eKey Uno User manual

Quick Start Guide
rechargeable ngerprint
scanner, wireless

• ekey uno
• Rechargeable battery
• Torx screwdriver
• Charger
• Bottom cap
• Safety screw
• Screws for fastening the ekey uno to the mounting plate
• Screw anchors and screws for fastening the mounting plate to
the wall (screw variant)
Observe the enclosed Safety information.
Scope of delivery
Sensor
Mounting
plate
Rechargeable
battery
Cover
Activation
sensor
Light ring
Battery-operated variant
Operating the ekey uno

4
Attach the mounting plate - minimum height 110cm
3
1
Activate the Nuki Smart Lock
Follow the operating instructions for the Nuki Smart Lock and mount it
on the door lock on the inside of the door
2
Battery is charging
Battery is fully charged
CLICK
Glue variant* Screw variant
An adhesive foil is already
attached to the mounting
plate. Remove the base foil
and adhere the mounting
plate.
OR
Fully charge the ekey uno battery
Charging time max. 5hours
Dene the position for the ekey uno
Determine a suitable position outside for your ekey uno before you start
mounting it. Right next to the door, for example. It is IMPORTANT to note:
*According to the BLE wireless connection standard, the typical range is 10m. However, this can be
lower, depending on the installation situation and the type of door.
110 cm
You can only activate the system successfully with a fully charged battery.
The device must be easy to reach with one‘s hand.
The installation height of at least 110cm is
important for ergonomically correct operation and
must therefore be observed.
The ekey uno communicates wirelessly with the
door lock actuator. Both devices must therefore be
installed in close proximity* to one another.
Battery-operated variant

6
Fasten the ekey uno to the mounting plate
using the screws provided
7
Open the metal clamp and remove the bottom cap
5
Remove the cover from the ekey uno
Slide up and tilt to one side
Attach the mounting plate in the previously selected
mounting position. You can glue on the mounting plate or
x it with the supplied screw anchors and screws.
*NOTE ONTHE GLUEVARIANT:
Remove the entire base foil. Thoroughly clean the surface where the device is to
be mounted. Adhere the mounting plate only to a smooth, dry surface at room
temperature. Apply a large amount of pressure to the surface to adhere the
mounting plate.The bond only reaches maximum adhesive strength after 3days.
Only then can the mounting plate be fully loaded.
For further information, visit: www.ekey-uno.net/faq.

8
Insert the rechargeable battery and close the
metal clamp
Make sure the battery is fully charged before inserting it
9
Attach cover
Apply at an angle, tilt towards the middle and slide down
OPTIONAL:
Attach the safety screw to x the
rechargeable battery and protect it
against manipulation
ekey uno app
GETCONNECTED!
ekey uno
10
Download the app
You need the free ekey uno app for mobile devices to activate your ekey
uno with the Nuki Smart Lock and for user administration.
You can nd all the information about your ekey uno retrotting set
(functions of the app, videos on activation, etc.) on our website
www.ekey-uno.net.
Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and
other countries. Google Play and the Google Play logo are trademarks of Google LLC.
www.ekey-uno.net
Nuki Smart Lock
ekey uno app

ID350/734/0/684:
Version 2, 2020-08-12
Copyright © 2020 ekey biometric systems GmbH.
All content, artwork and ideas contained in this Quick Start Guide are subject
to applicable copyright laws. Any transmission, relinquishment or transfer of
this content or parts thereof to third parties requires the prior written consent
of ekey biometric systems GmbH.Translation of the original documentation.
www.ekey-uno.net | This document is not subject to updating.We reserve the right to make technical modications and change the product‘s appearance; any liability for errors and misprints is excluded.
Important signals
Operating the ekey uno
Close
Place nger on sensor,
wait until LEDs ash blue.
As soon as the LEDs ash
blue, remove your nger.
Place nger on sensor, wait
until LEDs ash blue. Place
nger on sensor again
while LEDs are ashing.
Critical battery level Connect ekey uno with
mobile device
Your device is equipped with an activation sensor to enable the long rechargeable
battery life of approx. 6months. The activation sensor is shown here with a blue
symbol.When operating the ekey uno, always ensure that you touch the activation
sensor. Otherwise the device remains disabled.
Place nger on sensor until
top right segment ashes.
Flashing red
www.ekey-uno.net
Open
Additional signals can be found in the FAQ area