ELECANE DC-656 User manual

ELECANE SMALLEST
BARK COLLAR
MODEL DC-656
PRODUCT MANUALPRODUCT MANUAL
Thank you for purchasing the Elecane Bark Collar.
The product has been specially developed for small
dogs and their owners.
Dear dog lovers, our company and its employees love
pets and don't want to do any harm to them. That's
why only humane ways of influence, such as sound
warning and vibration, are used in our bark correction
collars.
Based on different testing models of the Elecane,
it achieves an efciency of 75-80% with the dogs
that stopped barking within one week. 10-15% of
dogs need up to two weeks, and about 5% of dogs
need more time. Unfortunately, 3-5% of dogs aren't
susceptible to bark correction through exposure to
sound and vibration.
| 1

If our product didn't help you solve the problem with
excessive barking, don't hesitate to contact our
support team at suppor[email protected], and we will
help you or reimburse the purchase.
The main element of the Elecane bark collar is the
sensor. It recognizes and detects your dog’s throat
vibration (barking).
Thesensor detects barking,andthecollarisactivated,
affecting the dog with a vibro-sound warning.
The impact of the collar on
each dog can vary as each
dog has a different level of
sensitivity to it, and it also
depends on the sensitivity,
thickness, and structure
of the skin, fat, muscles,
nervous excitability, etc.
PRINCIPLE OF OPERATION
IMPORTANT!
IMPORTANT!
In accordance with the requirements of humanity
the Elecane Bark Collar has a special system of
restrictions for the duration and intensity of exposure
to the dog.
| 2

CORRECTION
LEVELS OF
1st bark
2nd bark
3rd bark
4th bark 8th bark
5th bark
6th bark
7th bark
1.5 secs
1.5 secs
5 secs
5 secs
5 secs
5 secs
5 secs
1 secs
1.5 secs
2 secs
3 secs
4 secs
Sleep mode. For
the dog’s safety
the collar turns off
for 1 minute.
| 3
1st bark: sound for 1.5 seconds
2nd bark: sound for 2.5 seconds
3rd bark: sound for 5 seconds + vibration for 1
second
4th bark: sound for 5 seconds + vibration for 1.5
seconds
5th bark: sound for 5 seconds + vibration for 2
seconds

IMPORTANT!
To turn ON/OFF the collar, press the button for 3
seconds still until the collar beeps and the indicator
lights up.
OVERVIEW
DEVICE
Charging Socket Blow into the small hole Indication Light
Vibration Prongs High Low On/Off
Switch
| 4
6th bark: sound for 5 seconds + vibration for 3
seconds
7th bark: sound for 5 seconds + vibration for 4
seconds
8th bark: Sleep mode. For the dog’s safety the collar
turns off for 1 minute.
1. The collar moves to the next correction level
consistently and only if the dog continues to bark.
If the dog does not bark for 30 seconds, the collar
returns to the rst correction level.
2. After ‘sleep mode’ activation, the collar returns to
the rst correction level.
IMPORTANT!

USAGE
THE FIRST
1. To charge collar 1.5-2 hours.
2. Turn on the collar before use. Press the
button and hold for 3 seconds. The collar will
beep, and the indicator will turn green.
3. Set the collar’s sensitivity to position 4. Press
the button a short while until the collar ceases
to emit a signal when the button is pressed. It will
be the mode of the lowest sensitivity of the collar.
Then press the button. three times, which will
be mode 4.
• Each time you press the button, the collar will
sound like a beep, so you know that the mode
has switched. Adjust the sensitivity if necessary.
For the collar to start working:
| 5

| 6
1. Check whether the collar ts tightly or not. If
necessary, adjust it. You must cut the excess strap.
2. Install the collar block in the middle of the strap.
Note that the collar block moves along the strap
as you pull on it.
3. You must put the collar on the dog so the block is
in the center of the throat. The collar reacts to the
vibration of the throat when the dog barks.
How to put a collar on a dog:
IMPORTANT!
Read on for more details and features of use!
The collar needs to be charged when the red light
continues flashing slowly for 30sec and then turns
off automatically.
1. Open the Battery Charging Rubber Cover on the
Anti Bark Collar, plug one end of the cable in the
charging port and connect the other end to the
adaptor, computer, notebook, or power bank.
(Note: please make sure that the adaptor output is
5V/500 - 1000mAh.)
2. Plug the Lithium Polymer Charger into an electrical
power outlet of standard household voltage (110-
230V) based on your local standard.
3. The red light will be steady when fully charged
within 1.5 to 2 hours. It turns green light when
charged fully.
INSTRUCTION
CHARGING

| 7
IMPORTANT!
The work time of the battery can vary depending on
the frequency of the collar activation.
Take the collar in your hands, facing the back side of
the collar, and gently blow a small puff of air towards
the small hole between the vibration prongs. You will
hear a sound.
Blow a puff of air again. You will hear the second
sound.
Blow for the third time, and you will hear a sound
and feel a mild vibration (similar to the cell phone
vibration).
You may continue to do this till the 7th correction
level is reached.
Charging time: 1.5-2 hours
Work time: The battery charge
lasts up to 14 days with
ordinary use.
Time of non-stop working: 6-7
hours
BEFORE USING
TESTING THE COLLAR
Press and hold for 3
seconds
Adjust sensitivity
Press to adjust
the sensitivity
Blowing into a
small hole
Sound Vibrate

| 8
SENSITIVITY
ADJUSTING THE
There are two BUTTONS , which are used to
adjust the sensitivity.
The higher the sensitivity level is, the easier it is to
trigger the collar.
Press the button for a short while until the collar
ceases to emit a signal when the button is pressed.
It will be the mode of the lowest sensitivity of the
collar (the 1st). Then press the button three times,
which will be mode 4.
Each time you press the button, the collar will sound
like a beep, so you know that the mode has switched.

| 9
ON THE DOG
PUT THE COLLAR
It would be best if you found the sensitivity level of
your dog by experimentation.
After turning off and turning back on the collar your
settings will remain.
IMPORTANT!
The correct placement and settings of the collar are
essential for its effective work.
1. If the icon is blinking, the battery is not charged.
Please charge the device.
2. Put the dog in a comfortable position that allows
you to apply the collar correctly.
3. Install the collar receiver (main body) in the middle
of the strap. Note that the collar receiver moves
along the strap as you pull on it. Put the collar on
your dog - high under the jaw and tighten the strap.
The collar’s receiver must be located precisely in
the middle of the neck, one inch below your dog’s
Adam’s apple.
4. For your dog’s comfort in wearing the collar, please
adjust the strap correctly. Put the collar on the
dog, and leave a couple of inches so that the collar
will t your dog’s neck as it grows or has thick fur.
Then take it off, cut off the excess and burn the
cut with re for a couple of seconds. For your pet’s
safety, please do it out of your dog’s reach.
5. If the dog’s hair on the throat is long, it must be
shortened for the collar to work correctly.

| 10
6. Let your dog wear the collar for a couple of minutes
and then check again if it ts well. When the dog
gets used to the collar, double-check the correct
placement of the collar.
IMPORTANT!
If you don’t tighten the strap tight enough, it won’t
work correctly. There will be no contact, besides, it
can rub the dog’s neck. To check the collar’s t, insert
your nger between the end of the contact points and
the dog’s neck. The nger should be snug, but the dog
should not experience breathing problems. In some
cases, it may be necessary to shorten the fur around
the contact point for direct contact.

| 11
How to turn ON/OFF on the collar?
To turn ON/OFF the collar, press the (картинка кнопки
включения) button for 3 seconds still until the collar
beeps and the indicator lights up.
Is the collar waterproof?
Yes, it is. You can use the collar in any weather
condition.
Is the collar rechargeable, or do I need batteries?
The current model of the bark collar is rechargeable.
Use the USB cable with the device and charge it via
PC, laptop, or adapter.
I’ve got two dogs. If I use the bark collar with one
dog, will it activate when the other dog barks?
No, it won’t. The bark collar has a special protection
system from false detection, and the sensor detects
and recognizes the throat vibration of the dog to
which it is initially set.
My dog barks, but the collar is not activated. Why?
Check the battery and perform a full test. If the
collar tests correctly, you will need to either increase
the sensitivity level by pressing to make it easier to
activate or tighten the collar as it might be too loose.
FAQ
If our product didn't help you solve the problem with
excessive barking, don't hesitate to contact our
support team at suppor[email protected], and we will
help you or reimburse the purchase.
IMPORTANT!