Elba EBM-9182 User manual

1
BLENDER
MODEL: EBM-9182
Owner’s Manual
Please read this manual carefully
before operating your set.
Retain it for future reference.
Record model number and serial
number of the set.
See the label attached on the set and
quote this information to your dealer
when you require service.
For The Warranty Terms & Conditions, Please Refer To Warranty Certificate.

2
IMPORTANT SAFEGUARDS
When using this appliance, basic precautions should always be followed, including
the following:
1. Read all instructions before using.
2. Do not operate the appliance with damaged power cord or plug, after the
appliance malfunction, or if it is dropped or damaged in any manner. Return the
appliance to the nearest authorized dealer or after-sales service center for
examination, repair, electrical or mechanical adjustment.
3. Do not use the appliance if the plug, the mains cord or other parts are damaged.
4. Do not let the power cord hang over edge of table or counter or hot surface.
5. Do not place the appliance on or near hot gas or electric burner, or in a heated
oven.
6. Do not leave the appliance unattended while operating.
7. Do not touch the cutting edges of the blender blade unit when you clean it. They
are very sharp and you could easily cut your fingers on them.
8. Do not operate the appliance for more than 3 minutes continuously at a time. If
you have not finished processing after 3 minutes, switch off the appliance and let it
cool down before you operate it again.
9. To prevent failure of the appliance, make sure that no food or liquids enter the
connection point between the blade unit interface and the motor base.
10. Never reach into the plastic blender with your fingers or an object while the
appliance is running.
11. Never use any accessories or parts from other manufacturers or that ELBA does
not specifically recommended.
12. Oversized foods or metal utensils must not be inserted into the appliance as they
may cause fire or risk of electric shock.
13. If foods stick to the wall of the blender, switch off the appliance and unplug it. Use
a spatula to remove the foods from the wall.
14. Always make sure the jar cover is properly closed/assembled on the plastic jar
and the lid is inserted properly in the jar cover before you switch on the appliance.
15. Never immerse motor base of the blender in water or any other liquids nor
rinse it under the tap. Use only a moist cloth to clean the motor base.
16. Close supervision is necessary when your appliance is being used near children
or infirm persons.
17. Always unplug the appliance before you assemble, dissemble or make adjustment
to any of the parts.
18. Do not operate the appliance for other than its intended use.
19. Do not use this blender outdoors.
20. This appliance is for domestic use only.
21. This appliance is not intended for used by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliances by a person responsible for their safety.
22. Children should be supervised to ensure that they do not play with the appliance.
23. Save these instructions for future reference.

3
PRODUCT DESCRIPTION
1. Lid
2. Jar cover
3. Plastic jar
4. Motor base
5. Control knob
6. Grinder
ASSEMBLE AND OPERATING THE APPLIANCE
1. Unpack the appliance and place it on a flat horizontal counter top. Check all the
parts whether all in good condition.
2. Clean the removable parts before using.
3. Make sure that the control knob is switched to “0” position.
4. Put the ingredients into the plastic blender.
5. Mount the lid onto the jar cover. Close the plastic jar with jar cover.
6. Insert the plastic jar onto the motor base and secure it tightly.
7. Power on the appliance and select the desired level of power.
8. Always switch off the appliance by setting the control knob to “0” position before
you open the jar cover.
9. Unplug the plug from wall outlet after use.

4
TIPS FOR BLENDER
Wash the foods (fruits, vegetable, etc.) that are to be blended (peel the skin or
remove pits when necessary). Cut them into pieces to be fit for blending.
Put the sliced foods into the plastic jar and put on the jar cover and lid.
Each time of blending, do not put more than half of the cup scale
(approximate 0.5 liter) of foods in it. Too small of a quantity is not preferable
either. Proper quantity of water should be added into during blending.
Power on the appliance and adjust the switch to speed “1” (low speed) or
speed “2” (high speed) position, the blender begins to work. It only takes
minutes to blend foods into small pieces. Then adjust the switch to “0”
position to turn off the blender, detach the plastic blender and pour out
blended foods.
The blender will also operate when the switch is turn to “Pulse” position.
When the switch is loosened, it will return to “0” position and automatic cut off
the power. This function is designed for short-time blending (a few seconds),
which makes it easy to control the blending results.
Do not operate the appliance for more than 3 minutes continuously at a time.
If you have not finished processing after 3 minutes, switch off the appliance
and let it cool down before you operate it again.
TIPS FOR GRINDER
Food (bean, rice, peanut, broad bean and coffee bean etc.) that are to be
milled must be sun dried with foreign materials removed.
Put food into the grinder and lock it onto the motor base. Do not add in water
when grinding.
Plug the power cord to a power source and adjust the switch to speed “1” or
speed “2” position. Thus food can be ground into powder in minutes. Adjust
the switch back on “0” position to turn off the unit, then remove the grinder and
pour out the food that have been ground.
The grinder will also operate when the switch is held on “Pulse” position.
When the switch is loosened, it will return “0” position and automatic cut off
the power. This function is designed for short-time grinding (a few seconds),
which makes it easy to control the grinding results.

5
CLEANING AND MAINTENANCE
1. Unplug the appliance.
2. Dissemble all removable parts before cleaning.
Note: Do not rinse the motor base under water tap. Do not use abrasive
cleaning agents, sources, etc. to clean the motor base!
3. When cleaning the plastic jar, be careful of the blades as it is very sharp.
4. Clean the motor base with a moist cloth.
5. Clean the removable parts immediately after use.
SPECIFICATIONS
1.Voltage : 220-240V, 50/60Hz
2.Power : 300-327W
3.Short time operation: max 3 minutes and need stop 3 minutes, run 5 times and rest
for 1 hour.
ENVIRONMENT-FRIENDLY DISPOSAL
You can help to protect the environment!
Please remember to respect the local regulations: hand in the
non-working electrical equipments to an appropriate waste disposal
centre.

6