Elba EGS-K6081 User manual

For The Warranty Terms & Conditions, Please Refer To Warranty Certificate
Owner’s Manual
Please read this manual carefully before
operating your set.
Retain it for future reference.
Record model number and serial number
of the set.
See the label attached on the set and
quote this information to your dealer when
you require service.
SEMI-COMMERCIAL
GAS STOVE
MODEL: EGS-K6081(SS)

Please read this instruction carefully. It is advisable to keep this instruction manual in
a safe place for future reference.
SAFETY PRECAUTIONS
1. Keep the appliances out of reach from children. Do not let them to operate the
appliances without supervision.
2. This product is for household and indoor use only.
3. This product is not intended for use by person (including children) with
reduced physical, sensory or mental capabilities unless they have been given
supervision or instruction concerning use of the appliances by a person
responsible for their safety.
4. If the gas hose, hose clamp and regulator are damaged, it must be replaced by
the service centre or a qualified service technician to avoid hazard.
5. There must be adequate air ventilation of the room when the product is used.
6. This appliances must be stationed at least 15cm away from other objects.
There should be 100cm space between it and anything on the top. This
appliances should be at least 50cm away from gas cylinder.
7. There is a risk of fire if cleaning is not carried out in accordance with this
instruction.
8. Do not touch the gas stove surface during or after cooking with bare hand.
9. Before maintenance or cleaning, switch off the main gas valve and disconnect
the gas stove from the gas cylinder. Please make sure there is no gas leakage
before maintenance or cleaning.

10. Do not store or place flammable liquids or items in the vicinity of this gas
stove.
11. Always switch off the gas when not in use, before assembling or
disassembling parts.
12. Caution: Use only low pressure regulator for this appliance.
DESCRIPTION OF THE GAS STOVE
1. Trivet 6. Front Panel
2. Burner 7. Body Casing
3. Top Plate 8. Rubber Stand
4. Left Ignition Knob
5. Right Ignition Knob

INSTALLATION FOR USE
1. Check the gas stove to ensure all parts are complete.
2. Using a screwdriver affix the rubber legs with screw provided into the
designated hole on the bottom of the gas stove.
3. Connect the gas hose (not included) onto the inlet pipe.
4. Using a screwdriver, secure the gas hose and inlet pipe by tighten the hose
clamp.
5. Place the trivet on top of the burner.
6. Open the main gas valve on the gas cylinder. If there is gas leakage detected,
close the main gas valve immediately and open the windows to allow the gas
to escape from the room.

INSTRUCTIONS FOR USE
1. The left ignition knob is control on the outer flame and the right ignition knob
is control on the inner flame. The inner and outer burner can operate
separately by turn on the related ignition.
2. Open the main gas valve and turn the ignition knob anti clockwise direction
until the ignition click sound appear and flame is lighted.
3. If the flame fails to ignite, turn the ignition knob back to “OFF” position and
repeat the procedure as point 1.
4. In order to obtain the best flame output, adjust the damper under the gas stove
either clockwise or anti clockwise direction until the blue color flames are
obtained.
Example:
Perfect amount of air
The flame is transparent blue and the difference between the inner flame and
the outer can be clearly seen.
Insufficient air
The flame turn red and burns like a handle and unstable.
Too much air
The flame is short and flutters.
5. Turn the ignition knob back to “OFF” position to turn off the gas stove.

CLEANING AND MAINTENANCE
Clean the appliance with a damp cloth with mild cleaner. Do not use chemical, steel,
wooden or abrasive cleaners to clean the appliance. Wash the trivet in water. Use a
brush for cleaning the burner.
TROUBLESHOOTING
Failure
Failure Reason
Possible Solution
Burner does not light
Gas source was not
switched on
Turn on the gas
source switch
The gas pipe is leaking
Change a new pipe
Gas depleted
Replace the gas cylinder
Air in the gas pipe
Turn repeatedly to expel
air
Mispositioning of the
ignition needle
Adjust the discharge
distance
to 3-4mm
Gas Leakage
Pipe aging and torn off
Change a new gas pipe
Main fire cannot be
lighten up
Try again after the gas
dispersed
The gas valve not airproof
Change the valve
Exceptional
Flame
Anomalous
Flame
Gas burner not positioned
correctly
Make sure the burner is
positioned correctly
Short Flame
Not enough gas pressure
Inspect the gas cylinder
and the regulator
Long and yellow
flame
Too small intake
Adjust the air intake
Asymmetrical
Flame
The hole of the burner is
jammed
Clean the burner

MAIN SPECIFICATION