Elba EHS 311D1 S Installation and operating instructions
Instructions for the use - Installation advices
100%
ELBA QUALITY
MADE IN ITALY
Made in Italy
DOMINO COOKING HOBS
EHS 311D1 S
EHS 321D1 S
2
Dear Customer,
Thank you for having purchased and given your preference to
our product.
The safety precautions and recommendations reported below
are for your own safety and that of others. They will also provide
a means by which to make full use of the features offered by your
appliance.
Please preserve this booklet carefully. It may be useful in future,
either to yourself or to others in the event that doubts should
arise relating to its operation.
This appliance must be used only for the task it has
explicitly been designed for, that is for cooking foodstuffs.
Any other form of usage is to be considered as inappropriate
and therefore dangerous.
The manufacturer declines all responsibility in the event
of damage caused by improper, incorrect or illogical use of
the appliance.
3
IMPORTANT SAFETY PRECAUTIONSAND RECOMMENDATIONS
IMPORTANT: This appliance is designed and manufactured
solely for the cooking of domestic (household) food and is
not suitable for any non domestic application and therefore
should not be used in a commercial environment.
The appliance guarantee will be void if the appliance is used
within a non domestic environment i.e. a semi commercial,
commercial or communal environment.
Read the instructions carefully before installing and using
the appliance.
• This appliance has been designed and manufactured in
compliance with the applicable standards for the household
cooking products, including those for surface temperatures.
Some people with sensitive skin may have a more pronounced
temperature perception with some components although these
parts are within the limits allowed by the norms.
Thecompletesafetyoftheappliancealsodependsonthecorrect
use, we therefore recommend to always pay a extreme attention
while using the product, especially in the presence of children.
• After having unpacked the appliance, check to ensure that it is
not damaged.
In case of doubt, do not use it and consult your supplier or a
• Packing elements (i.e. plastic bags, polystyrene foam, nails,
packing straps, etc.) should not be left around within easy reach
of children, as these may cause serious injuries.
•
aluminium parts. Thislmmustberemovedbeforeusingthe
appliance.
• IMPORTANT: The use of suitable protective clothing/gloves is
recommended when handling or cleaning this appliance.
• Do not attempt to modify the technical characteristics of
the appliance as this may become dangerous to use. The
manufacturer declines all responsibility for any inconvenience
resulting from the inobservance of this condition.
4
• CAUTION: this appIiance must only be installed in a permanently
ventilated room in compliance with the applicable regulations.
• Do not carry out cleaning or maintenance operations on the
appliance without having previously disconnected it from the
electric power supply.
• Do not use a steam cleaner because the moisture can get into
the appliance therefore making it unsafe.
• Do not cover the hob with aluminium foils.
• Do not touch the appliance with wet or damp hands (or feet).
• Do not use the appliance whilst in bare feet.
• If you should decide not to use this appliance any longer (or
decide to substitute another model), before disposing of it, it
is recommended that it be made inoperative in an appropriate
manner in accordance to health and environmental protection
regulations, ensuring in particular that all potentially hazardous
parts be made harmless, especially in relation to children who
could play with unused appliances.
• Thevariouscomponentsoftheappliancearerecyclable.Dispose
oftheminaccordancewiththeregulationsinforceinyourcountry.
If the appliance is to be scrapped, remove the power cord.
• After use, ensure that the knobs are in the off position.
• Children less than 8 years of age shall be kept away unless
continuously supervised.
• This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.
• The manufacturer declines all liability for injury to persons or
damage to property caused by incorrect or improper use of the
appliance.
• WARNING: During use the appliance and its accessible parts
become hot; they remain hot for some time after use.
5
– Care should be taken to avoid touching heating elements on
the hob.
– To avoid burns and scalds, young children should be kept
away.
• Make sure that electrical cables connecting other appliances in
the proximity of the cooktop cannot come into contact with the
hob.
• WARNING: Unattended cooking on a hob with fat or oil can be
•
surfaces.
• WARNING: When correctly installed, your product meets all
safety requirements laid down for this type of product category.
However special care should be taken around the underneath
of the appliance as this area is not designed or intended to be
touched and may contain sharp or rough edges, that may cause
injury.
• CAUTION: The cooking process has to be supervised. A short
term cooking process has to be supervised continuously.
• If the power supply cable is damaged, it must be replaced only
by an authorized service agent in order to avoid a hazard.
• For use with Town Gas:
– Do not attempt to modify or replace the external gas regulator
as it may cause safety issue.
– It is recommended to replace the external gas regulator every
2 years. Replacement of external gas regulator and service
cost will be borne by customer.
6
ADVICE
for the
INSTALLER
7
IMPORTANT :
The appliance is designed and approved for domestic use only and should not be
installed in a commercial, semi commercial or communal environment.
Your product will not be guaranteed if installed in any of the above environments
and could affect any third party or public liability insurances you may have.
This appliance is to be installed, regulated and adapted to function only by an authorized
person in compliance with the current local regulations in force and in observation of the
instructions supplied by the manufacturer.
Failure to comply with this condition will render the guarantee invalid.
The appliance must be installed in compliance with regulations in force in your country
and in observation of the manufacturer’s instructions.
Installation technicians must comply to current laws in force concerning ventilation and
the evacuation of exhaust gases.
Incorrect installation, for which the manufacturer accepts no responsibility, may cause
personal injury or damage.
This appliance shall only be serviced by authorized personnel.
Always disconnect the appliance from mains power supply before carrying out any
maintenance operations or repairs.
Important: The use of suitable protective clothing/gloves is recommended when
handling or cleaning of this appliance.
Thesetopsaredesignedtobeembeddedintokitchenxturesmeasuring600
mmindepth,workingsurface20to40mmthick.
The appliance must be housed in heat-resistant units.
The walls of the units must not be higher than work top and must be capable of
resistingtemperaturesof105°Caboveroomtemperature.
We would point out that the adhesive which bonds the plastic laminate to the
furnituremustwithstandtemperaturesnotlessthan150°Ctoavoiddelamination.
Donotinstalltheappliancenearinammablematerials(eg.curtains).
WARNING!
When correctly installed, your product meets all safety requirements laid down for
this type of product category. However special care should be taken around the
underneath of the appliance as this area is not designed or intended to be touched
and may contain sharp or rough edges, that may cause injury.
8
TECHNICAL INFORMATION FOR
THE INSTALLER
In order to install the cooker top into the
in mind the following:
A 30 mm ventilation gap must be
provided between the bottom of the
appliance and any cabinetry, draw
unit or appliance.
If the cooktop is installed above
an oven, the two appliances shall
be connected to the gas and/or
electrical supply with independent
connections.
The cooker top must be kept no less
The hob must be installed at least 50
There must be a distance of at least 650 mm between the hob and any wall cupboard or
650 mm
450 mm
min 100 mm
Fig. 1.2
INSTALLATION
1
490
510
270
– 2
288
50
30
Fig. 1.1
9
FASTENING THE INSTALLATION BRACKETS
the cooktop to benches from 20 to 40mm thick.
The kit includes two “F” type brackets (for the front of the cooktop), two “R” type brackets
(for the rear of the cooktop) and four self-threading screws “S”.
The kit includes 4 tabs “A” and 4 selfthreading screws “B”.
Cut the unit.
Stretch gasket “G” over the edge of the hole made, being careful to overlay the junction
Turn the cooktop over and put tabs “A
screws “B” a few turns. Make sure that the tabs are mounted correctly as shown in the
Put the cooktop into the hole cut into the unit and position it correctly.
Put tabs “A” into place, tooth “C” of the tabs should go into the hole.
Tighten screws “B” until the cooktop is completely secured.
Using a sharp tool cut off the part of gasket “G” which protrudes from the cooktop.
Take care not to damage the benchtop.
Fig. 1.3c
Fig. 1.3a
G
Fig. 1.3b
A
A
AA
20 mm min.
40 mm max.
B
D
A
C
AA
AA
VENTILATION REQUIREMENTS
The appliance must be installed in compliance with applicable local regulations
concerningventilationandtheevacuationofexhaustgases.
Intensiveandprolongedusemayrequireextraventilation,e.g.openingawindow,
ormoreefcientventilationincreasingthemechanicalsuctionpowerifthisistted.
CHOOSING SUITABLE SURROUNDINGS
the gas can burn (in compliance with applicable local regulations).
2(or refer to applicable local regulations).
combustion products and must be made so that they cannot be blocked from either the
inside or the outside.
When these openings cannot be made, the necessary air can come from an adjacent
room which is ventilated as required, as long as it is not a bed room or a danger area (in
compliance with applicable local regulations).
In this case, the kitchen door must allow the passage of the air.
DISCHARGING PRODUCTS OF COMBUSTION
If this is not possible, an electric fan may be used, attached to the external wall or the
window; the fan should have a capacity to circulate air at an hourly rate of 3-5 times the
Thefancan only be installed if the room has suitable vents to allow air to enter,asdescribed
under the heading “Choosing suitable surroundings”.
H min 650 mm
for products of
combustion
Air vent Air vent
extract products of
combustion
Fig. 1.5Fig. 1.4
GAS SECTION
2
GAS INSTALLATION REQUIREMENTS
Important !
• Before installation, make sure that the local distribution conditions (gas type and
pressure) and the adjustment of this appliance are compatible. The appliance
adjustment conditions are given on the plate or the label.
• This appliance must be installed and serviced only by a suitably qualied,
registered installer with technical knowledge of both gas installation and
electricity. The installation or service must comply with the current editions of
the applicable standards, regulations, and codes of practice governing gas and
electrical installations.
• Failure to install the appliance correctly could invalidate any manufacturer’s
warranty.
This appliance is supplied for use on Natural gas, LPG or Town Gas (check the gas
regulation label attached on the appliance).
Appliances supplied for use on Natural gas: they are adjusted for this gas only and
The appliances are manufactured for conversion to LPG and Town gas.
Appliances supplied for use on LPG: they are adjusted for this gas only and cannot be
The appliances are manufactured for conversion to Natural and Town gas.
Appliances supplied for use on Town gas: they are adjusted for this gas only and
The appliances are manufactured for conversion to Natural gas and LPG.
If the Natural gas/LPG/Town gas conversion kit is not supplied with the appliance this kit
can be purchased by contacting the After-Sales Service.
CONNECTING THE COOKTOP TO THE GAS SUPPLY
The gas connection must be carried out by an authorised person according to
the relevant local standards.
Ensure that the room in which the cooktop is to be installed is adequately
ventilated, in compliance with applicable regulations.
Note: Connection to the gas supply may be made using either a rubber hose
(wherepermitted)orbyusingaexiblehoseorrigidpipe.
The rear of the chassis is recessed to provide a channel for the appliance inlet pipe.
Thegasconnectiontting(brasselbow)canbeturnedinthedirectionrequired
(but never in a vertical or horizontal position) after loosening the elbow and
oating nut connection. Never attempt to turn the elbow without having rst
loosenedtheoatingnut.
The supplied sealing washers guarantee a good seal for the gas connection. We
recommend that you replace the sealing washers on the slightest sign of wear,
deformation or imperfection.
After connecting to the gas mains, check that the couplings are correctly sealed,
usingsoapysolution,butneveranakedame.
GAS CONNECTION WITH A RUBBER HOSE (NATURAL GAS OR LPG ONLY)
Important !
A rubber hose connection shall only be made if permitted by the applicable local
regulations.
the appliance inlet pipe;
the brass elbow;
the sealing washers;
the appropriate hose holder (for LPG or NATURAL GAS).
Important!
■ Donottthebrassconicalconnector,suppliedwiththeproductinaseparate
kit, to the brass elbow.
Floating nut
Brass elbow
Hose holder for
NATURAL GAS
or TOWN GAS
Hose clamp
(not supplied)
Rubber hose (not
supplied) for NATURAL
GAS connection (internal
Rubber hose (not supplied)
for LPG connection
(internal diameter 8 mm)
Hose clamp
(not supplied)
Hose holder for
NATURAL GAS
or TOWN GAS
Hose adaptor
for LPG
Appliance
inlet pipe
Gas connection with rubber hose holder (Natural gas or LPG only)
Note:ifnotalreadyttedontheinletpipe,thehoseholderissupplied
with the product in a separate kit; if not supplied with the appliance
it can be purchased by contacting Customer Care.
(Important: to be used ONLY IF PERMITTED by the local applicable regulations)
Fig. 2.1
Turning the gas
DO NOT USE the
brass conical
connector
(supplied with
the product in a
separate kit)
1/2” BSP
taper (conical)
(BS EN 10226-1)
male
Sealing washer
Sealing washer
Sealing washer
Connecting the appliance to LPG
NATURAL GAS hose holder on the inlet pipe, making sure
adaptor to the NATURAL GAS hose holder, making sure that you place the sealing
Important! The LPG hose holder is composed by NATURAL GAS hose holder
with LPG hose adaptor screwed at the bottom end (interposing the proper
sealing washer between them).
2. Connecttheappliancetothegas supply usingasuitable rubber hose(internaldiameter
8 mm).
The hose must comply with the applicable local regulations and be of the correct
construction for the type of gas being used.
3.
4. Use a standard hose clamp (not supplied) to fasten the hose.
5. Install a gas pressure regulator.
Important!
To comply with applicable local regulations, a gas pressure regulator (conforming
to the local regulations in force) must be installed when connecting the appliance to
an LPG cylinder.
Connecting the appliance to NATURAL GAS
NATURAL GAS hose holder on the inlet pipe, making sure
2. Connectthe appliance tothegas supply usingasuitable rubber hose(internaldiameter
The hose must comply with the applicable local regulations and be of the correct
construction for the type of gas being used.
3.
4. Use a standard hose clamp (not supplied) to fasten the hose.
When connecting the appliance to the gas supply with a rubber hose, make sure that
• the hose is as short as possible, without twists or kinks.
• the hose is not longer than 750 mm (or refer to applicable local regulations) and does
not come into contact with sharp edges, corners or moving parts, as these may cause
abrasion. Use a single rubber hose only; never connect the appliance with more than
one rubber hose.
• the hose is not under tension, twisted, kinked, or too tightly bent, neither while the
appliance is in use nor while it is being connected or disconnected.
• the hose does not come into contact with any part of the appliance with a surface
temperature of 70°C or above (or refer to applicable local regulations).
•
contact with hot surfaces.
• the hose can easily be inspected along its entire length to check its condition.
• the hose is replaced at the printed due date or if it shows signs of wear or damage, and
replaced regardless of its condition after a maximum of three years.
• youinformthecustomer that the gas cylinder valve or the gas supply valveimmediately
by the appliance should be closed when the cooktop is not in use.
• you inform the customer that the hose should not be subjected to corrosion by acidic
cleaning agents.
Floating nut
Brass elbow
Turning the gas
DO NOT USE the
brass conical
connector
(supplied with
the product in a
separate kit)
Rigid pipe
(not supplied)
Flexible hose
(not supplied)
Appliance
inlet pipe
After connecting the appliance to the gas supply, make sure that you
• check that the connections are correctly sealed using a soapy solution, but never a
• check whether the injectors are correct for the type of gas being used. If not, follow the
• replace the sealing washer/s on the slightest sign of deformation or imperfection. The
sealing washer/s is/are the part/s which guarantee/s a good seal in the gas connection.
GAS CONNECTION WITH RIGID PIPES OR A FLEXIBLE HOSE (NATURAL
GAS OR LPG ONLY)
the appliance inlet pipe;
the brass elbow;
the sealing washers.
Important!
■ Iftted,removethehoseholderfromtheterminalttingoftheinletpipe.
■ Donottthebrassconicalconnector,suppliedwiththeproductinaseparate
kit, to the brass elbow.
Gasconnectionwithrigidpipesoraexiblehose(Natural Gas or LPG only)
Note:ifalreadyttedontheinletpipe,removetherubberhoseholder
Fig. 2.2
1/2” BSP
taper (conical)
(BS EN 10226-1)
male
Sealing washer
Sealing washer
Whenconnectingtheappliancetothegassupplywithrigidpipesoraexiblehose,
make sure that
the correct size to maintain the heat output of the appliance.
the connection with rigid metal pipes does not cause stress or pressure to the gas
piping.
the appliance is in use nor while it is being connected or disconnected.
regulations) and does not come into contact with sharp edges, corners or moving
if it has an expiry date, it should be replaced before that date.
come into contact with any part of the cooktop with a surface temperature of 70°C or
above (or refer to applicable local regulations).
by contact with hot surfaces.
a gas pressure regulator, in compliance with the applicable local regulations, is
installed when connecting to an LPG cylinder.
for service or removal.
you inform the customer that the cylinder valve or the supply valve immediately by the
appliance should be closed when the cooktop is not in use.
corrosion by acidic cleaning agents.
After connecting the appliance to the gas supply, make sure that you
check that the connections are correctly sealed using a soapy solution, but never a
check whether the injectors are correct for the type of gas being used. If not, follow the
replace the sealing washer/s on the slightest sign of deformation or imperfection. The
sealing washer/s is/are the part/s which guarantee/s a good seal in the gas connection.
GAS CONNECTION FOR TOWN GAS ONLY
The gas connection is made up of (Fig. 2.3):
the appliance inlet pipe;
the foating nut;
the brass elbow;
sealing washers;
the Town gas pressure regulator.
Important!
■ Iftted,removethehoseholderfromtheterminalttingoftheinletpipe.
■ Thebrassconicalconnectorisnotalreadyttedontheappliance(itissupplied
in a separate kit); screw that connector to the brass elbow, interposing the
sealing washer provided, before starting the connection to the gas supply.
Besuretottheconicalconnectorasindicatedingure2.3.
Pay special attention to not loosentheelbowandoatingnutconnectionwhen
ttingthebrassconnector.
When connecting the cooktop to the town gas supply, make sure that
agas pressureregulator,in compliancewith theapplicablelocalregulations,is installed
when connecting to Town gas. Do not over tighten the brass conical connector and
the chapter “”.
check its condition. It has to be replaced if it shows signs of wear or damage. If it has
an expiry date, it should be replaced before that date.
which it will be connected.
use or whilst being connected or disconnected.
contact with hot surfaces.
in accordance with the manufacturer installation manual.
i.e. abrasion from furniture drawers, doors, moving parts in kitchen work stations or
corners, sharp edges.
you inform the customer that the cylinder valve or the supply valve immediately by the
appliance should be closed when the cooktop is not in use.
acidic cleaning agents.
After connecting the appliance to the gas supply, make sure that you
check that the connections are correctly sealed using a soapy solution, but never a
check whether the injectors are correct for the type of gas being used. If not, follow the
between the brass elbow and the brass conical connector) on the slightest sign of
deformation or imperfection. The sealing washers are the parts which guarantee a
good seal in the gas connection.
Gas connection for Town gas only
Town gas
1/2” G cylindrical
(ISO 228-1) female
1/2” G cylindrical
(ISO 228-1) male
1/2” G cylindrical
(ISO 228-1) female
1/2” G cylindrical
(ISO 228-1) male
1/2” BSP taper (conical)
(BS EN 10226-1) male
1/2” BSP taper (conical)
(BS EN 10226-1) male
1/2” BSP
female
1/2” BSP
female
(#)Supplied with
the appliance in
a separate kit
Appliance inlet pipe
Floating nut
Brass elbow
Sealing washer (#) Sealing washer
Brass conical
connector (#)
Gas pressure regulator
for Town gas
• Inputpressure:50mbar
max.
• Output pressure: 8 mbar
See also chapter:
“ADJUSTMENT OF THE
EXTERNAL GAS REGULATOR
(TOWN GAS)”
Flexible hose for Town gas
(not supplied)
Fig. 2.3
ARROW
Do not over tighten the
brass conical connector
andtheexiblehose
to the regulator. Over
tightening may crack
regulator.
USE
the brass conical
connector
(supplied with
the product in a
separate kit)
1/2” BSP
taper (conical)
(BS EN 10226-1)
male
TABLE FOR THE CHOICE OF THE INJECTORS
Nominal
power
Reduced
power
LPG
G30
28 mbar
Natural Gas
G20
20 mbar
Town Gas
8 mbar
Ø injector
Ø injector
Ø injector
Semi-rapid (SR) 0,45 66
Rapid (R) 3,00 0,75 87 280
Triple-ring (TR) 3,80 98 350
3/h x kW)
Air necessary for combustion [m3
Semi-rapid (SR) 3,50
Rapid (R) 6,00
Triple-ring (TR) 7,60
LUBRICATION OF THE GAS TAPS
IMPORTANT
Allinterventionregardinginstallationmaintenanceoftheappliancemustbefullled
with original factory parts.
The manufacturer declines any liability resulting from the non-compliance of this
obligation.
GAS MAINTENANCE
TESTINGOPERATION(FORALLGASESANDALLTYPESOFCONNECTIONS)
The operation of the appliance MUST be tested before leaving.
yellow tipping. If any abnormailty is evident, check that the burner cap is located properly
and the injector nipple is aligned correctly.
Check the minimum burner setting by quickly rotating the burner knobs from the maximum
section “” following.
If satisfactory performance cannot be obtained, check the installation and notify the local
gas supply authority of a gas supply problem, or if it is an appliance problem, Customer
Care should be called to obtain the nearest authorised Service Agent.
J
REPLACEMENT OF THE INJECTORS
If the injectors are not supplied they can
be obtained from the “Service Centre”.
Selecttheinjectorstobereplacedaccording
The nozzle diameters, expressed in
hundredths of a millimeter, are marked on
the body of each injector.
REPLACEMENT OF THE
INJECTORS OF THE COOKTOP
BURNERS
To replace the injectors proceed as follows:
Remove pan supports and burners
from the cooktop.
Using a wrench, substitute the
injectors “J
those most suitable for the kind of gas
for which it is to be used.
gas regulation label (at the bottom of
the appliance) shall be replaced by the
new label supplied together with the
injectors gas conversion kit.
The burners are conceived in such a
way so as not to require the regulation
of the primary air.
SETTING THE MINIMUM OF THE
COOKTOP BURNERS
have a length of about 4 mm and must
remain lit even with a quick turn from the
maximum position to that of minimum.
following way:
Turn on the burner.
Turn the tap to the 'MINIMUM' position.
Take off the knob.
screw “A
2.5).
NormallyforLPG(G3050mbar), tighten
up the regulation screw. Fig. 2.5
J
Fig. 2.4a
Semi-rapid
and rapid
burners
Triple-ring
burner
Fig. 2.4b
A
20
ADJUSTMENT OF THE EXTERNAL
GAS REGULATOR (TOWN GAS)
For Town Gas (TG) installation, external
gas pressure regulator must be installed.
The TG regulator (provided with the
Fig. 2.6.
To regulate the external gas pressure
regulator, it is necessary to follow the
following steps:
Connect the gas regulator to the
appliance (arrow up) and the other end
2. Remove the screw from the test point.
Make sure that the rubber gasket is
intact with the screw when removing.
3. Adjust the pressure by using the gas
test gauge (U-gauge).
Connect the U-gauge to the test point
with tube hose (refer to Fig. 2.7).
Turn on the gas burner (the biggest
burner) to the maximum power and
adjust the pressure to 8 mbar by using
the adjustable screw.
4. After setting is completed, lock the
pressure (8 mbar) by tightening the
locking nut and re-mount the test point
screw (make sure that the rubber
gasket is intact with the screw).
5. Perform gas leak test after installation
is completed (using a soapy solution,
Details of the regulator:
MDGELITREGVN-01
• Modelnumber:EL-12550(EL-125)
• Gas inlet/outlet connection: ½ inch
BSP internal thread
• Maximuminletpressure:50mbar
• Regulated nominal outlet pressure:
8 mbar
Fig. 2.6
Fig. 2.7
Test point
Make sure
that the rubber
gasket is intact
with the screw
Adjustable
screw
Locking
nut
This manual suits for next models
2
Table of contents
Other Elba Hob manuals
Elba
Elba E30-800 X Technical manual
Elba
Elba EIF 57 PRO User manual
Elba
Elba ELIO 75-300 User manual
Elba
Elba DOMINO HOBS User manual
Elba
Elba ECH-A2229 User manual
Elba
Elba 345-004 Technical manual
Elba
Elba EGH-G6404G User manual
Elba
Elba 6E EX 397 I Installation and operating instructions
Elba
Elba 77-005 SS User manual
Elba
Elba P6D User manual
Elba
Elba EF60-440 X.1 User manual
Elba
Elba EH321 User manual
Elba
Elba E74-200 Installation and operating instructions
Elba
Elba Elio 345-003 Technical manual
Elba
Elba EH 733 WH User manual
Elba
Elba EGH-K8942G User manual
Elba
Elba P70 User manual
Elba
Elba EVNF 460 User manual
Elba
Elba EAVF 46 PRO User manual
Elba
Elba P60 Quick guide
Popular Hob manuals by other brands
Belling
Belling GHU60GE W Users guide & installation handbook
Hotpoint Ariston
Hotpoint Ariston THC 642 IX/HA TK operating instructions
AEG
AEG HD634170NB user manual
Electrolux
Electrolux EHL6645X Installation and operating instructions
AEG
AEG U05011 mixed km 6.24 user manual
Ariston
Ariston KT 8104 QO User instruction book