Eldorado Stone OLPLSFP04 Installation instructions

THE BUILDING BLOCKS FOR LUXURY OUTDOOR SPACES.
33"
40"
33" 39"
13"24"
15"
30"
66"
48"
9"
21"
6"
16"
36"
82"
13"
33"
40"
33" 39"
13"24"
15"
30"
66"
48"
9"
21"
6"
16"
36"
82"
13"
PART NUMBER DESCRIPTION ILLUSTRATION
OLPLSFP04-1 Left Side Hearth
OLPLSFP04-2 Right Side Hearth
OLPLSFP04-3 Left Side
Column
OLPLSFP04-4 Right Side
Column
OLPLSFP04-5 Mantel Section
OLPLSFP04-6 Chimney Section
OLPLSFP04-7 Back Panel
OLPLSFP04-8 Front Plate
OLPLSFP04-A
Right Side
Firebox Insert
Panel
PART NUMBER DESCRIPTION ILLUSTRATION
OLPLSFP04-B
Left Side
Firebox Insert
Panel
OLPLSFP04-C Rear Firebox
Insert Panel
OLPLSFP04-21 Metal Flue Liner
Bottom Section
OLPLSFP04-22
Metal Flue Liner
Top Section with
Spark Arrester
OLPLSFP06 Hearth Extension
OLPW81633 Hearth Extension
Backrest
OLPLSFP05 Chimney Extension
with Metal Flue Liner
INSTALLATION / OPERATION INSTRUCTIONS
Model OLPLSFP04 Outdoor Fireplace

Page 2of 12
www.eldoradostone.com/outdoor
|
1.800.925.1491
WARNINGS
O       
      .
T          
  ,          .
T         .
T     ,    .
W  ,      
       .
D      , ,   
  . T    
        
        .
D   .
T          .
T     ,     .
D         .
INSTALLATION / OPERATION INSTRUCTIONSModel OLPLSFP04 Outdoor Fireplace

Page 3of 12
www.eldoradostone.com/outdoor
|
1.800.925.1491
PRODUCT USAGE
The OLPLSFP is designed to burn solid woods or gas outdoors. This unit is not
designed to sit directly against combustible materials. This unit is not designed to be
built into a wood structure. The Eldorado Outdoor model number OLPLSFP is
designed as an outdoor unit only.
The OLPLSFP is shipped with the appropriate flue liner and has been tested to
comply with UL-/ ULC-S.
Use solid wood, plumbed propane or natural gas fuel only.
Gas log appliances used with this product must be approved for outdoor use.
MODIFICATION OF FIREPLACE
The addition of extensions may be accomplished by using the Eldorado Outdoor
extensions (shown on the first page), metal aming or concrete block. There is no
clearance or airspace required when using extensions, metal aming or concrete block.
CHIMNEY EXTENSIONS
The standard height of . in.is the height tested to achieve proper dra characteristics.
If conditions exist that require additional chimney height, please follow all local building
codes and regulations during installation.
The addition of the concrete extension OLPLSFP requires an additional flue
liner which is included in OLPLSFP. A maximum of two OLPLSFP Chimney
Extensions can be used on top of the OLPLSFP Chimney Section.
If a prefabricated metal chimney is chosen, it must be tested and found compliant with
UL-. It must be installed in accordance with chimney manufacturer’s instructions
and use all necessary parts specified for use with the listed chimney system.
Chimney termination must be a minimum of  . above any combustible structure
within  . of the chimney termination.
INSULATION
This product is not designed to be “packed” by insulation. In the event air spaces exist
between this product and CMU or metal aming construction, do NOT fill these voids
with an insulating product.
INSTALLATION / OPERATION INSTRUCTIONSModel OLPLSFP04 Outdoor Fireplace

Page 4of 12
www.eldoradostone.com/outdoor
|
1.800.925.1491
PRODUCT USAGE
VENTILATION
The OLPLSFP is designed as an outdoor unit only. No additional ventilation or
circulation is required.
MANTEL CLEARANCES
A decorative mantel may be installed above the opening of a
Model OLPLSFP Fireplace providing the ont edge of the
mantel is no more than  in. om the face of the fireplace
and a minimum of  in. above the opening.
CLEARANCES
The distances to combustibles while burning solid wood shall be no less than  in.
om the ont of firebox,  in. om the side walls and  in. om the back wall. When
a UL approved , BTU vent-ee gas log set is used and the top of the chimney
capped, the clearances shall be no less than  in. om the ont,  in. om the back
and  in. om the top of the chimney.
DAMAGED PARTS
If unit is delivered with obvious damage due to eight, please notify driver or refuse
delivery. If product is damaged on job site, you may be able to repair unit using
adhesive and/or mortar. If damage is severe, contact your dealer to arrange shipment
of replacement parts.
MAINTENANCE
Please contact a professional chimney sweep at least once each year to inspect and
make recommendations regarding the maintenance of your outdoor fireplace. In the
event you have added a decorative chimney termination or rain cap to your fireplace,
please be prepared to inform the chimney sweep as to the best method to perform
proper inspection/maintenance.
10"
12"
Firebox
Mantel
Fireplace
Prole
INSTALLATION / OPERATION INSTRUCTIONSModel OLPLSFP04 Outdoor Fireplace

Page 5of 12
www.eldoradostone.com/outdoor
|
1.800.925.1491
INSTALLATION GUIDELINES
STEP 1: HEARTH ( L/R )
A) Place the Hearth sections next to each other in their
final installation location.
B) Li the Hearth sections onto the ont edges to
access them om underneath.
C) Apply construction adhesive between the Hearth
sections and push them together, being sure to line
up the bolt holes.
D) Insert  bolts with  washers and  nuts. Tighten a
¼ turn past snug.
E) Lay the Hearth down and slide into position. Use shims
if necessary to level the Hearth
STEP 2: HEARTH EXTENSIONS
(IF APPLICABLE)
A) Place a Hearth Extension next to the assembled
Hearth. Make sure the  bolt holes on top of the
Hearth Extension are at the back of the Hearth.
B) Apply construction adhesive to the Hearth Extension
side wall and adhere to the Hearth.
C) Using the access holes in the Hearth and the Hearth
Extension, insert  bolts with  washers and  nuts.
Tighten a ¼ turn past snug.
D) Repeat on the other side if using two Hearth
Extensions.
E) Use shims to level the completed Hearth, if necessary.
First make sure your installation surface is clean and stable. If needed, use shims to level the fireplace during
installation.
The unit can be placed on a  in. concrete slab or a paver patio that has been installed following ICPI (Interlocking
Concrete Paver Institute) guidelines.
INSTALLATION / OPERATION INSTRUCTIONSModel OLPLSFP04 Outdoor Fireplace

Page 6of 12
www.eldoradostone.com/outdoor
|
1.800.925.1491
INSTALLATION GUIDELINES
STEP 3: COLUMNS / LEGS ( L/R )
A) Apply construction adhesive around the access hole on
top of the Hearth section where the column will sit.
B) Place the column over the access hole with the open
side facing inward, being sure to line up the bolt holes.
C) Reaching through the column and into the Hearth
base, insert  bolts with  washers and  nuts.
Tighten a ¼ turn past snug.
D) Repeat on the opposite side.
STEP 4: BACK PANEL (EXTERIOR)
A) Insert Back Panel between two side Columns/Legs.
B) Apply construction adhesive where the pieces connect
and line up using bolt holes.
C) Use four 6” bolts included.
D) Insert  bolts with  washers and  nuts. Be sure the
bolts extend into the column leaving the Back Panel
open to accept the Rear Reactory Panel in step .
E) Tighten bolts a ¼ turn past snug.
STEP 5: HEARTH BACKREST
EXTENSIONS (IF APPLICABLE)
A) Apply construction adhesive to the top of the Hearth
Extension where the Hearth Backrest Extension will
be placed. The open side of the backrest should face
upward when installed.
B) Place Backrest Extension on top of Hearth Extension
and line up bolt holes.
C) Insert  bolts,  washers and  nuts through the
holes at the bottom of the backrest section.
D) Reach through the Hearth Extension access holes to
tighten nuts ¼ turn past snug.
E) Apply adhesive to the beveled edge of the lid provided
and set in place to close off the top of the unit.
INSTALLATION / OPERATION INSTRUCTIONSModel OLPLSFP04 Outdoor Fireplace

Page 7of 12
www.eldoradostone.com/outdoor
|
1.800.925.1491
INSTALLATION GUIDELINES
STEP 6: REAR REFRACTORY PANEL
A) Tack the panel in place by applying construction
adhesive to the backside (corners only) of the Rear
Reactory Panel.
B) Insert panel through fireplace opening with scratch
coat facing out. Place foot of Reactory Panel on
top of the Back Panel footing. The Rear Reactory
Panel fits inside the Back Panel.
STEP 7: MANTEL SECTION
A) Apply construction adhesive to the top of the Legs
and the Back Panel (exterior).
i) Do not apply adhesive along the top of the Rear
Reactory Panel. It should remain clean to
accept the Metal Flue Liner Bottom Section in
step .
B) Place the Mantel Section on top of the unit lining
up the bolt holes. The smaller opening should be up
and at the back of the fireplace unit.
C) Insert  bolts,  washers, and  nuts in the holes at
the top of the Legs. Access these bolt holes through
the firebox and the open Legs.
D) Tighten bolts a ¼ turn past snug.
STEP 8: FRONT PLATE
A) Apply construction adhesive to the top of the Front
Plate (side with bolt holes).
B) Install Front Plate between the Legs and against the
bottom of the Mantel Section.
C) Line up bolt holes and add  bolts,  washers, and 
nuts by accessing om inside the fireplace opening.
D) Tighten a ¼ turn past snug.
INSTALLATION / OPERATION INSTRUCTIONSModel OLPLSFP04 Outdoor Fireplace

Page 8of 12
www.eldoradostone.com/outdoor
|
1.800.925.1491
INSTALLATION GUIDELINES
STEP 9: METAL FLUE LINER –
BOTTOM SECTION
A) Make sure the Rear Reactory Panel is adhered, or
supported. This flue section will rest on top of the
Rear Reactory Panel and the Side Firebox inserts.
The Side Firebox inserts install in Step .
B) Remove the provided sheet metal screws om the
ont of the Flue Liner before installing.
C) Go through the fireplace opening with the long
back flange facing up and inward (the ont of the
flue has no flange). Use the openings in the Legs
to maneuver the flue through the fireplace opening.
D) Rest the back flange of the Flue Liner on the top of
the Rear Reactory Panel
E) Push the Flue Liner up and hold in place while
another person completes Step .
STEP 10: SIDE FIREBOX INSERT
PANELS (2)
A) Place the foot of the Side Insert Panel at the base of
the Leg opening.
B) Tack the panel in place by applying construction adhesive
to the backside (corners only).
C) Press the Side Firebox Insert Panel into place.
D) Repeat on the opposite side.
STEP 11: CHIMNEY SECTION
A) Center the Metal Flue Liner Bottom Section (installed
in Step ) within the Mantel Section opening on the
top of the fireplace.
B) Add adhesive to the top of the Mantel Section where the
Chimney Section will be placed.
C) Li Chimney Section into place and line up bolt holes.
D) Add  bolts,  washers and  nuts and then tighten a
¼ turn past snug.
INSTALLATION / OPERATION INSTRUCTIONSModel OLPLSFP04 Outdoor Fireplace

Page 9of 12
www.eldoradostone.com/outdoor
|
1.800.925.1491
INSTALLATION GUIDELINES
STEP 12: CHIMNEY EXTENSION
(IF APPLICABLE)
A) Chimney Extension
i) Add adhesive to the top of the Chimney Section
where the Chimney Extension will be placed.
ii) Li the Chimney Extension into place and line
up bolt holes.
iii) Add  bolts,  washers and  nuts and then
tighten a ¼ turn past snug.
B) Metal Flue Liner Extension
i) When adding a Flue Liner extension, connect the
two Metal Flue Liners together as described below.
ii) Place the Metal Flue Liner Extension (the one
without the spark arrester) on the bottom and
the regular Metal Flue Liner Top Section (with
spark arrester) on top.
iii) Use the  sheet metal screws provided to attach
the two sections together om the inside.
STEP 13: METAL FLUE LINER –
TOP SECTION(S)
A) Insert Flue Liner Top Section (with the spark
arrester at the top) through the top opening of the
Chimney Section. If using a Chimney Extension,
this will be two Flue Liners connected as one with
the spark arrester on the top section.
B) Enter through the fireplace and connect the Flue Liner
Top Section to the Flue Liner Bottom Section using
() sheet metal screws provided.
INSTALLATION / OPERATION INSTRUCTIONSModel OLPLSFP04 Outdoor Fireplace

Page 10 of 12
www.eldoradostone.com/outdoor
|
1.800.925.1491
INSTALLATION GUIDELINES
STEP 14: FIRE BRICK
(NOT PROVIDED)
A) Line the fireplace base and firebox with fire brick.
B) We recommend full dimension fire brick on the bottom
and split fire brick on the sides and rear wall.
C) Fire brick on the bottom should be dry set to allow
for drainage.
D) Rough Dimensions for Fire Brick:
Hearth Base  . SF
Back and Side Walls   SF (depending on height of
your Hearth base material)
STEP 15: EXTERIOR FINISH
(NOT PROVIDED)
A) Finish exterior of the Eldorado Outdoor Wood
Burning Fireplace with Eldorado Stone, Eldorado
Brick, natural veneer or stucco.
INSTALLATION / OPERATION INSTRUCTIONSModel OLPLSFP04 Outdoor Fireplace

Page 11 of 12
www.eldoradostone.com/outdoor
|
1.800.925.1491
OPERATING INSTRUCTIONS
This part of the manual covers methods to maximize the performance of your Eldorado
Outdoor fireplace. If you are having trouble with your Eldorado Outdoor unit, please
contact your installer or call --- for assistance.
Use a log grate to place under the fuel when using solid wood fuels. We recommend
using hardwood dried  to  months for best results. Place wood in firebox with
ample air space between logs.
BUILDING A FIRE
Start by placing some kindling in the center of your fireplace grate (see callout “A” in
illustration below). Then lay one split section of log across each side of the kindling (“B”),
placing the pieces of wood so that the ends nearer to the back of the fireplace (“C”) are
closer together than the ends at the ont. The wood should not extend more than an
inch beyond the ont of the grate or it may cause smoke to move out the ont of the
unit. Now lay an additional one or two pieces of wood across the two side logs (“D”).
Push these top logs all the way to the back (“E”) so the rearmost lies against the rear
wall of the fireplace.
INSTALLATION / OPERATION INSTRUCTIONSModel OLPLSFP04 Outdoor Fireplace
(A)Kindling
(B)Split Logs
(C)(C)Move ends in back
closer together
(D)Additional Wood
(E)Push wood to touch
rear interior wall

Page 12 of 12
www.eldoradostone.com/outdoor
|
1.800.925.1491
Eldorado Stone®LLC, 1370 Grand Ave. B, San Marcos, CA 92078
11 0 7 11
OPERATING INSTRUCTIONS
DISPOSAL OF ASHES
• Keep the base of the replace clean of excess ash accumulation. This will prevent
grate “burn-out.”
• Keep the area directly underneath the burning logs ee of ash. Make sure ash does
not build up to a point where it hinders the air flow.
• Before removal, make sure the re is completely out and the ashes cool.
• Use a small replace shovel to remove accumulated ash.
• Place the ashes in a metal container with tight-tting lid and store the closed container
on a non-combustible oor surface. Keep it well away om all combustible materials
until final disposal. Dispose of the ash by burying it in soil or other local dispersal.
Make sure ash is retained in the closed container until cinders have thoroughly cooled.
• Replace any grate that has deteriorated, distorted or sagged om extended use.
INSTALLATION / OPERATION INSTRUCTIONSModel OLPLSFP04 Outdoor Fireplace