Elba EHS 935D1 SB Technical manual

Made in Italy
100%
ELBA QUALITY
MADE IN ITALY
BUILT-IN COOKING HOBS
EHS 935D1 SB
EHS 945D1 SB
EHS 948D1 S
Instructions for the use - Installation advices

2
Dear Customer,
Thank you for having purchased and given your preference to
our product.
The safety precautions and recommendations reported below
are for your own safety and that of others. They will also provide
a means by which to make full use of the features offered by your
appliance.
Please preserve this booklet carefully. It may be useful in future,
either to yourself or to others in the event that doubts should
arise relating to its operation.
This appliance must be used only for the task it has
explicitly been designed for, that is for cooking foodstuffs.
Any other form of usage is to be considered as inappropriate
and therefore dangerous.
The manufacturer declines all responsibility in the event
of damage caused by improper, incorrect or illogical use of
the appliance.

3
IMPORTANT SAFETY PRECAUTIONSAND RECOMMENDATIONS
IMPORTANT: This appliance is designed and manufactured
solely for the cooking of domestic (household) food and is
not suitable for any non domestic application and therefore
should not be used in a commercial environment.
The appliance guarantee will be void if the appliance is used
within a non domestic environment i.e. a semi commercial,
commercial or communal environment.
Read the instructions carefully before installing and using
the appliance.
• This appliance has been designed and manufactured in
compliance with the applicable standards for the household
cooking products, including those for surface temperatures.
Some people with sensitive skin may have a more pronounced
temperature perception with some components although these
parts are within the limits allowed by the norms.
Thecompletesafetyoftheappliancealsodependsonthecorrect
use, we therefore recommend to always pay a extreme attention
while using the product, especially in the presence of children.
• After having unpacked the appliance, check to ensure that it is
not damaged.
In case of doubt, do not use it and consult your supplier or a
professionally qualied technician.
• Packing elements (i.e. plastic bags, polystyrene foam, nails,
packing straps, etc.) should not be left around within easy reach
of children, as these may cause serious injuries.
• Some appliances are supplied with a protective lm on steel and
aluminium parts. Thislmmustberemovedbeforeusingthe
appliance.
• IMPORTANT: The use of suitable protective clothing/gloves is
recommended when handling or cleaning this appliance.
• Do not attempt to modify the technical characteristics of
the appliance as this may become dangerous to use. The
manufacturer declines all responsibility for any inconvenience
resulting from the inobservance of this condition.

4
• CAUTION: this appIiance must only be installed in a permanently
ventilated room in compliance with the applicable regulations.
• Do not operate your appliance by means of an external timer or
separate remote-control system.
• Do not carry out cleaning or maintenance operations on the
appliance without having previously disconnected it from the
electric power supply.
• Do not use a steam cleaner because the moisture can get into
the appliance therefore making it unsafe.
• Do not cover the hob with aluminium foils.
• Do not touch the appliance with wet or damp hands (or feet).
• Do not use the appliance whilst in bare feet.
• If you should decide not to use this appliance any longer (or
decide to substitute another model), before disposing of it, it
is recommended that it be made inoperative in an appropriate
manner in accordance to health and environmental protection
regulations, ensuring in particular that all potentially hazardous
parts be made harmless, especially in relation to children who
could play with unused appliances.
• Thevariouscomponentsoftheappliancearerecyclable.Dispose
oftheminaccordancewiththeregulationsinforceinyourcountry.
If the appliance is to be scrapped, remove the power cord.
• After use, ensure that the knobs are in the off position.
• Children less than 8 years of age shall be kept away unless
continuously supervised.
• This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.
• The manufacturer declines all liability for injury to persons or
damage to property caused by incorrect or improper use of the
appliance.

5
• WARNING: During use the appliance and its accessible parts
become hot; they remain hot for some time after use.
– Care should be taken to avoid touching heating elements on
the hob.
– To avoid burns and scalds, young children should be kept
away.
• Make sure that electrical cables connecting other appliances in
the proximity of the cooktop cannot come into contact with the
hob.
• WARNING: Unattended cooking on a hob with fat or oil can be
dangerous and may result in re. NEVER try to extinguish a re
with water, but switch off the appliance and then cover ame e.g.
with a lid or a re blanket.
• WARNING: Danger of re: do not store items on the cooking
surfaces.
• WARNING: If the hob is cracked or otherwise damaged by falling
objects etc., disconnect the appliance from the electrical power
supply to avoid the possibility of electric shock and call Customer
Service.
• WARNING: When correctly installed, your product meets all
safety requirements laid down for this type of product category.
However special care should be taken around the underneath
of the appliance as this area is not designed or intended to be
touched and may contain sharp or rough edges, that may cause
injury.
• CAUTION: The cooking process has to be supervised. A short
term cooking process has to be supervised continuously.
• If the power supply cable is damaged, it must be replaced only
by an authorized service agent in order to avoid a hazard.

6
Advice for
the installer

7
IMPORTANT :
• The appliance is designed and approved for domestic use only and should not be
installed in a commercial, semi commercial or communal environment.
Your product will not be guaranteed if installed in any of the above environments
and could affect any third party or public liability insurances you may have.
• This appliance is to be installed, regulated and adapted to function only by an authorized
person in compliance with the current local regulations in force and in observation of the
instructions supplied by the manufacturer.
Failure to comply with this condition will render the guarantee invalid.
• The appliance must be installed in compliance with regulations in force in your country
and in observation of the manufacturer’s instructions.
• Installation technicians must comply to current laws in force concerning ventilation and
the evacuation of exhaust gases.
• Incorrect installation, for which the manufacturer accepts no responsibility, may cause
personal injury or damage.
• This appliance shall only be serviced by authorized personnel.
• Always disconnect the appliance from mains power supply before carrying out any
maintenance operations or repairs.
• Important: The use of suitable protective clothing/gloves is recommended when
handling or cleaning of this appliance.
• Thesetopsaredesignedtobeembeddedintokitchenxturesmeasuring600
mm in depth.
• The appliance must be housed in heat-resistant units.
• The walls of the units must not be higher than work top and must be capable of
resistingtemperaturesof105°Caboveroomtemperature.
• We would point out that the adhesive which bonds the plastic laminate to the
furnituremustwithstandtemperaturesnotlessthan150°Ctoavoiddelamination.
• Donotinstalltheappliancenearinammablematerials(eg.curtains).
WARNING!
When correctly installed, your product meets all safety requirements laid down for
this type of product category. However special care should be taken around the
underneath of the appliance as this area is not designed or intended to be touched
and may contain sharp or rough edges, that may cause injury.

8
TECHNICAL INFORMATION FOR THE
INSTALLER
In order to install the cooker top into the kitchen
xture, a hole with the dimensions shown in
g. 1.2 has to be made, bearing in mind the
following:
• within the unit, between the bottom of the
cooktop and the upper surface of a shelf
there must be a clearance of at least 30
mm. It is absolutely essential that you
place a separator between the base of the
cooktop and the built-in unit or the oven;
• the cooker top must be kept no less than
200 mm away from any side wall (g. 1.2);
• the hob must be installed at least 60 mm
from the wall;
• there must be a distance of at least
650 mm between the hob and any wall
cupboard or extractor hood positioned
immediately above (see g. 1.1);
• if the hob is
installed over
a built-in oven,
there must be
a distance of
at least 30 mm
between the
two appliances.
The two
appliances shall
be connected
to the gas /
electrical supply
with independent
connections.
650 mm
60 mm min
200 mm min
500 mm
450 mm
860
480
500
60 min
840
200 min
Fig. 1.2
Fig. 1.1
30 mm
Space for
connections
Clearance
Door
INSTALLATION IN KITCHEN
CABINET WITH DOOR (g. 1.3)
It is recommended that a 30mm clearance
be left between to base of the cooktop and
the separator.
The separator shall be heat resistant, made
of low thermal conductivity material and
shall be removable with the use of a tool for
installation and service.
Fig. 1.3
INSTALLATION
1

9
FASTENING THE INSTALLATION BRACKETS (g. 1.4)
• Each cooker top is provided with an installation kit including brackets and screws for
fastening the top to xture panels from 2 to 4 cm thick.
• Turn the cooker top upside down and fasten the brackets “A” to the appropriate socket
holes, without tightening the screws “B” for the moment.
• Make sure that the brackets are fastened as shown in gure 1.4.
FASTENING THE COOKER TOP (g. 1.5)
• Spread the sealing material “C” out along the xture hole, making sure that the
junctions overlap at the corners.
• Insert the cooker top into the hole and position it correctly.
• Adjust the position of the brackets “A” and tighten screws “B” to block the cooker top
rmly in position.
• With a sharp cutter or trimmer knife trim the excess sealing material around the edge
of the cooker top. Take care not to damage the benchtop.
20 mm min.
40 mm max.
B
C
A
A
A
A
A
A
A
Fig. 1.4
Fig. 1.5

10
VENTILATION REQUIREMENTS
The appliance must be installed in compliance with applicable local regulations
concerningventilationandtheevacuationofexhaustgases.
Intensiveandprolongedusemayrequireextraventilation,e.g.openingawindow,
ormoreefcientventilationincreasingthemechanicalsuctionpowerifthisistted.
CHOOSING SUITABLE SURROUNDINGS
The room where the gas appliance is to be installed must have a natural ow of air so that
the gas can burn (in compliance with applicable local regulations).
The ow of air must come directly from one or more openings made in the outside walls
with a free area of at least 100 cm2(or refer to applicable local regulations).
The openings should be near the oor and preferably on the side opposite the exhaust for
combustion products and must be made so that they cannot be blocked from either the
inside or the outside.
When these openings cannot be made, the necessary air can come from an adjacent
room which is ventilated as required, as long as it is not a bed room or a danger area (in
compliance with applicable local regulations).
In this case, the kitchen door must allow the passage of the air.
DISCHARGING PRODUCTS OF COMBUSTION
Extractor hoods connected directly to the outside must be provided, to allow the products
of combustion of the gas appliance to be discharged (g. 1.6).
If this is not possible, an electric fan may be used, attached to the external wall or the
window; the fan should have a capacity to circulate air at an hourly rate of 3-5 times the
total volume of the kitchen (g. 1.7).
Thefancan only be installed if the room has suitable vents to allow air to enter,asdescribed
under the heading “Choosing suitable surroundings”.
H min 650 mm
Extractor hood
for products of
combustion
Air vent Air vent
Electric fan to
extract products of
combustion
Fig. 1.7Fig. 1.6

11
GAS SECTION
2
GAS INSTALLATION REQUIREMENTS
Important !
• Before installation, make sure that the local distribution conditions (gas type and
pressure) and the adjustment of this appliance are compatible. The appliance
adjustment conditions are given on the plate or the label.
• This appliance must be installed and serviced only by a suitably qualied,
registered installer with technical knowledge of both gas installation and
electricity. The installation or service must comply with the current editions of
the applicable standards, regulations, and codes of practice governing gas and
electrical installations.
• Failure to install the appliance correctly could invalidate any manufacturer’s
warranty.
This appliance is supplied for use on Natural gas, LPG or Town Gas (check the gas
regulation label attached on the appliance).
• Appliances supplied for use on Natural gas: they are adjusted for this gas only and
cannot be used on any other gas (LPG or Town gas) without modication.
The appliances are manufactured for conversion to LPG and Town gas.
• Appliances supplied for use on LPG: they are adjusted for this gas only and cannot be
used on any other gas (Natural or Town gas) without modication.
The appliances are manufactured for conversion to Natural and Town gas.
• Appliances supplied for use on Town gas: they are adjusted for this gas only and
cannot be used on any other gas (Natural gas or LPG) without modication.
The appliances are manufactured for conversion to Natural gas and LPG.
If the Natural gas/LPG/Town gas conversion kit is not supplied with the appliance this kit
can be purchased by contacting the After-Sales Service.
CONNECTING THE COOKTOP TO THE GAS SUPPLY
• The gas connection must be carried out by an authorised person according to
the relevant local standards.
• Ensure that the room in which the cooktop is to be installed is adequately
ventilated, in compliance with applicable regulations.
• Note: Connection to the gas supply may be made using either a rubber hose
(wherepermitted)orbyusingaexiblehoseorrigidpipe.
• The rear of the chassis is recessed to provide a channel for the appliance inlet pipe.
• Thegasconnectiontting(brasselbow)canbeturnedinthedirectionrequired
(but never in a vertical or horizontal position) after loosening the elbow and
oating nut connection. Never attempt to turn the elbow without having rst
loosenedtheoatingnut.
• The supplied sealing washers guarantee a good seal for the gas connection. We
recommend that you replace the sealing washers on the slightest sign of wear,
deformation or imperfection.
• After connecting to the gas mains, check that the couplings are correctly sealed,
usingsoapysolution,butneveranakedame.

12
GAS CONNECTION WITH A RUBBER HOSE
Important !
A rubber hose connection shall only be made if permitted by the applicable local
regulations.
The gas connection tting (g. 2.1) is made up of:
• the appliance inlet pipe;
• the oating nut;
• the brass elbow;
• the sealing washers;
• the appropriate hose holder (for LPG, TOWN GAS or NATURAL GAS).
Floating nut
Brass elbow
1/2” G cylindrical
(ISO 228-1) male
1/2” G cylindrical
(ISO 228-1) male
1/2” G cylindrical
(ISO 228-1) female
1/2” G cylindrical
(ISO 228-1) female
Hose holder for
NATURAL GAS
or TOWN GAS
Hose clamp
(not supplied)
Rubber hose (not supplied)
for LPG connection
(internal diameter 8 mm)
Hose clamp
(not supplied)
Hose holder for
NATURAL GAS
or TOWN GAS
Hose adaptor
for LPG
Appliance
inlet pipe
Gas connection with rubber hose holder
Note:ifnotalreadyttedontheinletpipe,thehoseholderissupplied
with the product in a separate kit; if not supplied with the appliance
it can be purchased by contacting Customer Care.
(Important: to be used ONLY IF PERMITTED by the local applicable regulations)
Fig. 2.1
Turning the gas
connection tting
Sealing washer
Sealing washer
Sealing washer
Rubber hose (not
supplied) for TOWN
GAS or NATURAL GAS
connection
(internal diameter
13 mm)

13
Connecting the appliance to LPG
1. If not already tted, t the TOWN GAS/NATURAL GAS hose holder on the inlet pipe,
making sure that you place the sealing washer between them (as shown in g. 2.1);
then t the LPG adaptor to the TOWN GAS/NATURAL GAS hose holder, making sure
that you place the sealing washer between them (as shown in g. 2.1).
Important! The LPG hose holder is composed by TOWN GAS/NATURAL GAS
hose holder with LPG hose adaptor screwed at the bottom end (interposing the
proper sealing washer between them).
2. Connectthe appliance tothegas supply usingasuitable rubber hose(internal diameter
8 mm).
The hose must comply with the applicable local regulations and be of the correct
construction for the type of gas being used.
3. Make sure that the hose is tightly and securely tted at both ends.
4. Use a standard hose clamp (not supplied) to fasten the hose.
5. Install a gas pressure regulator.
Important!
To comply with applicable local regulations, a gas pressure regulator (conforming
to the local regulations in force) must be installed when connecting the appliance to
an LPG cylinder.
Connecting the appliance to TOWN GAS or NATURAL GAS
1. If not already tted, t the TOWN GAS/NATURAL GAS hose holder on the inlet pipe,
making sure that you place the sealing washer between them (as shown in g. 2.1).
2. Connectthe appliance tothegas supply usingasuitable rubber hose(internal diameter
13 mm).
The hose must comply with the applicable local regulations and be of the correct
construction for the type of gas being used.
3. Make sure that the hose is tightly and securely tted at both ends.
4. Use a standard hose clamp (not supplied) to fasten the hose.
When connecting the appliance to the gas supply with a rubber hose, make sure that
• the hose is as short as possible, without twists or kinks.
• the hose is not longer than 750 mm (or refer to applicable local regulations) and does
not come into contact with sharp edges, corners or moving parts, as these may cause
abrasion. Use a single rubber hose only; never connect the appliance with more than
one rubber hose.
• the hose is not under tension, twisted, kinked, or too tightly bent, neither while the
appliance is in use nor while it is being connected or disconnected.
• the hose does not come into contact with any part of the appliance with a surface
temperature of 70°C or above (or refer to applicable local regulations).
• the hose is not subject to excessive heat by direct exposure to ue products or by
contact with hot surfaces.
• the hose can easily be inspected along its entire length to check its condition.
• the hose is replaced at the printed due date or if it shows signs of wear or damage, and
replaced regardless of its condition after a maximum of three years.
• youinformthe customer that the gas cylinder valve or the gas supplyvalveimmediately
by the appliance should be closed when the cooktop is not in use.
• you inform the customer that the hose should not be subjected to corrosion by acidic
cleaning agents.

14
Floating nut
Brass elbow
1/2” G cylindrical
(ISO 228-1) male
1/2” G cylindrical
(ISO 228-1) male
1/2” G cylindrical
(ISO 228-1) female
Turning the gas
connection tting
1/2” G cylindrical
(ISO 228-1) female
Rigid pipe
(not supplied)
Flexible hose
(not supplied)
Appliance
inlet pipe
After connecting the appliance to the gas supply, make sure that you
• check that the connections are correctly sealed using a soapy solution, but never a
naked ame.
• check whether the injectors are correct for the type of gas being used. If not, follow the
instructions under “GAS MAINTENANCE”.
• replace the sealing washer/s on the slightest sign of deformation or imperfection. The
sealing washer/s is/are the part/s which guarantee/s a good seal in the gas connection.
GAS CONNECTION WITH RIGID PIPES OR A FLEXIBLE HOSE
The gas connection tting (g. 2.2) is made up of:
• the appliance inlet pipe;
• the oating nut;
• the brass elbow;
• the sealing washers.
Important!
■ Iftted,removethehoseholderfromtheterminalttingoftheinletpipe.
Gasconnectionwithrigidpipesoraexiblehose
Note:ifalreadyttedontheinletpipe,removetherubberhoseholder
Fig. 2.2
Sealing washer
Sealing washer

15
Whenconnectingtheappliancetothegassupplywithrigidpipesoraexiblehose,
make sure that
• you use rigid pipes or a exible hose complying with applicable local regulations. The
exible hose shall be of the correct construction for the type of gas being used and of
the correct size to maintain the heat output of the appliance.
• the connection with rigid metal pipes does not cause stress or pressure to the gas
piping.
• the exible hose is not under tension, twisted, kinked or too tightly bent, neither while
the appliance is in use nor while it is being connected or disconnected.
• the exible hose does not exceed 2000 mm in length (or refer to applicable local
regulations) and does not come into contact with sharp edges, corners or moving
parts, as these may cause abrasion. Use a single exible hose only; never connect the
appliance with more than one exible hose.
• the exible hose can easily be inspected along its entire length to check its condition;
if it has an expiry date, it should be replaced before that date.
• if using a exible hose which is not entirely made of metal, make sure that it does not
come into contact with any part of the cooktop with a surface temperature of 70°C or
above (or refer to applicable local regulations).
• the exible hose is not subject to excessive heat by direct exposure to ue products or
by contact with hot surfaces.
• the rigid pipe or exible hose is replaced if it shows signs of wear or damage.
• a gas pressure regulator, in compliance with the applicable local regulations, is
installed when connecting to an LPG cylinder.
• the socket into which the plug of the exible hose t is permanently attached to a rmly
xed gas installation pipe and is positioned so that the hose hangs freely downwards.
• the plug of the exible hose is accessible after installation, so that it can be disconnected
for service or removal.
• you inform the customer that the cylinder valve or the supply valve immediately by the
appliance should be closed when the cooktop is not in use.
• you inform the customer that the rigid pipe or exible hose should not be subjected to
corrosion by acidic cleaning agents.
After connecting the appliance to the gas supply, make sure that you
• check that the connections are correctly sealed using a soapy solution, but never a
naked ame.
• check whether the injectors are correct for the type of gas being used. If not, follow the
instructions under “GAS MAINTENANCE”.
• replace the sealing washer/s on the slightest sign of deformation or imperfection. The
sealing washer/s is/are the part/s which guarantee/s a good seal in the gas connection.
TESTING OPERATION
The operation of the appliance MUST be tested before leaving.
Turn on the gas and light each burner. Check for a well-dened blue ame without any
yellow tipping. If any abnormailty is evident, check that the burner cap is located properly
and the injector nipple is aligned correctly.
Check the minimum burner setting by quickly rotating the burner knobs from the maximum
to the minimum position: the ame must not go out. If the adjustment is required, see
section “SETTING THE MINIMUM OF THE COOKTOP BURNERS” following.
If satisfactory performance cannot be obtained, check the installation and notify the local
gas supply authority of a gas supply problem, or if it is an appliance problem, Customer
Care should be called to obtain the nearest authorised Service Agent.

16
TABLE FOR THE CHOICE OF THE INJECTORS
BURNERS Nominal
power
[kW]
Reduced
power
[kW]
LPG
G30
28 mbar
Natural Gas
G20
20 mbar
Town Gas
G110
8 mbar
Ø injector
[1/100 mm] Ø injector [1/100 mm] Ø injector [1/100 mm]
Auxiliary (A) 1,00 0,30 50 77 145
Semi-rapid (SR) 1,75 0,45 66 101 192
Triple-ring (TR) 3,50 1,50 93 135 310
AIR VENT NECESSARY FOR GAS COMBUSTION = (2 m3/h x kW)
BURNERS Air necessary for combustion [m3/h]
Auxiliary (A) 2,00
Semi-rapid (SR) 3,50
Triple-ring (TR) 7,00
LUBRICATION OF THE GAS TAPS
In case of difculty in the gas taps operation, call Service.
IMPORTANT
Allinterventionregardinginstallationmaintenanceoftheappliancemustbefullled
with original factory parts.
The manufacturer declines any liability resulting from the non-compliance of this
obligation.
GAS MAINTENANCE

17
J
Fig. 2.5
J
Fig. 2.4a
Auxiliary and
semi-rapid
burners
Triple-ring
burner
Fig. 2.4b
REPLACEMENT OF THE INJECTORS
Selecttheinjectorstobereplacedaccording
to the “TABLE FOR THE CHOICE OF THE
INJECTORS”.
The nozzle diameters, expressed in
hundredths of a millimetre, are marked on
the body of each injector.
If the injectors are not supplied they can
be obtained from the “Service Centre”.
REPLACEMENT OF THE
INJECTORS OF THE COOKTOP
BURNERS
To replace the injectors proceed as follows:
• Remove pan supports and burners
from the cooktop.
• Using a wrench, substitute the
injectors “J” (gs. 2.4a, 2.4b) with
those most suitable for the kind of gas
for which it is to be used.
The burners are conceived in such a
way so as not to require the regulation
of the primary air.
SETTING THE MINIMUM OF THE
COOKTOP BURNERS
In the minimum position the ame must
have a length of about 4 mm and must
remain lit even with a quick turn from the
maximum position to that of minimum.
The ame adjustment is done in the
following way:
• Turn on the burner.
• Turn the tap to the 'MINIMUM' position.
• Take off the knob.
• With a small at screwdriver turn the
screw “A” to the correct regulation (g.
2.5).
Normally for LPG tighten up the
regulation screw.
A

18
ELECTRICAL SECTION
3
GENERAL
• Connection to the electric power
supply must be carried out by a
qualied technician and following the
appropriate safety regulations.
• The appliance must be connected to
the mains checking that the voltage
corresponds to the value given in the
rating plate and that the electrical
cable sections can withstand the load
specied on the plate.
• If the hob is supplied without plug, t
a standard plug which is suitable for
the power absorbed by the appliance
and in conformity with the local rules
in force.
• The colours of the wires in the
appliance power cable may not
correspond with the colours marked
on the terminals of your electrical plug.
The plug should always be wired as
follows:
– connect the green/yellow wire to the
terminal marked with the letter 'E' or
the earth symbol ' ' or coloured
green/yellow;
– connect the blue wire to the terminal
markedwith theletter'N' orcoloured
black;
– connect the brown wire to the
terminal marked with the letter 'L' or
coloured red.
• The plug must be connected to an
outlet connected to the grounding unit
in conformity to security norms.
• If the appliance is to be connected
directly to the mains, it must be placed
with anomnipolarswitchwithminimum
opening between the contacts of 3 mm
between the appliance and the mains.
• Thepowersupplycable mustnot touch
the hot parts and must be positioned
so that it does not exceed 50°C above
ambient.
• Oncethe appliance has been installed,
the power switch or power plug must
always be in a accessible position.
• If the power supply cable is damaged it
must be substituted by a suitable cable
available in the after sales service.
N.B. For connection to the mains, do
not use adapters, reducers or branching
devices as they can cause overheating
and burning.
In the event that installation should
require modications to the mains supply
wiring system, it is recommended that a
qualied technician be called to carry out
substitution.
The technician will also have to verify that
the cross-section of the electric cables
on the power point match the appliance’s
power rating.
Before effecting any intervention
on the electrical parts the appliance
must be disconnected from the
network.
If the hob surface is cracked
disconnect the appliance from the
mains and contact the After-Sales
Service.
The connection of the appliance to
the grounding unit is mandatory.
The manufacturer declines every
responsability for any inconvenience
resulting from the inobservance of
this condition.

19
POWER SUPPLY CABLE
TYPE “H05V2V2-F”
(resistancetotemperaturesof90°C)
230 V 50 Hz 3 x 0,75 mm2 (*) (**)
(*)Connection possible with plug and outlet
(**)Connection with wall box connection.
WARNING: If the power supply cable is damaged, it must be replaced only by an
authorised service agent in order to avoid a hazard.
• The supply cable must be replaced with a cable of the same type.
• The electrical cable must be connected to the terminal board following the diagram of
g. 3.1.
L1 N(L2)PE
Fig. 3.1
230 V 50 Hz

20
Advice for
the users