Electro-Harmonix NANO BASS BIG MUFF PI User manual

FCC COMPLIANCE
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the CC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Modifications not expressly approved by the manufacturer could void the user's
authority to operate the equipment under CC rules.
NANO BASS BIG MUFF PI
Congratulations! You have just purchased the finest harmonic distortion-
sustain device for the electric bass guitar player, now in a smaller enclosure:
the Nano Bass Big Muff! Please review this manual to learn the unique
potential of this pedal.
The Nano Bass Big Muff draws its roots from the legendary Sovtek battle-
tank green Big Muff Pi manufactured in the ‘90s as well as from the original
Electro-Harmonix Big Muff Pi from the early ‘70s. These Big Muffs are often
employed by bass players to thicken up their sound or to give them over-
the-top low end growl. The Nano Bass Big Muff takes the best characteristics
from both of these classics and employs sonic elements that were specifically
designed for your bass.
-OPERATING INSTRUCTIONS-
SUSTAIN Knob — adjusts the amount of sustain and distortion.
TONE Knob — provides a range of sounds from high treble to deep bass. As
you turn the knob clockwise, treble increases and bass decreases.
VOL Knob — sets the output level of the distortion effect. When the toggle
switch is set to DRY, the volume knob has no effect on the output level of
the dry signal.
DRY Toggle Swi ch — when set to DRY mode, the original dry signal
present at the input jack is mixed with the output of the distortion circuit.
The level of the Dry signal is constant and will not change as you turn the
Volume knob up or down allowing you to set the level of the distortion effect
against your dry signal. lip the DRY switch to the left, away from the DRY
label, to mute the dry signal; now you will hear only Big Muff distortion.
Foo swi ch & S a us LED — When the LED is lit, the Nano Bass Big Muff
effect is active. When the LED is off, the Nano Bass Big Muff is in True
Bypass mode. The ootswitch toggles between effect and bypass modes.

INPUT Jack – This ¼” jack is the audio input to the Nano Bass Big Muff.
The input impedance presented at this jack is 110 kΩ.
AMP Jack – This ¼” jack is the audio output from the Nano Bass Big Muff.
When the Nano Bass Big Muff is in True Bypass mode, the AMP jack is
connected directly to the INPUT jack.
9V Power Jack – The Nano Bass Big Muff Pi is powered from a 9V battery
or you can use an optional 9VDC AC Adapter capable of delivering at least
25mA to the 9V power jack, such as the EHX9.6DC-200. The AC Adapter
must have a center negative plug. The battery may be left in or taken out
when using an AC Adapter. The Nano Bass Big Muff has a current draw of
approximately 4mA at 9VDC.
We recommend he Elec ro-Harmonix US96DC-200BI
9.6VDC/200mA AC Adap er o power your Nano Big Muff Pi.
-CHANGING THE BATTERY-
To change the 9-Volt battery, you must remove the 4 screws on the bottom
of the Nano Bass Big Muff Pi. Once the screws are removed, you can take off
the bottom plate and change the battery. Please do not touch the circuit
board while the bottom plate is off or you risk damaging a component.
- WARRANTY INFORMATION -
Please register online at http://www.ehx.com/product-registration or complete and
return the enclosed warranty card within 10 days of purchase. Electro-Harmonix will
repair or replace, at its discretion, a product that fails to operate due to defects in
materials or workmanship for a period of one year from date of purchase. This
applies only to original purchasers who have bought their product from an authorized
Electro-Harmonix retailer. Repaired or replaced units will then be warranted for the
unexpired portion of the original warranty term.
If you should need to return your unit for service within the warranty period, please
contact the appropriate office listed below. Customers outside the regions listed
below, please contact EHX Customer Service for information on warranty repairs at
[email protected] or [phone]. USA and Canadian customers: please obtain a
Re urn Au horiza ion Number (RA#) from EHX Customer Service before returning
your product. Include with your returned unit: a written description of the problem
as well as your name, address, telephone number, e-mail address, and RA#; and a
copy of your receipt clearly showing the purchase date.
Uni ed S a es & Canada
EHX CUSTOMER SERVICE
ELECTRO-HARMONIX
c/o NEW SENSOR CORP.
55-01 2ND STREET
LONG ISLAND CITY, NY 11101
Tel: [phone]
Email: [email protected]
Europe
JOHN WILLIAMS
ELECTRO-HARMONIX UK
13 CWMDONKIN TERRACE
SWANSEA SA2 0RQ
UNITED KINGDOM
Tel: [phone]
Email: [e-mail]
This warranty gives a purchaser specific legal rights. A purchaser may have even
greater rights depending upon the laws of the jurisdiction within which the product
was purchased.
To hear demos on all EHX pedals visit us on the web at www.ehx.com
Email us at [email protected]