EK-Quantum Vector Strix RTX 3070 Backplate User manual

USER GUIDE
GPU WATER BLOCK
EK-Quantum
Vector TUF RTX 3070

Before you start using this product, please follow these basic guidelines:
Carefully read the manual before beginning with the
installation process.
Remove your graphics card from the computer for the safest
mounting process to prevent any possible damage to your
GPU or its circuit board (PCB).
EK Fittings require only a small amount of force to screw
them firmly in place since the liquid seal is ensured with the
rubber O-ring gaskets.
The use of quality market-proven corrosion-inhibiting
coolants is always strongly recommended for any liquid
cooling system.
Do not use pure distilled water as a cooling liquid! For best
results, EK recommends the use of EK-CryoFuel Coolants.
Make sure to bleed air out of your water block thoroughly in
order to reach optimal performance.

- 3 -
TABLE OF CONTENTS
BOX CONTENTS 4
WATER BLOCK DIMENSIONS 5
TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS 6
PREPARING THE GRAPHICS CARD 7
REMOVING THE STOCK COOLER 7
CLEANING THE PCB 7
CUTTING AND PLACING THERMAL PADS 8
APPLYING THERMAL COMPOUND 9
INSTALLING THE WATER BLOCK 9
PLACING THE BLOCK ON THE GRAPHICS CARD 9
ATTACHING THE BLOCK TO THE GRAPHICS CARD 10
CHECKING FOR CONTACT 10
INSERTING THE GRAPHICS CARD INTO THE CHASSIS 11
FITTINGS AND TUBING 11
CONNECTING THE D-RGB LED STRIP 12
REPLACING THE LED STRIP (Optional) 12
TESTING THE LOOP 13
SUPPORT AND SERVICE 14
SOCIAL MEDIA 14

- 4 -
BOX CONTENTS
4 mm
4 mm
6 mm
8 mm
M3x4 DIN7985 Screw (2 pcs) EK-Loop Multi Allen Key (1 pc)
M2.5 Nut (6 pcs)
M2.5x6 AX1 Screw (13 pcs)
Allen Key 2.5 mm (1 pc) Thermal Pad F 1.0 mm (3 pcs)
Thermal Grease (1 pc)
M2.5x8 AX1 Screw (2 pcs)
M2.5x4 AX1 Screw (16 pcs)
EK-Quantum Vector TUF RTX 3070 D-RGB PVC Washer M2.5 (16 pcs)
120 mm
16 mm
EK-Plug G1/4 (2 pcs)
Universal Mounting Mechanism – You may not need every
screw from this package. EAN: 3831109872215

- 5 -
WATER BLOCK DIMENSIONS
254.5 mm
124.5 mm
153.5 mm
149 mm
134 mm
20.5 mm
19 mm

- 6 -
TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS
Technical Specification:
- Dimensions (L x H x W): 254.5 x 149 x 20.5 mm
- D-RGB cable length: 500 mm
- D-RGB LED count: 9
- D-RGB connector standard 3-pin (+5V, Data, Blocked, Ground)
Position EAN Description Quantity
1101743 Terminal cover + D-RGB LED 1
28311 M4 x 20 DIN7984 Screw 3
3101628 FC Terminal 1
45155 FC Terminal O-ring 15 x 1 mm 2
5103466 TOP Acetal - Stickout 1
6100663 EK - Badge 1
79013 M4 x 8 DIN7984 Screw 14
8103222
TOP Plexi - Vector TUF RTX 3070 1
9103567
TOP Plexi - Vector TUF RTX 3070 Insert 1
10 5115 Main O-Ring 144 x 2 mm 1
11 101254 Jet plate 1
12 103221 Coldplate 1
13 103114 M4/M2.5 x 10.50 Standoff 1
14 102696 M3.5/M2.5 x 2.5 Standoff 9
15 8533 M4/M2.5 x 2.5 Standoff 4
16 9049 M2.5 x 7 AX1 Screw 3
17 103468 TOP Acetal - Under Stickout 1
18 101290 D-RGB LED Strip 1
19 101076 Wire Harness 1
1
8
9
10
11
13
15
14
12
5
19
7
6
2
17
18
16
3
4
M4/2.5 x 2.5
STAN DOFF
M3.5/2.5 x 2.5
STAN DOFF
M3.5/2.5 x 2.5
STAN DOFF
M4/2.5 x 10.5
STAN DOFF

- 7 -
PREPARING THE GRAPHICS CARD
STEP 1
REMOVING THE STOCK COOLER
Place your graphics card on the flat surface and carefully remove the
stock cooler. Do not forget to unplug all the LED and fan connectors.
Pay attention to the following steps when installing EK-Quantum
Vector TUF RTX 3070 water block onto your graphics card.
STEP 2
CLEANING THE PCB
Wipe off the remains of the original thermal compound using a
nonabrasive cloth or Q-tip, as shown in the sample image, until the
components and circuit board are completely clean. EK recommends
the use of denatured alcohol for removing TIM leftovers. After that,
remove all remaining stock thermal pads from the PCB.
STEP 2

- 8 -
STEP 1
Your GPU water block comes with thermal pads that have to be cut
into smaller pieces to cover all the VRM components, such as COILs,
MOSFETs, and drivers.
You must remove the protective foil from both sides of the
thermal pad before installation.
Replacement thermal pads:
3x Thermal Pad F 1.0 mm – (120 x 16 mm) EAN: 3830046996732
STEP 1
Thermal Pad F – 1.0 mm (120 x 16 mm)
CUTTING AND PLACING THERMAL PADS
120 mm
16 mm
1 mm
STEP 2
STEP 2
Once cut to size, thermal pads should be placed on the PCB, as
illustrated below. EK made sure to provide you with more than an
adequate quantity of thermal pads to complete this Step.
Thermal Pad F 1.0 mm

- 9 -
Thermal Grease
STEP 1
Apply the enclosed EK-TIM Ectotherm thermal grease (thermal
compound) on the GPU heat spreader – IHS – as shown in the
image. The layer of the thermal compound must be thin and even
over the entire surface of the IHS.
The excessive or uneven application of thermal grease
may lead to poor performance!
STEP 1
APPLYING THERMAL COMPOUND
For this Step, you will need:
INSTALLING THE WATER BLOCK
STEP 1
PLACING THE BLOCK ON THE GRAPHICS CARD
This procedure is the same for all full-cover water blocks.
Carefully position the water block with preinstalled standoffs on
the graphics card. During this process, make sure you have aligned
mounting holes of the PCB with holes of the water block (same
applies to other tops).
Pay attention not to use too much force when pressing
the block down to the PCB since chip dies are prone
to cracking.
STEP 1

- 10 -
For this Step, you will need:
M 2.5 PVC Washer
(14 pcs)
M2.5 x 4 AX1
Screw (14 pcs)
Phillips Head
Screwdriver
4 mm
STEP 2
M2.5 x 4 AX1 SCREW
M2.5 PVC WASHER
STEP 2
ATTACHING THE BLOCK TO THE GRAPHICS CARD
Use fourteen (14) M2.5 x 4 AX1 Screws and fourteen (14) M2.5
PVC Washers. Tighten the screws evenly using the Phillips head
screwdriver. EK recommends you start tightening the screws
around the GPU core first and then continuing outward to prevent
damaging the GPU.
CHECKING FOR CONTACT
If necessary, temporarily remove the water block to check for uniform
surface contact between the block and components. Pay special
attention to the VRM section of the graphics card. Check whether
the water block makes contact with the intended integrated circuit.
Then repeat Steps from the previous section to re-attach the block.
In case you fail to obtain good contact, please check
again or contact our support service at
https://www.ekwb.com/customer-support/.

- 11 -
INSERTING THE GRAPHICS CARD INTO THE CHASSIS
Carefully lift your graphics card with the installed water block and
insert it into your PC’s motherboard PCIexpress expansion slot.
Please keep in mind that your graphics card is heavier than before it
was equipped with the water block.
You need to be very careful when handling the
graphics card. Avoid all unnecessary manipulation
of the water block assembly that might damage your
card or water block.
FITTINGS AND TUBING
STEP 1
Screw-in two (2) G1/4 threaded male fittings. Attach the liquid
cooling tubes and connect the water block to the cooling loop.
Do not forget to plug the remaining two openings with
enclosed EK-Plug G1/4 or its equivalent.
EK recommends using EK fittings with all EK water blocks.
CAUTION: When using connectors other than EK fittings,
pay special attention to the length of the fittings’ male G1/4”
thread – 5mm is the maximum G1/4” thread length allowed!
STEP 1
TUBING
EK- PLUG
G1/4
EK-FITTING

- 12 -
CONNECTING THE D-RGB LED STRIP
STEP 1
Plug the 4-pin D-RGB connector from the GPU water block to the
D-RGB Header on your motherboard or controller. The LED strip will
work only if the pin layout on the header is as follows: +5V, Data,
Empty, Ground.
Incorrect installation or installation to a wrong header can
damage to the LED strip or the header itself!
STEP 1
In case of replacing the D-RGB LED strip, three (3) M2.5 x 7 AX1
Screws must be removed using Phillips Head Screwdriver (as shown
in the picture).
STEP 1
STEP 1
D-RGB HEADER
RGB HEADER
REPLACING THE LED STRIP (Optional)
M2.5 x 7 AX1

- 13 -
To ensure the installation of EK components was successful, we
recommend you perform a 24-hour leak test.
When your loop is complete and filled with coolant, connect the pump
to a PSU outside your system. Do not connect power to any of the other
components. Turn on the PSU and let the pump run continuously.
Inspect all parts of the loop, and in case the coolant leaks, fix
the issue and repeat the testing process. To prevent possible
damage, please ensure that all hardware is dry before the system
is powered on.
TESTING THE LOOP

In case you need assistance or wish to order spare parts or a new
mounting mechanism, please contact:
https://www.ekwb.com/customer-support/
For spare parts orders, refer to the page with “TECHNICAL
SPECIFICATIONS AND WATER BLOCK PARTS” where you can find
the EAN number of each part you might need.
Include the EAN number with quantity in your request. Mounting
Mechanism EAN can be found under “BOX CONTENTS”
Thermal pads are readily available in the EK shop
EKWaterBlocks
@EKWaterBlocks
ekwaterblocks
ekwaterblocks
EKWBofficial
SUPPORT AND SERVICE
SOCIAL MEDIA