Elation POWER SPOT 700CMY II User manual

Revised 3/25/2008 visage Software version 1.5
POWER SPOT 700CMY II
User Manual

Power Spot 700CMY II™
©Elation Professional, Los Angeles Ca. 2 www.ElationLighting.com

Power Spot 700CMY II™
©Elation Professional, Los Angeles Ca. 3 www.ElationLighting.com
CONTENTS
1. General Information………………………………………………………………………4
a. Introduction……………………………………………………………………….4
b. Unpacking………………………………………………………..…………..….. 4
c. Customer Support…………………………………………….………………… 4
d. Warranty Registration……………………………………………………..…….5
e. Discharge Lamp Warning……………………………………………………… 5
2. Safety Instructions………………………………………………………........…………. 7
3. Features…………………………………………………………………………………...8
4. General Guidelines……………………………………………………………………….9
5. Fixture Overview………………………………………………………………………….11
6. Mounting and Installation………………………………………………………….……. 15
a. Mounting Positions……………………………………………………………… 15
b. Mounting Points………………………………………………………………….16
c. Securing…………………………………………………………………………..17
7. Understanding DMX……………………………………………………………………...18
a. DMX Cable Requirements……..………………………………………………. 18
b. DMX Terminator………………………………………………………………… 19
c. 3-Pin to 5-Pin Conversion……………………………………………………… 20
d. DMX Addressing…………………………………………………………………20
8. Fixture Menu………………………………………………………………………………22
a. Menu functions………………………………………………………………….. 23
9. Operation…………………………………………………………………………………. 34
10. DMX Channel Traits…...….…………………………………………………………….. 36
11. Lamp Installation………………………………………………………………………….43
a. Lamp optimization…………………………………………………..…………...44
12. Fuse Replacement………………………………………………………………………. 46
13. Optical Effects Module………………………………………………………………….. 47
14. Changing / Replacing Gobos & Colors………………………………………………... 50
a. Gobo Patterns…………………………………………………….…………….. 53
15. Animation Wheel………………………………………………………………………… 54
a. Animation Wheel Patterns..……………………………………………………. 56
16. Cleaning and Maintenance……………………………………………………………... 58
17. Warranty………………………………………………………………………………….. 60
18. Photometric Data………………………………………………………………………… 62
19. Dimensional Drawings………………………………………………….………………..63
20. Technical Specifications…………………………………………...………….…………64

Power Spot 700CMY II™
©Elation Professional, Los Angeles Ca. 4 www.ElationLighting.com
INTRODUCTION: Congratulations, you have just purchased one of the most innovative
and reliable lighting fixtures on the market today! The Power Spot 700CMY™, has been
designed to perform reliably for years when the guidelines in this booklet are followed.
Please read and understand the instructions in this manual carefully and thoroughly before
attempting to operate this unit. These instructions contain important information regarding
safety during use and maintenance.
UNPACKING: Thank you for purchasing the Power Spot 700CMY II™ by Elation
Professional®. Every Power Spot 700CMY II™ has been thoroughly tested and has been
shipped in perfect operating condition. Carefully check the shipping carton for damage that
may have occurred during shipping. If the carton appears to be damaged, carefully inspect
your unit for damage and be sure all accessories necessary to operate the unit have
arrived intact. In the event damage has been found or parts are missing, please contact
our customer support team for further instructions. Please do not return this unit to your
dealer without first contacting customer support at the number listed below.
CUSTOMER SUPPORT: Elation Professional® provides a customer support line, to
provide set up help and to answer any question should you encounter problems during
your set up or initial operation. You may also visit us on the web at
www.elationlighting.com for any comments or suggestions. For service related issue
please contact Elation Professional®. Service Hours are Monday through Friday 9:00 a.m.
to 5:00 p.m. Pacific Standard Time.
Voice: [phone]
Fax: [phone]
E-mail: [email protected]
Forum: www.ElationLighting.com/forum/
Warning! To prevent or reduce the risk of electrical shock or fire, do not expose this unit to
rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs
yourself, doing so will void your manufactures warranty.
Please do not discard the shipping carton in the trash. Please recycle whenever possible.

Power Spot 700CMY II™
©Elation Professional, Los Angeles Ca. 5 www.ElationLighting.com

Power Spot 700CMY II™
©Elation Professional, Los Angeles Ca. 6 www.ElationLighting.com
WARRANTY REGISTRATION: The Power Spot 700CMY II™ carries a two-year (730
days) limited warranty. Please fill out the enclosed warranty card to validate your
purchase. All returned service items whether under warranty or not, must be freight pre-
paid and accompany a return authorization (R.A.) number. The R.A. number must be
clearly written on the outside of the return package. A brief description of the problem as
well as the R.A. number must also be written down on a piece of paper and included in the
shipping container. If the unit is under warranty, you must provide a copy of your proof of
purchase invoice. Items returned without a R.A. number clearly marked on the outside of
the package will be refused and returned at customers’ expense. You may obtain a R.A.
number by contacting customer support at [phone].
DISCHARGE LAMP WARNING: This fixture is fitted with a
discharge lamp, which is highly susceptible to damage if
improperly handled. Never touch the lamp with your bare
hands, as the oil from your hands will shorten lamp life. Also,
never move the fixture until the lamps have had ample time to
cool. Remember, lamps are not covered under warranty
conditions.
This fixture emits intense UV radiation, which is harmful to the
eyes and skin. The intense luminance of the lamp can cause
severe damage to the retina. Never operate this fixture with the
protective covers removed, these covers have been specially designed to shield against
UV radiation.
Epileptic Warning: Those suffering from epilepsy should avoid looking directly into the
lamp at all times.
Avoid switching the fixture on and off repeatedly in short intervals, as this will reduce lamp
life and intensity.
To achieve the intensity associated with discharge lamps, these lamps use a gas sealed in
a high-pressure environment to emit a brilliant output. Due to the high pressure involved
with the construction of the lamp, the lamp may explode during prolonged extensive use.

Power Spot 700CMY II™
©Elation Professional, Los Angeles Ca. 7 www.ElationLighting.com
This risk is increased with age; added care is encouraged when dealing with older lamps.
Thus, lamp should always be replaced at the end of their recommended duty cycle.
Extreme caution should be used when operated this or any fixture fitted with a gas
discharge lamp.
Never open this fixture while in use!
During the initial operation of this fixture, a light smoke or smell may emit from the interior
of the fixture. This is a normal process and is caused by excess paint in the interior of the
casing burning off from the heat associated with the lamp.
This device falls under protection-class 1. Therefore it is essential that the device be
grounded properly.
Qualified personnel should perform all electrical connections.
Be sure the available voltage matches the voltage requirements of the unit.
Be sure the power cord is never crimped or damaged. If the power cord is damaged,
replace it immediately with a new one of similar power rating.
Always disconnect from main power before performing any type of service or any cleaning
procedure.
Only handle the power cord by the plug. Never pull out the plug by tugging the wire portion
of the cord.
Please be aware that damages caused by modifications to the device are not subject
to warranty.

Power Spot 700CMY II™
©Elation Professional, Los Angeles Ca. 8 www.ElationLighting.com
2. SAFETY INSTRUCTIONS
The Power Spot 700CMY II™ is an extremely sophisticated
piece of electronic equipment. To guarantee a smooth operation,
it is important to follow the guidelines in this manual. The
manufacturer of this device will not accept responsibility for
damages resulting from the misuse of this fixture due to the
disregard of the information printed in this manual.
1. Always be sure that the fan and the air inlets remain clean and are never
blocked. Allow about 6” (15cm) between this fixture and other devices or a wall to
allow for proper cooling.
2. Never touch the fixture during normal operation. This can cause severe
personnel injuries and/or damage to the fixture.
3. Be sure to unplug the POWER SPOT 700CMY II™ from the power outlet before
performing any service related issues.
4. Lamp Replacement; Allow at least 15 minutes after disconnecting main power
before you open the POWER SPOT 700CMY II™. To prevent personal injury,
never touch the lamp if you are not absolutely sure it has cooled.
5. Never look directly into the lamp beam. You risk injury to your retina, which may
induce blindness.
6. Be sure to track and record the lamp running time. The lamp should be changed
at the end of the specified lamp life, regardless of lamp output. You may also
have to change the lamp if it shows any deformations or damage. The same is
with all glass components, color filters, lenses and mirrors.
7. For safe operation, follow the Installation guide described in chapter two of this
manual. Operating the POWER SPOT 700CMY II™ without suited safety aids
such as safety cables or clamps can increase the risk of damage and/or personal
injury.
8. Qualified and certified personnel should only perform installation.
9. When mounting this fixture, use only the original rigging parts included with this
fixture. Any structural modification will void the original manufactures warranty
and may increase the risk of damage and/or personal injury.
10. To reduce the risk of fire or shock, do not expose this unit to rain or moisture.
11. Do not attempt to operate this fixture if the power cord is frayed or damaged.

Power Spot 700CMY II™
©Elation Professional, Los Angeles Ca. 9 www.ElationLighting.com
3. FEATURES
•Pan 530° / Tilt 285°
•3 operation mode: DMX controlled, stand alone or sound activated
•Electronic Power Supply (100v~240v / 50Hz~60Hz)
•Control board with 4-digit display
•Digital display can be turned 180° to fit different installation position
•CMY Subtractive Color Mixing
•Additional Color Wheel: 8 User replaceable colors
•2 Gobo Wheels:
oFixed: 9 plus open
oRotating: 7 User replaceable plus open
•Auto test for all functions
•Automatic Pan/Tilt Correction
•Glass Dichroic Reflector for Even Lamp Output
•Anti-Reflective Coated Lenses
•Brilliant MSR700/2 Lamp (700w, 1000Hrs, 7200K)
•USITT DMX-512 Complaint (3-pin and 5-pin DMX Connections)
•Ethernet Jack for Acrnet Protocol
•Value of each DMX-channel can be displayed
•Uses 24 DMX Channels (16-bit mode)
•Variable Frost Filter for Soft and Hard Edge Spot
•Variable Color Correction Filter
•3-Facet Prism
•Variable Animation Wheel
•User Replaceable Color and Gobos
•Intergraded Tilt Lock System
•Modular Construction
•Variable Zoom: 14˚~32˚ (Beam Angle)
•Motor Driven Focus
•Variable Iris (4%~100%)

Power Spot 700CMY II™
©Elation Professional, Los Angeles Ca. 10 www.ElationLighting.com
4. GENERAL GUIDELINES
This fixture is a professional lighting effect designed for use on stage, in nightclubs, in
theatres, etc. Do not attempt operation or installation without a proper knowledge on how
to do so.
This fixture was designed for indoor use only.
Consistent operational breaks may ensure that the fixture will function properly for many
years to come.
Do not shake the fixture around. Avoid brute force when installing or operating the device.
While choosing an installation location, please be sure that the fixture will not be exposed
to extreme heat, moisture or dust. The minimum distance between the fixture and a wall or
flat surface should be at least 0.5 meter (about 1.5ft).
Always install the fixture with an appropriate safety cable. When installing the fixture in a
suspended environment always be to use mounting hardware no less than M10 x 25 mm,
also be sure the hardware is insert in the pre-arranged screw holes in the base of the
fixture.
When using the quick release “Omega” cam-lock system, be sure the four quick lock
fasteners are locked in the quick lock holes correctly, see page 17 for more information on
the proper mounting procedures.
Do not attempt to operate this fixture until you have familiarized yourself with its functions.
Do not permit operation by persons not qualified for operating this type of theatrical fixture;
most damages are the result of operation by person unfamiliar with the operation of this
type of fixture.
If service is ever required, please use the original packaging to transport the fixture in for
service.

Power Spot 700CMY II™
©Elation Professional, Los Angeles Ca. 11 www.ElationLighting.com
Transportation and Handling
The POWER SPOT 700CMY II™comes with two carrying handles built into the base.
Always transport the fixture by these handles. Never lift or carry the POWER SPOT
700CMY II™ by the yoke (head assembly) this can seriously damage the unit and will void
your manufactures warranty.
Connections
Power supply:
Electronic ballast with:
90~260 Volts, 50~60 Hz,
Grounded contact type plug – Neutrik Powercon
Connected load 1000W <=> 4.5 A (blind current compensation).
NOTE: The universal power supply will accept any voltage source as detailed above
without any type of internal or user modifications.
DMX:
USITT DMX 512 Standard input/output, 3-pin and 5-pin XLR connectors.
3-pin: Pin 1 = [Ground] / Pin 2 = [-] / Pin 3 = [+]
5-pin: Pin 1 = [Ground] / Pin 2 = [-] / Pin 3 = [+] / Pin 4 = N.A. / Pin 5 = N.A.
Fuse Requirements:
The POWER SPOT 700CMY II’s electronic and lamp system are protected by two
GMA (5x20mm) external fuses:
Lamp: 250v/10A (120v Operation) or 250v/5A (220v Operation)
Electronics: 250v/2A (120v Operation) or 250v/1A (220v Operation)
The fuse requirements are clearly printed on the side of the fixture.
• Always disconnect main power before changing the fuse!
• Always replace with the exact same type fuse unless otherwise specified by an
authorized Elation® service technician. Replacing with anything other than the
specified fuse can severely damage your fixture and will void your manufactures
warranty.

Power Spot 700CMY II™
©Elation Professional, Los Angeles Ca. 12 www.ElationLighting.com
5. FIXTURE OVERVIEW
1. Moving Head
2. Carrying Handles
3. LED Menu Display
4. Head Tilt Lock
5. Omega Clamp
6. Ethernet Jack
7. 5-Pin DMX Out
Connector
8. 5-Pin DMX In
connector
9. Microphone
Sensitivity
10. Build-In Microphone
11. Software-Update
Connector
12. 3-Pin DMX Out
Connector
13. 3-Pin DMX In
Connector
14. Carrying Handle
15.Power On/Off
16.Lamp Fuse
17. Fan (air inlet/outlet)
18.Main Power Supply
(Powercon)
19.Electronics Fuse

Power Spot 700CMY II™
©Elation Professional, Los Angeles Ca. 13 www.ElationLighting.com
20.4-Segment LED Menu
Display
21. Mode Button
22. Enter Button
23. Up Button
24. Down Button
Side View - Menu and Display
1. Head Assembly – The head assembly consist of the main output lens, and either
the standard or CMY control module.
2. Carrying Handle – The fixtures includes two built-in carrying handles. Be sure to
always handle the fixture by the built-in carrying handles. Never lift or carry the
fixture by the head or retaining arms as this could cause serious damage to the
fixture and void your manufactures warranty.
3. 4-Segment Menu Display – This display details all the various menu functions.
See page 23 for a detailed breakdown of the operating menu.
4. Tilt Lock – This lock will hold the head assembly in place for transportation
and/or service. Depress the lock button to lock and unlock the head assembly.
The head will lock in a 90˚ or 45˚ orientation. Always be sure to unlock the head
assembly before applying main power to the unit. Failure to do so will result in a
start-up error and may damage the unit.
5. Omega Clamp - This fixture uses a cam-lock clamp system that allows a quick
and efficient means to secure a clamp to the unit. To attach a clamp to the unit,
attach a clamp that is rated to handle the weight of the unit to your omega clamp.
After a clamp has been attached to the omega clamp, attach the cam locks to the
designated position on the bottom of your unit. Lock the cam locks into position by
turning the wing nuts 90°. See page 17 for proper clamp mounting and assembly.
20
21
22
23
24

Power Spot 700CMY II™
©Elation Professional, Los Angeles Ca. 14 www.ElationLighting.com
6. Ethernet Jack – This jack is used for arcnet DMX protocol.
7. 5-PIN DMX Output Jack – This 5-Pin XLR jack is used to send an outgoing DMX
signal. For best results this jack should be terminated if it is the last fixture in a
DMX daisy-chain (see termination on page 20).
8. 5-Pin DMX Input Jack – This 5-Pin XLR jack is used to receive an incoming DMX
signal.
9. Microphone Sensitivity Adjustment Knob – This knob is used to adjust the
frequency sensitivity of the internal microphone when operating in “audio” mode.
When the knob is turned counter-clockwise the unit is less sensitive to sound.
When the knob is turned clockwise the unit is more sensitive sound.
10.Built-In Microphone – The built-in microphone is used to pick-up sound impulse
that are used to chase the built-in programs in Sound-Active control.
11.Firmware Connection – This connector is for use by an authorized technician
only. This connector is used to upgrade the operating software and to test the
fixture.
12.3-PIN DMX Output Jack – This 3-Pin XLR jack is used to send an outgoing DMX
signal. For best results this jack should be terminated if it is the last fixture in a
DMX daisy-chain (see termination on page 14).
13.3-PIN DMX Input Jack – This 3-Pin XLR jack is used to receive an incoming
DMX signal.
14.Carrying Handle – The fixtures includes two built-in carrying handles. Be sure to
always handle the fixture by the built-in carrying handles. Never lift or carry the
fixture by the head or retaining arms as this could cause serious damage to the
fixture and void your manufactures warranty.
15.Power Switch – The switch is used to control main power to fixture’s electronics.
16.Lamp Fuse Holder – This housing holds a 250v/10A GMA fuse (120v operation).
Never defeat this fuse. This fuse is designed to protect the lamp in the event of
severer power fluctuations. In the event of fuse failure, always be sure to replace
this fuse with an exact match unless otherwise instructed by an authorized Elation

Power Spot 700CMY II™
©Elation Professional, Los Angeles Ca. 15 www.ElationLighting.com
technician.
17.Internal Cooling Fan – This fixture is equipped with two high-velocity variable
speed fans mounted in the base to aid in the cooling process. These fans are
designed to vary their velocity at different operating temperatures. When the
fixture reaches a predetermined internal operating temperature the fans function
at high speeds. The higher speeds provide better cooling associated with higher
operating temperatures during long use. When the fixture is operating at a lower
temperature the fans operate at low speed. Be sure to keep all vents clean,
blocked cooling vents can shorten lamp life and reduce the fixtures reliability. For
more information on the fan functions see page 30, section 8.10.7.
18.Powercon Connector – This power jack is designed to be used only with the
Neutrik Powercon adapter included with your fixture. This jack provides main
power to your fixture.
19.Electronics Fuse Holder – This housing holds a 250v/2A GMA fuse (120v
operation). Never defeat this fuse, this fuse is designed to protect the electronics
in the event of severer power fluctuations. In the event of fuse failure, always be
sure to replace this fuse with an exact match unless otherwise instructed by an
authorized Elation technician.
20.4-Segment Menu Display – This display details menu functions.
21.Mode Select Button – This button is used to access the fixture’s main system
menu and on-board programming functions.
22.Enter Select Button – This button is used to select and confirm a menu function
when working in the fixture’s operating system.
23.Down Select Button – This button is used to scroll backwards when navigating
through the system menu.
24.Up Select Button - This button is used to scroll forward when navigating through
the system menu.

Power Spot 700CMY II™
©Elation Professional, Los Angeles Ca. 16 www.ElationLighting.com
6. MOUNTING AND INSTALLATION
Cautions:
For added protection mount the fixtures in areas outside walking paths, seating areas, or in
areas were unauthorized personnel might reach the fixture.
Before mounting the fixture to any surface, make sure that the installation area can hold a
minimum point load of 10 times the device’s weight.
Fixture installation must always be secured with a secondary safety attachment, such as
an appropriate safety cable.
MOUNTING
The POWER SPOT 700CMY II™ is fully operational in two different mounting positions,
hanging upside or set on a flat level surface. To avoid internal damage to the unit, never
mount the unit on its side as illustrated below. Be sure this fixture is kept at least 1.5 feet
away from any flammable materials (decoration etc.). Install a safety cable that can hold at
least 10 times the weight of the fixture. Never use the carrying handles for secondary
attachment.

Power Spot 700CMY II™
©Elation Professional, Los Angeles Ca. 17 www.ElationLighting.com
Refer to regulations BGV C1 (formerly VBG 70) and DIN VDE
0711-217 for proper installation in Europe
To ensure proper installation, only qualified staff should
attempt installation.
Mounting points
Overhead mounting requires extensive experience, including amongst others calculating
working load limits, a fine knowledge of the installation material being used, and periodic
safety inspection of all installation material and the fixture. If you lack these qualifications,
do not attempt the installation yourself. Improper installation can result in bodily injury.
CAUTION!
Be sure a qualified electrician performs all electrical
connections.
Be sure to complete all rigging and installation procedures before connecting the power
cord to the appropriate wall outlet.
Clamps
The POWER SPOT 700CMY II™ has been designed to hold multiple clamps to the bottom
of the unit in several different orientations. Always use an appropriately rated clamp to
mount this unit to truss. Refer to the printed instructions on the bottom of the fixture for
proper clamp installation.
a) Cam lock System: This system allows a quick and efficient means to
secure a clamp to the unit. To attach a clamp to the unit, attach a clamp
that is rated to handle the weight of the unit to your cam lock. After a clamp
has been attached to the cam lock, attach the cam locks to the designated
position on the bottom of your unit. Lock the cam locks into position by
turning the wing nuts 90°.

Power Spot 700CMY II™
©Elation Professional, Los Angeles Ca. 18 www.ElationLighting.com
90°
b) Be sure to always use two cam locks mounted to the bottom of unit to
ensure safe truss mounting (each two opposite threads max. M10x20).
Secure the POWER SPOT 700CMY II™
Regardless of the rigging option you choose for your POWER SPOT 700CMY II™ always
be sure to secure your fixture with a safety cable. The fixture provides a built-in rigging
point for a safety cable on the underside of the fixture, be sure to use this point and never
secure a safety cable to a carrying handle.

Power Spot 700CMY II™
©Elation Professional, Los Angeles Ca. 19 www.ElationLighting.com
7. UNDERSTANDING DMX
DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used by most
lighting and controller manufactures as a form of communication between intelligent
fixtures and controllers. DMX allows all makes and models of different manufactures to be
linked together and operate from a single controller. This is possible as long as all the
fixtures and the controller are DMX compliant. A DMX controller sends the DMX data
instructions to the fixture allowing the user to control the different aspects of an intelligent
light. DMX data is sent out as serial data that travels from fixture to fixture via data “IN” and
data “OUT” XLR terminals located on the fixtures (most controllers will only have output
jacks).
DMX Linking: To ensure proper DMX data transmission always use proper DMX cables
(not microphone cables) and a terminator. When using several DMX fixtures try to use the
shortest cable path possible. Never split a DMX line with a “Y” style connector. The order
in which the fixtures are connected in a DMX line does not influence the DMX addressing.
For example; a fixture assigned a DMX address of 1 may be placed anywhere in the DMX
chain, at the beginning, at the end, or anywhere in the middle. The DMX controller knows
to send data assigned to address 1 to that fixture no matter where it is located in the DMX
chain. The DMX address is set electronically using the controls on the LCD menu.
Data Cable (DMX Cable) Requirements (For DMX and Master/Slave Operation): Your
fixture and your DMX controller require a standard 3-pin or 5-pin XLR connector for data
input and data output (the figure on the next page is of a 3-Pin XLR connector). If you are
making your own cables, be sure to use two conductor shielded DMX cable rated at 120
ohms; this cable is designed for DMX transmission and may be purchased from your
Elation dealer or at most professional lighting retailers. Keep in mind that although
microphone cable may look similar to DMX cable it does not share the same resistance
rating and may be susceptible to line interference. Please always use proper DMX cables
for your data transmission. Your cables should be made with a male and female XLR
connector on either end of the cable. Also, remember that a DMX line must be daisy

Power Spot 700CMY II™
©Elation Professional, Los Angeles Ca. 20 www.ElationLighting.com
chained and cannot be split, unless using an approved DMX splitter such as the Elation
Opto Branch 4™ or DMX Branch/4™.
Be sure to follow the above figure when making your own cables. Do not use the ground
lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or
allow the shield conductor to come in contact with the XLR’s outer casing. Grounding the
shield could cause a short circuit and erratic behavior.
DMX-512 control connection
Connect the provided XLR cable to the female 3-pin XLR output of your controller and the
other side to the male 3-pin XLR input of the moving head (Please refer to the diagram
below.). You can chain multiple moving heads together through serial linking. The cable
needed should be two conductor, shielded cable with XLR input and output connectors.
Always be sure daisy chain your in and out data connections, never split or “Y” your DMX
connections unless you are using an approved DMX splitter such as the Elation Opto
Branch 4™ or DMX Branch/4™.
DMX-512 connection with DMX terminator
A DMX terminator should be used in all DMX lines especially in longer runs. The use of a
terminator may avoid erratic behavior in your DMX line. A terminator is a 120 ohm 1/4 watt