STRIP
Plug the 3-pin connector of the distribution plate D-RGB LED light
to the D-RGB HEADER on the motherboard. The LED will work if the
pin layout on the header is as follows: +5V, Digital, Empty, Ground.
D-RGB Header
RGB Header
CONNECTING THE PUMP
The EK-D5 PWM pump has two connectors.
1. SATA Connector: It must be connected directly to your PSU at all
times as it is used to power the pump.
2. 4-pin PWM fan: It can be connected to your motherboard’s
CPU_ Fan or designated water pump header. It can also be
connected to a controller. This cable is used to control and report
the rotational speed of the pump. If it’s not connected, the pump
will run at maximum speed (100% PWM).
SATA
CONNECTOR 4-PIN PWM FAN
CONNECTOR

- 16 -
To make sure the installation of EK components was successful, we
recommend you perform a leak test for 24 hours.
When your loop is complete and filled with coolant, connect the
pump to a PSU outside of your system. Do not connect power to
any of the other components. Turn on the PSU and let the pump
run continuously. It is normal for the coolant level to drop during this
process as air collects in the distribution plate.
Inspect all parts of the loop, and in the eventuality that coolant leaks,
fix the issue and repeat the testing process. Ensure that all hardware is
dry before the system is powered on in order to prevent any damage.
TESTING THE LOOP

In case you need assistance or wish to order spare parts or a new
mounting mechanism, please contact:
https://www.ekwb.com/customer-support/
For spare parts orders, refer to the page with “TECHNICAL
SPECIFICATIONS AND PRODUCT PARTS” where you can find the
EAN number of each part you might need.
Include the EAN number with quantity in your request. Mounting
Mechanism EAN can be found under “BOX CONTENTS”
Thermal pads are readily available in the EK shop
EKWaterBlocks
@EKWaterBlocks
ekwaterblocks
ekwaterblocks
EKWBofficial
SUPPORT AND SERVICE
SOCIAL MEDIA