Elba EGC-A5261SS User manual

For The Warranty Terms & Conditions, Please Refer To Warranty Certificate
Owner’s Manual
Please read this manual carefully before
operating your set.
Retain it for future reference.
Record model number and serial number
of the set.
See the label attached on the set and
quote this information to your dealer
when you require service.
GAS STOVE
MODEL: EGC-A5261SS

REMOVE ALL PACKING MATERIALS FROM THIS PRODUCT BEFORE USING IT. THIS
APPLIANCE MUST BE INSTALLED ON A FLAT SURFACE. PLEASE ENSURE THE GAS
SUPPLY TO THIS APPLIANCE IS DISCONNECTED BEFORE INSTALLING.
Please read this instruction carefully. It is advisable to keep this instruction manual in a safe
place for future reference.
SAFETY PRECAUTIONS
1. Keep cooking appliances out of reach from children. Do not let them to operate the
appliance without supervision.
2. This product must be stationed at least 15cm away from other objects. There should be
100cm space between it and anything on the top.
3. This product is for household and indoor use only.
4. This product is not intended for use by person (including children) with reduced physical,
sensory or mental capabilities unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
5. If the gas hose is damaged, it must be replaced to avoid hazard.
6. This product should be at least 50cm away from gas-cylinder within, the windpipe should
be above 1.5m and should not touch the furnaces stack and across the oven.
WARNING - to reduce the risk of fire or injury to persons or property, please
read and follow below instructions carefully:
Do not operate this product if it has malfunctioned, damaged hose or appears damaged
in any way. Return the complete product to the place of purchase for inspection, repair or
replacement.
This product should not be used in the immediate vicinity of explosive and flammable
where the likelihood of gas leakage could occur.
Make sure the room is well ventilated. It is always recommended to install an exhaust fan
for better ventilation.
If there is gas leakage occurs, please turn off the gas source immediately. Open the door
and window to ventilate the kitchen. Do not use electrical equipment to ventilate the
kitchen and do not operate any electronic equipment or switch.
Always switch off the gas when not in use, before assembling or disassembling parts and
before cleaning.
Fully assemble the gas stove before operating.

OPERATION PROCEDURE AND MODULATON
1. HOW TO STRIKE FIRE
Set the knob to the gas off position and then turn on the
gas source switch. Follow the picture on the right side,
push the knob in 3mm and turn anti-clockwise. You will
hear a click sound at the same time the fire will be lighted,
then you can let go of the knob.
2. POWER MODULATION
You can control the flame by turning the knob to the max or
min position to increase or decrease the intensity of flame.
The pointer of the knob which faces to the wide area is high
intensity; reversely face to the narrow area is low intensity.
3. POWER OFF
To turn off turn the knob clockwise to the off position, the stove will be off automatically.
WARNING: Please turn off the gas source when not in used.
4. AIR INTAKE MODULATION
If the flame becomes unstable, turn the wind switch under
the gas stove to reduce the air intake. If the flame is
burning out of place, use the wind switch under the stove
to regulate it.
CLEANING AND MAINTENANCE
Clean the appliance with a damp cloth with mild cleaner. Do not use chemical, steel, wooden
or abrasive cleaners to clean the appliance.
WARNING: DO NOT IMMERSE THE APPLIANCE INTO WATER. ENSURE THAT THE
GAS SOURCE IS TURNED OFF BEFORE CLEANING THE APPLIANCE.

TROUBLESHOOTING
MAIN SPECIFICATION
Gas Type : LPG
Rated Pressure : 2800 pa
Burner Rating (Left) : 4.3kW
Burner Rating (Right) : 4.3kW
Failure
Failure Reason
Possible Solution
Burner does not light
Gas source was not switched on
Turn on the gas source switch
The gas pipe is leaking
Change a new pipe
Gas depleted
Replace the gas cylinder
Air in the gas pipe
Turn repeatedly to expel air
Mispositioning of the ignition needle
Adjust the discharge distance to
3-4mm
Gas Leakage
Pipe aging and torn off
Change a new gas pipe
Main fire cannot be lighten up
Try again after the gas
dispersed
The gas valve not airproof
Change the valve
Exceptional
Flame
Anomalous
Flame
Gas burner not positioned correctly
Make sure the burner is
positioned correctly
Short Flame
Not enough gas pressure
Inspect the gas cylinder and the
redactor
Long and yellow
flame
Too small intake
Adjust the air intake
Asymmetrical
Flame
The hole of the burner is jammed
Clean the burner