EKF CompactPCI CB3-TONE Manual

[phone] | [email protected] | artisantg.com
-~
ARTISAN
®
~I
TECHNOLOGY
GROUP
Your definitive source
for
quality
pre-owned
equipment.
Artisan Technology
Group
Full-service,
independent
repair
center
with
experienced
engineers
and
technicians
on staff.
We
buy
your
excess,
underutilized,
and
idle
equipment
along
with
credit
for
buybacks
and
trade-ins
.
Custom
engineering
so
your
equipment
works
exactly as
you
specify.
•
Critical
and
expedited
services
•
Leasing
/
Rentals/
Demos
• In
stock/
Ready-to-ship
•
!TAR-certified
secure
asset
solutions
Expert
team
ITrust
guarantee
I
100%
satisfaction
All
tr
ademarks,
br
a
nd
names, a
nd
br
a
nd
s a
pp
earing here
in
are
th
e property of
th
e
ir
r
es
pecti
ve
ow
ner
s.
Find the EKF CB3-1-TONE at our website: Click HERE

CB3-TONE
Technical Information
CB3-TONE •
CompactPCI
®
USB 3.0 SuperSpeed Controller
Document No. 6860 • Ed. 4 • 31 August 2015

Technical Information CB3-TONE • CompactPCI® USB 3.0 Controller
Contents
AboutthisManual ........................................................... 3
EditionHistory......................................................... 3
RelatedDocuments ..................................................... 4
Nomenclature ......................................................... 4
TradeMarks .......................................................... 4
Legal Disclaimer - Liability Exclusion ......................................... 4
Standards ............................................................ 5
FeatureSummary ...................................................... 6
ShortDescription....................................................... 7
TheoryofOperation .................................................... 8
Hardware ....................................................... 8
PerformanceConsiderations ......................................... 8
BlockDiagram......................................................... 9
FrontPanel .......................................................... 10
SystemIntegration .................................................... 11
InstallingandReplacingComponents............................................ 12
BeforeYouBegin...................................................... 12
Warnings ...................................................... 12
Caution ....................................................... 12
InstallingtheBoardAssembly ............................................ 13
RemovingtheBoardAssembly............................................ 14
EMCRecommendations................................................. 16
Technical Reference - Connectors ............................................... 17
USB 3.0 Connectors ................................................... 17
J1 Backplane Connector ................................................. 18
Drivers ................................................................... 20
Schematics................................................................ 20
© EKF -2- ekf.com

Technical Information CB3-TONE • CompactPCI® USB 3.0 Controller
About this Manual
This manual is a short form description of the technical aspects of the CB3-TONE, required for
installation and system integration. It is intended for the advanced user only.
Edition History
Ed. Contents/Changes Author Date
1 Technical Information CB3-TONE, english, preliminary edition
Text #6860, File: cb3_ti.wpd
jj 11 October 2012
2 Added photos jj 15 February 2013
3 Augmented table ‘Feature Summary’ (reference to PXI) jj 11 April 2014
4 Revision 1 PCB - added illustration front panel (indicator LEDs),
added table 'Similar Products', added photo of sample hybrid system
jj 31 August 2015
© EKF -3- ekf.com

Technical Information CB3-TONE • CompactPCI® USB 3.0 Controller
Related Documents
Related Information
CB3-TONE Home www.ekf.com/c/cusb/cb3/cb3.html
Nomenclature
Signal names used herein with an attached '#' designate active low lines.
Trade Marks
Some terms used herein are property of their respective owners, e.g.
<CompactPCI, CompactPCI PlusIO, CompactPCI Serial: ® PICMG
<Windows: ® Microsoft
<EKF, ekf system: ® EKF
EKF does not claim this list to be complete.
Legal Disclaimer - Liability Exclusion
This document has been edited as carefully as possible. We apologize for any potential mistake.
Information provided herein is designated exclusively to the proficient user (system integrator,
engineer). EKF can accept no responsibility for any damage caused by the use of this manual.
© EKF -4- ekf.com

Technical Information CB3-TONE • CompactPCI® USB 3.0 Controller
Standards
Reference Documents
Term Document Origin
CompactPCI® CompactPCI Specification, PICMG® 2.0 R3.0, Oct. 1, 1999 www.picmg.org
CompactPCI®
PlusIO
CompactPCI PlusIO Specification, PICMG® 2.30 R1.0,
November 11, 2009
www.picmg.org
CompactPCI®
Serial
CompactPCI Serial Specification, PICMG® CPCI-S.0 R1.0,
March 2, 2011
www.picmg.org
PCI Express® PCI Express® Base Specification 3.0 www.pcisig.com
PCI Local Bus PCI 2.2/2.3/3.0 Standards PCI SIG www.pcisig.com
PXI® PCI eXtensions for Instrumentation
PXI Hardware Specification Rev. 2.2
www.pxisa.org/
USB Universal Serial Bus Specification 3.0 & 2.0 www.usb.org
xHCI eXtensible Host Controller Interface for Universal Serial Bus
(xHCI) Rev. 1.0 2010-05-21
www.intel.com
© EKF -5- ekf.com

Technical Information CB3-TONE • CompactPCI® USB 3.0 Controller
Technical Features
Feature Summary
Feature Summary
<CompactPCI® Peripheral Card 3U 4HP (single size Eurocard)
<Backplane connector J1 32-bit PCI 33/66MHz, +5V or +3.3V VIO (J1 w/o key)
<Internally based on PCI Express® technology (PCI to PCIe bridge)
<+5V only design
<Ready for usage within PXI® systems
<PCIe to quad-port USB 3.0 controller
<USB 3.0 xHCI (eXtensible host controller interface) SuperSpeed
<WHQL drivers available
<USB 2.0 high-speed, full-speed, low-speed supported
<4 x front panel USB 3.0 type A receptacles for attachment of external devices
<+5V/1.5A USB power switches
<Designed & manufactured in Germany
<ISO 9001 certified quality management
<Long term availability
<Coating, sealing, underfilling on request
<RoHS compliant
<Operating temperature: 0°C to +70°C • industrial temperature range on request
<Storage temperature: -40°C to +85°C, max. gradient 5°C/min
<Humidity 5% ... 95% RH non condensing
<Altitude -300m ... +3000m
<Shock 15g 0.33ms, 6g 6ms
<Vibration 1g 5-2000Hz
<MTBF tbd
<EC Regulations EN55022, EN55024, EN60950-1 (UL60950-1/IEC60950-1)
© EKF -6- ekf.com

Technical Information CB3-TONE • CompactPCI® USB 3.0 Controller
Short Description
The CB3-TONE is a CompacPCI® peripheral
card, equipped with a PCI Express® to USB 3.0
quad-port controller. Four USB 3.0 receptacles
are available via the front panel for attachment
of external USB 3.0 and USB 2.0 compliant
devices. Electronic power switches are provided,
for up to +5V/1.5A load at any USB connector.
The USB controller supports all data transfer
protocols on any connector, SuperSpeed (USB
3.0 xHCI) as well as high-speed, full-speed, and
low-speed. The CB3-TONE is provided with a
PCI® to PCI Express® bridge, as interface
between the USB controller and the
CompacPCI® backplane.
© EKF -7- ekf.com

Technical Information CB3-TONE • CompactPCI® USB 3.0 Controller
Theory of Operation
Hardware
The CB3-TONE is equipped with the TI
TUSB7340 single chip PCI Express® to USB 3.0
bridge. The xHCI (SuperSpeed) compliant host
controller supports up to four downstream
ports. Each downstream port may be
independently enabled and has individual
power control and overcurrent detection.
SuperSpeed USB 3.0 offers ten times the data
speed of USB 2.0 (5 Gbit/s compared to 480
Mbit/s). The bandwidth of the xHCI controller is
shared over all TUSB7340 downstream ports.
Texas Instruments provides xHCI compliant
Windows® drivers for download at
www.ti.com/product/tusb7340#toolssoftware.
Performance Considerations
As with any CompactPCI® Classic peripheral
card, the backplane bandwidth is the limiting
parameter if performance is discussed. Up to
~2Gbps data throughput is available across a
32-bit CompactPCI® backplane @66MHz. The
data rate of a SuperSpeed USB port however is
rated at 5Gbps. As a result, the maximum
performance which can be achieved with the
CB3-TONE is significantly higher than with
previous USB 2.0 solutions, but considerably
below the USB 3.0 maximum.
As an alternate for applications which require
optimum performance, you might consider a
similar peripheral card based on CompactPCI®
Serial (www.ekf.com/s/serial.html).
Beyond the bandwidth discussion, the
CB3-TONE is a reliable and economic USB 3.0
controller card, which can be simply integrated
in any industrial CompactPCI® system.
© EKF -8- ekf.com

Technical Information CB3-TONE • CompactPCI® USB 3.0 Controller
Block Diagram
Front
Panel
I/O
Simplified Block Diagram
CB3-TONE
USB 3.0 Controller
PCI
PCIe
to
PCIe
Backplane
CompactPCI
PCI
8112
to
PCIe
USB 3.0
Power
Switch
Quad Port
Controller
xHCI
Power
Switch
USB 3.0 SuperSpeed
USB 2.0 High/Full/Low
© EKF -9- ekf.com

Technical Information CB3-TONE • CompactPCI® USB 3.0 Controller
© • •EKF draft - do not scale ekf.com
CB3-TONE R.1
2
3
USB 3.0
4
1
© EKF • draft - do not scale • ekf.com
CB3-TONE
2
3
USB 3.0
4
1
Front Panel
Two bicolour LED indicators (PCB Rev. 0) or 4 green LEDs (Rev. 1 PCB) are provided as USB VBUS (+5V)
indicator, associated to the particular receptacles. Since VBUS is controlled by the USB driver software,
the LEDs are lit when a connector is ready for use. Vice versa, a LED is off if the respective USB port is
not initialized, intentionally switched off, or a short-circuit situation is detected, presented by the
connected device.
© EKF -10- ekf.com

Technical Information CB3-TONE • CompactPCI® USB 3.0 Controller
CB3-TONE (2nd from left) in a Sample Hybrid System
System Integration
Similar Products
SB3-TONE CompactPCI® Serial USB Controller www.ekf.com/s/sb3/sb3.html
EB3-TONE CompactPCI® Express USB Controller www.ekf.com/e/eb3/eb3.html
© EKF -11- ekf.com

Technical Information CB3-TONE • CompactPCI® USB 3.0 Controller
Installing and Replacing Components
Before You Begin
Warnings
The procedures in this chapter assume familiarity with the general terminology associated with
industrial electronics and with safety practices and regulatory compliance required
for using and modifying electronic equipment. Disconnect the system from its
power source and from any telecommunication links, networks or
modems before performing any of the procedures described in this chapter. Failure
to disconnect power, or telecommunication links before you open the system or perform any
procedures can result in personal injury or equipment damage. Some parts of the system can continue
to operate even though the power switch is in its off state.
Caution
Electrostatic discharge (ESD) can damage components. Perform the procedures
described in this chapter only at an ESD workstation. If such a station is not available,
you can provide some ESD protection by wearing an antistatic wrist strap and
attaching it to a metal part of the system chassis or board front panel. Store the board
only in its original ESD protected packaging. Retain the original packaging (antistatic bag and
antistatic box) in case of returning the board to EKF for repair.
© EKF -12- ekf.com

Technical Information CB3-TONE • CompactPCI® USB 3.0 Controller
Installing the Board Assembly
Warning
This procedure should be done only by qualified technical personnel. Disconnect the system from its
power source before doing the procedures described here. Failure to disconnect power, or
telecommunication links before you open the system or perform any procedures can result in personal
injury or equipment damage.
Typically you will perform the following steps:
CSwitch off the system, remove the AC power cord
CAttach your antistatic wrist strap to a metallic part of the system
CRemove the board packaging, be sure to touch the board only at the front panel
CIdentify the related CompactPCI slot (peripheral slot for I/O boards, system slot for CPU boards,
with the system slot typically most right or most left to the backplane)
CInsert card carefully (be sure not to damage components mounted on the bottom side of the
board by scratching neighboured front panels)
CA card with onboard connectors requires attachment of associated cabling now
CLock the ejector lever, fix screws at the front panel (top/bottom)
CRetain original packaging in case of return
© EKF -13- ekf.com

Technical Information CB3-TONE • CompactPCI® USB 3.0 Controller
Removing the Board Assembly
Warning
This procedure should be done only by qualified technical personnel. Disconnect the system from its
power source before doing the procedures described here. Failure to disconnect power, or
telecommunication links before you open the system or perform any procedures can result in personal
injury or equipment damage.
Typically you will perform the following steps:
CSwitch off the system, remove the AC power cord
CAttach your antistatic wrist strap to a metallic part of the system
CIdentify the board, be sure to touch the board only at the front panel
Cunfasten both front panel screws (top/bottom), unlock the ejector lever
CRemove any onboard cabling assembly
CActivate the ejector lever
CRemove the card carefully (be sure not to damage components mounted on the bottom side
of the board by scratching neighboured front panels)
CStore board in the original packaging, do not touch any components, hold the board at the
front panel only
Warning
Do not expose the card to fire. Battery cells and other components could explode
and cause personal injury.
© EKF -14- ekf.com

Technical Information CB3-TONE • CompactPCI® USB 3.0 Controller
EMC Recommendations
In order to comply with the CE regulations for EMC, it is mandatory to observe the following rules:
CThe chassis or rack including other boards in use must comply entirely with CE
CClose all board slots not in use with a blind front panel
CFront panels must be fastened by built-in screws
CCover any unused front panel mounted connector with a shielding cap
CExternal communications cable assemblies must be shielded (shield connected only at one end
of the cable)
CUse ferrite beads for cabling wherever appropriate
CSome connectors may require additional isolating parts
© EKF -15- ekf.com

Technical Information CB3-TONE • CompactPCI® USB 3.0 Controller
Technical Reference - Connectors
USB 3.0 Connectors
The CB3-TONE is equipped with four front panel receptacles for USB 3.0 or USB 2.0 type A cable
connectors (USB root hub). When connected to USB 2.0 compliant devices, only the classic 4 contacts
(data pair, +5V and GND) are in use. USB 3.0 devices in addition communicate via the SuperSpeed
differential transmit and receive signal pairs, available across another 5 contact pins.
USB 3.0 Receptacles
1V
BUS +5V 1.5Amax
2USBD-
3USBD+
4GND
5 SS RX-
6 SS RX+
7GND
8 SS TX-
9 SS TX+
Each connector provides +5V (VBUS) for powering external devices. Electronic switches limit the
maximum output current of each individual USB connector to a safe level. The VBUS power has been
derived from the CompactPCI® +5V power rail via the backplane connector J1 and must be supplied
by the system power supply.
1
45
9
27
0
.23.
0
9
.1
© EKF • ekf.com
© EKF -16- ekf.com

Technical Information CB3-TONE • CompactPCI® USB 3.0 Controller
J1 Backplane Connector
A hard metric J1/P1 backplane connector is specified as by the PICMG® CompactPCI 2.0. A
mechanical key defines the VIO Voltage. The CE3-GIG is suitable for either +5V and +3.3V VIO, which
results in a 'no key' J1 connector. J1 conveys prominently the 32-bit PCI parallel bus.
1
25
J1 2
m
m
H
ard Metric Connector
© EKF 250.0525.10.01 ekf.com
abcdef
© EKF -17- ekf.com

Technical Information CB3-TONE • CompactPCI® USB 3.0 Controller
J1 A B C D E
25 5V REQ64# ENUM# 3.3V 5V
24 AD1 5V V(I/O) AD0 ACK64#
23 3.3V AD4 AD3 5V AD2
22 AD7 GND 3.3V AD6 AD5
21 3.3V AD9 AD8 M66EN C/BE0#
20 AD12 GND V(I/O) AD11 AD10
19 3.3V AD15 AD14 GND AD13
18 SERR# GND 3.3V PAR C/BE1#
17 3.3V IPMB SCL IPMB SDA GND PERR#
16 DEVSEL# GND V(I/O) STOP# LOCK#
15 3.3V FRAME# IRDY# BD_SEL# TRDY#
14
KEY AREA - No Key13
12
11 AD18 AD17 AD16 GND C/BE2#
10 AD21 GND 3.3V AD20 AD19
9C/BE3# GND AD23 GND AD22
8 AD26 GND V(I/O) AD25 AD24
7 AD30 AD29 AD28 GND AD27
6 REQ# GND 3.3V CLK AD31
5BRSVP1A5 BRSVP1B5 RST# GND GNT#
4IPMB PWR HEALTHY# V(I/O) INTP INTS
3 INTA# INTB# INTC# 5V INTD#
2TCK 5) 5V TMS TDO 1) TDI 1)
15V -12V TRST# +12V 5V
1) TDO - TDI internally connected
The CB3-TONE been designed for +5V only operation. Neither the +3.3V power pins nor +12V/-12V
are in use.
© EKF -18- ekf.com

Technical Information CB3-TONE • CompactPCI® USB 3.0 Controller
Drivers
For legacy operating systems such as Windows® 7 drivers must be installed first before taking the
advantage of SuperSpeed USB. Texas Instruments provides xHCI compliant Windows® drivers for
download at
www.ti.com/product/tusb7340#toolssoftware
The CB3-TONE does not support booting from an attached USB device. No TUSB7340 expansion BIOS
ROM is provided on-board. EKF offers boot code as part of the CPU UEFI firmware on request.
Schematics
Complete circuit diagrams for this product are available for customers on request. Signing of a non-
disclosure agreement would be needed. Please contact [email protected] for details.
EKF reserves the right to refuse distribution of confidential information material for any reason that
EKF may consider substantial.
© EKF -19- ekf.com