Elation Event Brick W System User manual

Rev. 5/01/2009 Software Ver 1.0
Event Brick W System
Elation Professional
6122 S. Eastern Ave.
Los Angeles, Ca. 90040
www.elationlighting.com

Event Brick System™
©Elation Professional® 2 Event Brick System™

Event Brick System™
©Elation Professional® 3 Event Brick System™
CONTENTS
1. General Information……………………………………………………………………… 4
a. Introduction………………………………………………………………………. 4
b. Unpacking………………………………………………………..………..…..… 4
c. Customer Support…………………………………………….………………… 4
d. Warranty Registration……………………………………………….……..…… 5
2. Safety Instructions………………………………………………………........…………. 6
3. Features……………………………………………………………………………………8
4. General Guidelines………………………………………………………………………. 9
5. Fixture Overview…………………………………………………………….…………… 10
6. Mounting and Installation………………………………………………………….……. 14
a. Yoke Assembly….……………………………………………..………………… 14
b. Mounting Points…………………………………………………………………. 16
c. Securing………………………………………………………………………….. 18
7. Understanding DMX……………………………………………………………………... 19
a. DMX X Cable Requirements...………………………………………………….19
b. DMX Terminator…………………………………………………………………. 21
c. 3-Pin to 5-Pin Conversion……………………………………………………….21
8. Fixture Menu……………………………………………………………………………… 23
a. Menu functions………………………………………………………………….. 23
9. DMX Addressing……...………………………………………………………………….. 26
10. Operation…………………………………………………………………………………. 28
11. Built-In Wireless Receiver……………………………………………………………… 30
12. Working with Built-In Programs……………………………………….……………….. 32
13. DMX Channel Traits…………………………………………………………………….. 38
14. Lens Replacement………………………………………………………………………..47
15. Cleaning and Maintenance……………………………………………………………… 48
16. Photometric Data………………………………………………………………………… 49
17. Dimensional Drawings………………………………………………….……………….. 50
18. Circuit Schematic………...……………………………………………………………….51
19. Battery Pack……………………………………………………………………………….52
20. Warranty…………………………………………………………………………………... 53
21. Technical Specifications…………………………………………...………….………… 55

Event Brick System™
©Elation Professional® 4 Event Brick System™
1. GENERAL INFORMATION
INTRODUCTION: Congratulations, you have just purchased one of the most innovative and
reliable lighting fixtures on the market today! The Event Brick System™ has been designed
to perform reliably for years when the guidelines in this booklet are followed. Please read
and understand the instructions in this manual carefully and thoroughly before attempting to
operate this unit. These instructions contain important information regarding safety during
use and maintenance.
UNPACKING: Thank you for purchasing the Event Brick System™ by Elation Professional®.
Every unit has been thoroughly tested and has been shipped in perfect operating condition.
Carefully check the shipping carton for damage that may have occurred during shipping. If
the carton appears to be damaged, carefully inspect your unit for damage and be sure all
accessories necessary to operate the unit have arrived intact. In the event damage has been
found or parts are missing, please contact our customer support team for further instructions.
Package contents included; 1 Event Brick, 1 battery pack, 1 battery Omega-clamp, 1 3-Pin
DMX cable, 1 safety cable, warranty card, and this user manual.
CUSTOMER SUPPORT: Elation Professional® provides a customer support line, to provide
set up help and to answer any question should you encounter problems during your set up
or initial operation. You may also visit us on the web at www.elationlighting.com for any
comments or suggestions. For service related issue please contact Elation Professional®.
Service Hours are Monday through Friday 9:00 a.m. to 5:00 p.m. Pacific Standard Time.
Please do not return this unit to your dealer without first contacting customer support at the
number listed below.
Voice: [phone]
Fax: [phone]
E-mail: [email protected]
Forum: www.ElationLighting.com/forum
Warning! To prevent or reduce the risk of electrical shock or fire, do not expose this unit to
rain or moisture.

Event Brick System™
©Elation Professional® 5 Event Brick System™
Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs
yourself, doing so will void your manufactures warranty.
Elation Encourages Recycling: Please do not discard the shipping carton in the trash.
Please recycle whenever possible.
WARRANTY REGISTRATION: The Event MH™ carries a two year (730 days) limited
warranty. Please fill out the enclosed warranty card to validate your purchase. All returned
service items whether under warranty or not, must be freight pre-paid and accompany a
return authorization (R.A.) number. The R.A. number must be clearly written on the outside
of the return package. A brief description of the problem as well as the R.A. number must
also be written down on a piece of paper and included in the shipping container. If the unit is
under warranty, you must provide a copy of your proof of purchase invoice. Items returned
without a R.A. number clearly marked on the outside of the package will be refused and
returned at customer’s expense. You may obtain a R.A. number by contacting customer
support at [phone].
Never open this fixture while in use!
This device falls under protection-class 1. Therefore it is essential that the device be
grounded properly.
Be sure the available voltage matches the voltage requirements of the unit.
Be sure the power cord is never crimped or damaged. If the power cord is damaged, replace
it immediately with a new one of similar power rating.
Always disconnect from main power before performing any type of service or any cleaning
procedure.
Only handle the power cord by the plug. Never pull out the plug by tugging the wire portion of
the cord.
Please be aware that damages caused by manual modifications to the device are not
subject to warranty.

Event Brick System™
©Elation Professional® 6 Event Brick System™
2. SAFETY INSTRUCTIONS
The Event MH™ is an extremely sophisticated piece of electronic
equipment. To guarantee a smooth operation, it is important to
follow the guidelines in this manual. The manufacturer of this
device will not accept responsibility for damages resulting from
the misuse of this fixture due to the disregard of the information
printed in this manual.
1. In the event the main power cord to this fixture becomes damaged, it should only be
repaired or replaced by Elation Professional, an authorized Elation service center,
or a similar qualified technician to prevent electrical hazard.
2. Always be sure that the fan and the air inlets remain clean and are never blocked.
Allow about 6” (15cm) between this fixture and other devices or a wall to allow for
proper cooling.
3. Never touch the fixture during normal operation. This can cause severe personal
injuries and/or damage to the fixture.
4. Be sure to unplug the EVENT BRICK™ from the power outlet before performing any
service related issues.
5. Never look directly into the light source. You risk injury to your retina, which may
induce blindness.
6. For safe operation, follow the Installation guide described in chapter two of this
manual. Operating the EVENT BRICK™ without suited safety aids such as safety
cables or clamps can increase the risk of damage and/or personal injury.
7. Installation should only be performed by qualified and certified personnel.
8. When mounting this fixture, use only the original rigging parts included with this
fixture. Any structural modification will void the original manufactures warranty and
may increase the risk of damage and/or personal injury.
9. To reduce the risk of fire or shock, do not expose this fixture to rain or moisture.
10. Do not attempt to operate this fixture if the power cord has become damaged or
frayed.

Event Brick System™
©Elation Professional® 7 Event Brick System™
11. Never charge the Battery and run the fixture on battery power at the same time.
This will damage the battery pack.
12. Never dispose of the battery pack in fire or incinerate, doing so may lead to
explosion.
13. When running the fixture with line voltage, be sure to disconnect the battery lead.
14. It is important to avoid overcharging and/or discharging. Be sure to charge the
battery immediately after use.
15. Charge the batteries, at least once, every six months during storage below 25˚C.
The period of this charge must be shortened to half by temperature rising in every
10˚C.
16. Avoid locating the batteries near a heat-generating device (such as a transformer)
or near fire. Do not locate the batteries near a device that may cause sparks, and
keep open flames from the battery at all times.
17. Do not place the batteries in an atmosphere of organic solvent or adhesive
materials.
18. Dismantling the battery is not advisable. If sulfuric acid is deposited on skin or
clothes, please wash well with sufficient amount of fresh water and obtain
immediate medical attention.
19. Fasten the batteries securely to protect it from abnormal vibration and shocks
during service.
20. Check the batteries for any sign of irregularities in appearance. If any damage such
as a crack and deformation, or electrolyte leakage is found on the case, cover, etc.,
the batteries must be replaced.
21. Do not short batteries. Do not attempt to disassemble the batteries. Avoid contact
with sulfuric acid leaked from the broken batteries.
Important Notice: Damages resulting from the disregard of safety and general user
instructions found in this user manual are not subject to any warranty claims.

Event Brick System™
©Elation Professional® 8 Event Brick System™
3. FEATURES
•Low power consumption
•Runs on Battery or Wall Voltage
•Wireless DMX Receiver Built-in
•Minimal heat emission
•Equipped with 12 one-watt LEDs: (4 red, 4 blue, 4 green)
•High quality Luxeon LEDs manufactured by Lumileds, USA
•100,000 hours RATED LEDs
•Smooth RGB additive color mixing, 16.7 million colors (24bit)
•Preprogrammed colored macros
•Strobe-effect with a maximum flash rate of 18fps (white or color)
•3, 4, 6, 12, or 15 DMX-channel operation
•Flicker-free operation for television and film
•Brilliant light output
•3 operation mode: DMX controlled, stand alone or sound activated (via internal
microphone)
•Dimmer intensity from 0%~100%
•Control board with 4-digit display and foil-keyboard
•Digital display can be turned 180° to fit different installation position
•RDMX (Remote DMX addressing from any DMX console)
•USITT DMX-512 Complaint
•Value of each DMX-channel can be displayed
•8 User Assignable Program Presets - Internal Program: Edit and save programs to
the incorporated EEPROM through the front control panel or external controller; you
can save a maximum of 48 scenes, and run the saved programs by using the “run”
menu on the front control panel

Event Brick System™
©Elation Professional® 9 Event Brick System™
4. GENERAL GUIDELINES
This fixture is a professional lighting effect designed for use on stage, in nightclubs, in
theatres, etc. Do not attempt operation or installation without a proper knowledge on how to
so.
This fixture was designed for indoor use only, use of this product outdoors will void all
warranties written or implied.
Although this fixture has not duty cycle, consistent operational breaks will ensure that the
fixture will function properly for many years to come.
Do not shake the fixture around. Avoid brute force when installing or operating the device.
When choosing an installation location, please be sure the fixture will not be exposed to
extreme heat, moisture, or dust. The minimum distance between the fixture and a wall or flat
surface should be at least .5 meter (about 1.5ft).
Always install the fixture with an appropriate safety cable. When installing the fixture in a
suspended environment always be to use mounting hardware no less than M10 x 25 mm,
also be sure the hardware is insert in the pre-arranged mounting holes in the bracket (see
page 17).
Do not attempt to operate this fixture until you have familiarized yourself with its functions.
Do not permit operation by persons not qualified for operating this type of theatrical fixture;
most damages are the result of operations by persons unfamiliar with this type of product.

Event Brick System™
©Elation Professional® 10 Event Brick System™
5. FIXTURE OVERVIEW
1. Hanging Bracket – The unit uses a unique sectional bracket that allows the unit to
be hung, mounted, or stood straight up.
2. LED Assembly/Diffusion Lens – One-watt Lumileds LED’s by Luxeon rated at
100,000 hours (4 red, 4 green, 4 blue). This lens is used to both protect the LEDs as