Electrolux Professional Compass Pro TD6-10 User manual

Installation manual
Tumble dryer
TD6–10
Compass Pro
Type N1190..
Original instructions
438917562/EN
2022.09.12

Contents
Contents
1 Safety Precautions ..............................................................................................................................5
1.1 Gas heated tumble dryer: ...........................................................................................................7
1.2 General safety information..........................................................................................................7
1.3 Commercial use only..................................................................................................................7
1.4 Copyright ..................................................................................................................................7
1.5 Symbols....................................................................................................................................8
2 Warranty terms and exclusions.............................................................................................................9
3 Technical data...................................................................................................................................10
3.1 Drawing ..................................................................................................................................10
3.2 Technical data ......................................................................................................................... 11
3.3 Connections ............................................................................................................................ 11
3.4 Machines with heat pump .........................................................................................................12
3.4.1 Drawing.........................................................................................................................12
3.4.2 Technical data................................................................................................................13
4 Setup ...............................................................................................................................................14
4.1 Unpacking...............................................................................................................................14
4.1.1 Machines with heat pump................................................................................................14
4.2 Recycling instruction for packaging ...........................................................................................15
4.3 Siting ......................................................................................................................................16
4.4 Drain connection (only for machines with heat pump) .................................................................17
4.5 Water connection (only for machines with heat pump).................................................................17
4.6 Mechanical installation .............................................................................................................18
5 Marine installation .............................................................................................................................19
6 Evacuation system ............................................................................................................................20
6.1 Air principle .............................................................................................................................20
6.1.1 For machines with heat pump..........................................................................................20
6.2 Fresh air..................................................................................................................................20
6.3 Exhaust duct ...........................................................................................................................21
6.4 Shared exhaust duct ................................................................................................................21
6.5 Exhaust dimensioning ..............................................................................................................22
6.6 Adjusting the dryer (not valid for machines with heat pump).........................................................22
7 Gas connection .................................................................................................................................23
7.1 Fasten the label .......................................................................................................................23
7.2 General...................................................................................................................................23
7.3 Gas installation........................................................................................................................24
7.4 Table of pressure and adjustment..............................................................................................24
7.5 Test run...................................................................................................................................26
7.6 Converting instructions.............................................................................................................26
7.7 Data label................................................................................................................................28
8 Electrical connection..........................................................................................................................29
8.1 Electrical installation ................................................................................................................29
8.2 Single-phase connection ..........................................................................................................29
8.3 Three-phase connection...........................................................................................................31
8.4 Electrical connections ..............................................................................................................32
8.5 Functions for I/O-cards.............................................................................................................33
8.5.1 Central payment (2J) ......................................................................................................33
8.5.2 Central payment (2J) ......................................................................................................34
8.5.3 External coin meter/Central payment (2K) ........................................................................35
8.5.4 Price reduction (2K)........................................................................................................36
8.6 Option.....................................................................................................................................36
8.6.1 External connection 100 mA............................................................................................36
9 Reversing the door ............................................................................................................................37
10 At first power up ................................................................................................................................39
10.1 Select language.......................................................................................................................39
10.2 Set time and date.....................................................................................................................39
10.3 Activate/Deactivate the service alarm ........................................................................................39
11 Function check..................................................................................................................................40
12 Disposal information..........................................................................................................................41
12.1 Disposal of appliance at end of life ............................................................................................41
12.2 Disposal of packing..................................................................................................................41

Contents
The manufacturer reserves the right to make changes to design and component specifications.

Installation manual 5
1 Safety Precautions
• Servicing shall be carried out only by authorized personnel.
• Only authorized spare parts, accessories and consumables shall be used.
• The machine is not to be used if industrial chemicals have been used for cleaning.
• Do not dry unwashed items in the machine.
• Items that have been soiled with substances such as cooking oil, acetone, alcohol, pet-
rol, kerosene, spot removers, turpentine, waxes and wax removers should be washed
in hot water with an extra amount of detergent before being dried in the machine.
• Items such as foam rubber (latex foam), shower caps, waterproof textiles, rubber
backed articles and clothes or pillows fitted with foam rubber pads should not be dried
in the machine.
• Fabric softeners or similar products should be used as specified by the fabric softener
instructions.
• The final part of a drying cycle occurs without heat (cool down cycle) to ensure that the
items are left at a temperature that ensures that the items will not be damaged.
• Remove all objects from pockets such as lighters and matches.
• WARNING. Never stop the machine before the end of the drying cycle unless all items
are quickly removed and spread out so that the heat is dissipated.
• Adequate ventilation has to be provided to avoid the back flow of gases into the room
for appliances burning other fuels, including open fires.
• Exhaust air must not be discharged into a flue which is used for exhausting fumes from
appliances burning gas or other fuels.
• The machine must not be installed behind a lockable door, a sliding door or a door with
a hinge on the opposite side to that of the machine in such a way that a full opening of
the machine is restricted.
• If the machine has a lint trap this has to be cleaned frequently.
• The lint must not be accumulated around the machine.
• DO NOT MODIFY THIS APPLIANCE.
• When performing service or replacing parts, the power must be disconnected.
• When the power is disconnected, the operator must see that the machine is discon-
nected (that the plug is removed and remains removed) from any point to which he has
access. If this is not possible, due to the construction or installation of the machine, a
disconnection with a locking system in the isolated position shall be provided.
• In accordance with the wiring rules: mount a multi-pole switch prior to the machine to
facilitate installation and service operations.
• Stationary appliances not fitted with means for disconnection from the supply mains
having a contact separation in all poles that provide full disconnection under overvolt-
age category III, the instructions state that means for disconnection must be incorpo-
rated in the fixed wiring in accordance with the wiring rules.
• WARNING: The appliance must not be supplied through an external switching device,
such as a timer, or connected to a circuit that is regularly switched on and off by a utility.
• If different rated voltages or different rated frequencies (separated by a /) are stated at
the machine data plate, instructions for adjusting the appliance for operation at the re-
quired rated voltage or rated frequency are stated in the installation manual.
• The openings in the base, shall not be obstructed by a carpet.

6Installation manual
• Oil-affected items can ignite spontaneously, especially when exposed to heat sources
such as in a tumble dryer. The items become warm, causing an oxidation reaction in
the oil. Oxidation creates heat. If the heat cannot escape, the items can become hot
enough to catch fire. Piling, stacking or storing oil-affected items can prevent heat from
escaping and so create a fire hazard.
• If it is unavoidable that fabrics that contain vegetable or cooking oil or have been conta-
minated by hair care products be placed in a tumble dryer they should first be washed
in hot water with extra detergent – this will reduce, but not eliminate, the hazard.
• Maximum mass of dry cloth: 10.6 kg.
• A-weighted emission sound pressure level at working stations: <70 dB(A).

Installation manual 7
1.1 Gas heated tumble dryer:
• Before installation, check that the local distribution conditions, nature of gas and pres-
sure and the adjustment of the appliance are compatible.
• The machine is not to be installed in rooms containing cleaning machines with per-
chloroethylene, TRICHLOROETHYLENE or CHLOROFLUOROCONTAINING HY-
DROCARBONS as cleaning agents.
• If you can smell gas:
– Do not switch on any equipment
– Do not use electrical switches
– Do not use telephones in the building
– Evacuate the room, building or area
– Contact the person responsible for the machine
• Additional requirements for the following countries; AT, BE, BG, HR, CY, CZ, DK, EE,
FI, FR, DE, GR, HU, IS, IE, IT, LV, LT, LU, MT, NL, NO, PL, PT, RO, SK, SI, ES, SE, CH,
TR, UK:
– The appliance can be used in public areas.
– This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and knowl-
edge if they have been given supervision or instruction concerning use of the appliance
in a safe way and understand the hazards involved. Children shall not play with the ap-
pliance. Cleaning and user maintenance shall not be made by children without
supervision.
• Additional requirements for other countries:
– This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety. Children should be supervised to ensure that they
do not play with the appliance.
1.2 General safety information
In order to prevent damage to the electronics (and other parts) that may occur as the result of condensation, the ma-
chine should be placed in room temperature for 24 hours before being used for the first time.
1.3 Commercial use only
The machine/machines covered by this manual is/are made for commercial and industrial use only.
1.4 Copyright
This manual is intended solely for consultation by the operator and can only be given to third parties with the permis-
sion of Electrolux Professional company.

8Installation manual
1.5 Symbols
Caution
Caution, hot surface
Caution, high voltage
Read the instructions before using the machine

Installation manual 9
2 Warranty terms and exclusions
If the purchase of this product includes warranty coverage, warranty is provided in line with local regulations and sub-
ject to the product being installed and used for the purposes as designed, and as described within the appropriate
equipment documentation.
Warranty will be applicable where the customer has used only genuine spare parts and has performed maintenance
in accordance with Electrolux Professional user and maintenance documentation made available in paper or elec-
tronic format.
Electrolux Professional strongly recommends using Electrolux Professional approved cleaning, rinse and descaling
agents to obtain optimal results and maintain product efficiency over time.
The Electrolux Professional warranty does not cover:
• service trips cost to deliver and pick up the product;
• installation;
• training on how to use/operate;
• replacement (and/or supply) of wear and tear parts unless resulting from defects in materials or workmanship re-
ported within one (1) week from the failure;
• correction of external wiring;
• correction of unauthorized repairs as well as any damages, failures and inefficiencies caused by and/or resulting
from;
– insufficient and/or abnormal capacity of the electrical systems (current/voltage/frequency, including spikes and/
or outages);
– inadequate or interrupted water supply, steam, air, gas (including impurities and/or other that does not comply
with the technical requirements for each appliance);
– plumbing parts, components or consumable cleaning products that are not approved by the manufacturer;
– customer’s negligence, misuse, abuse and/or non-compliance with the use and care instructions detailed within
the appropriate equipment documentation;
– improper or poor: installation, repair, maintenance (including tampering, modifications and repairs carried out
by third parties not authorized third parties) and modification of safety systems;
– Use of non-original components (e.g.: consumables, wear and tear, or spare parts);
– environment conditions provoking thermal (e.g. overheating/freezing) or chemical (e.g. corrosion/oxidation)
stress;
– foreign objects placed in- or connected to- the product;
– accidents or force majeure;
– transportation and handling, including scratches, dents, chips, and/or other damage to the finish of the product,
unless such damage results from defects in materials or workmanship and is reported within one (1) week of deliv-
ery unless otherwise agreed;
• product with original serial numbers that have been removed, altered or cannot be readily determined;
• replacement of light bulbs, filters or any consumable parts;
• any accessories and software not approved or specified by Electrolux Professional.
Warranty does not include scheduled maintenance activities (including the parts required for it) or the supply of
cleaning agents unless specifically covered within any local agreement, subject to local terms and conditions.
Check on Electrolux Professional website the list of authorized customer care.

10 Installation manual
3 Technical data
3.1 Drawing
C
A
1
2
D
B
B(a)
B(c)
3
E
F
G
H
4
5
J
I
B(b)
fig.W00896A
1 Operating panel
2 Door opening, ⌀400 mm
3 Electrical connection
4 Gas connection
5 Exhaust connection
A B B(a) B(b) B(c) C
mm 720 805 765 750 695 1115
D E F G
mm 405 45 180 90
H I J
mm 115 80 560

Installation manual 11
3.2 Technical data
Weight, net kg 99
Drum volume litres 190
Drum diameter mm 680
Drum depth mm 555
Drum speed rpm 47
Rated capacity, filling factor 1:18 (Max. load) kg 10.6
Rated capacity, filling factor 1:22 (Recommended. load) kg 8.6
Heating: Electricity kW 6
kW 8
Heating: Gas kW 6
kW 8
Air consumption, Electric heating, 6 kW m3/h 270
Air consumption, Electric heating, 8 kW m3/h 290
Air consumption, Gas heating, 6 kW m3/h 270
Air consumption, Gas heating, 8 kW m3/h 290
Pressure drop, Electric heating, 6 kW Max. Pa 380
Pressure drop, Electric heating, 8 kW Max. Pa 350
Pressure drop, Gas heating, 6 kW Max. Pa 380
Pressure drop, Gas heating, 8 kW Max. Pa 350
A-weighted emission sound pressure level at working stations dB(A) <70
Heat emission of installed power, max % 15
3.3 Connections
Air outlet ⌀mm 125
Gas connection 1/2” ISO 7/1–R1/2

12 Installation manual
3.4 Machines with heat pump
3.4.1 Drawing
A
1
2
C
B
D
E
3
F
4
5
G
I
H
K
J
L
M
N
O
6
fig.8005A
1 Operating panel
2 Door opening, ⌀400 mm
3 Electrical connection
4 Drain (condensed water)
5Drain (cooling water)
6 Water connection
A B C D E F
mm 720 775 1685 1410 1505 45
G H I J K L
mm 110 90 50 95 340 720
M N O
mm 775 690 610

Installation manual 13
3.4.2 Technical data
Weight, net kg 188
Drum volume litres 190
Drum diameter mm 680
Drum depth mm 555
Drum speed, medium load rpm 47
Rated capacity, filling factor 1:18 (Max. load) kg 10.6
Rated capacity, filling factor 1:22 (Max. recommended load) kg 8.6
Sound power/pressure level at drying* dB(A) 71/56
Average heat emission per drying cycle used to assess ventilation need** kW 1.0
* Sound power levels measured according to ISO 60704.
** For assistance with dimensioning necessary ventilation needs, contact authorized ventilation technician. For suffi-
cient ventilation all sources introducing heat need to be taken into account plus all other parameters effecting the
ventilation need. Climate zone, building parameters, room size, etc.
Heat pump
Weight, net kg 52
Pipe connection, condensed water ⌀mm 19
Pipe connection, drain ⌀mm 20
Water connection 3/4”
Type of refrigerant R134a
Amount of refrigerant kg 1.35
Fluorinated greenhouse gases
This product contains fluorinated greenhouse gases:
R134A: 1.350 kg
GWP 1430
CO2equivalent 1.931 t
Hermetically sealed

14 Installation manual
4 Setup
4.1 Unpacking
Cut and remove the two plastic straps between the machine and pallet. There is one strap on each side of the
machine.
fig.7676
Remove the machine from the pallet.
Note!
When moving the machine, handle it with care. The drum has no transport clamps.
Place the machine on its final position.
4.1.1 Machines with heat pump
Note!
Two persons are recommended for the unpacking.
The heat pump unit and the tumble dryer are delivered as one unit.
The machine is delivered complete with supporting feet.
The machine is delivered bolted onto the transport pallet and packed in a crate or box.
Remove packing from the machine.
Remove the screws and the two brackets between the machine and pallet.
fig.W00599
Remove the machine from the pallet.
Note!
When moving the machine, handle it with care. The drum has no transport clamps.
The heat pump unit must only be put down on the feet. It may be tilted a bit on the sides but not completely
tipped over. This will damage the heat pump.
Place the machine on its final position.

Installation manual 15
4.2 Recycling instruction for packaging
4
56
3
1
2
fig.X02405
Fig. Description Code Type
1 Wrapping film LDPE 4 Plastics
2 Corner protection PS 6 Plastics
3 Cardboard packaging PAP 20 Paper
4 Pallet FOR 50 Wood
5Cable Tie Nylon
6 Plastic bag PET 1 Plastics

16 Installation manual
4.3 Siting
The figure shows recommended distance to walls and/or other machines.
A A
B
fig.X00959
A 5–500 mm (Min. 5 mm)
B 500 mm (Min. 200 mm)
Note!
The machine should be positioned so that there will be enough space for working, both for the user and
service personnel.
Respecting the given recommendations will provide easy access for maintenance and service operations.
In case of space limitations, it is possible to install machines without respecting to the given recommendations. If so,
keep in mind that it might be necessary to disconnect and move other machines to be able to reach and perform
service on affected machine.

Installation manual 17
4.4 Drain connection (only for machines with heat pump)
Connect the drain to the heat pump unit.
Note!
The outlet condense water (4) and the cooling water (5) must be connected to separate outlets.
The hose (4) must be positioned over the water level in the floor drain.
Note!
The drain must be lower than the drain outlet from the heat pump unit. If not the water will flow back into the
machine. Adjust with the feet.
The hoses shall hang in gentle arcs.
4
5
fig.W00609
4.5 Water connection (only for machines with heat pump)
All water intake connections to the machine should be fitted with manual shut-off valves and filters, to facilitate instal-
lation and servicing.
Water pipes and hoses should be flushed clean before installation.
The machine shall be connected with new water hoses. Re-used water hoses must not be used.
Hoses are to be of an approved type and grade and comply with IEC 61770.
After installation hoses must hang in gentle arcs.
All connectors present on the machine must be connected.
Connect the water to the water cooling system (6).
6
W00609A
Water pressure:
Miniumum: 50 kPa (0.5 kp/cm2)
Maximum: 800 kPa (8 kp/cm2)
Recommended: 200–600 kPa (2–6 kp/cm2)
Note!
If the water pressure is below the minimum value, the drying result can not be guaranteed for certain
program.

18 Installation manual
4.6 Mechanical installation
Level the machine with the feet of the machine. The maximum height adjustment of the feet is 50 mm.
If the machine is mounted on a base it needs to be fastened to the base.
fig.6321

Installation manual 19
5 Marine installation
To ensure steadiness of the machine it is important to fasten the machine to the foundation.
Fasten four fittings to the foundation using four x M10 set screws.
Note!
The four fittings are not supplied with the machine and must be ordered as kit No. 487193544.
Fasten the machine to the fittings.
675 mm / 26 9/16 inch
M10 M10
M10
M10
600 mm / 23 5/8 inch 400 mm / 15 3/4 inch
M10
20Nm
512 mm / 20 5/32 inch
585 mm / 23 1/32 inch
fig.6322
Note!
Marine installation is not applicable for gas heated machines.

20 Installation manual
6 Evacuation system
6.1 Air principle
The fan creates low pressure in the machine, drawing air into the drum via the heating unit.
The heated air passes through the garments and the drum vents.
The air then flows out through a lint filter positioned in the door. After this, the air is evacuated through the fan and ex-
haust system.
Note!
It is very important that the machine gets enough fresh air in order to get the best drying result.
6.1.1 For machines with heat pump
Ventilating the room
When the machine is in operation, the room temperature increases. Due to this, the room must have sufficient
ventilation.
All sources introducing heat into the same room requires to be considered when dimensioning the ventilation. Heat
sources could for example be: more tumble dryers, drying cabinets, washers, ironers, radiators, etc. The combination
of several sources for heat introduction leads to an increased need for ventilation flow. Other factors may also influ-
ence the needed ventilation flow, such as climate zone, building parameters, room size, etc. For assistance with di-
mensioning necessary ventilation needs, contact authorized ventilation technician.
6.2 Fresh air
For maximum efficiency and the shortest possible drying time, it is important to ensure that fresh air is able to enter
the room from the outside in the same volume as that is blown out of the room.
To avoid draught in the room it is important to place the air inlet behind the machine.
The area of the air inlet opening is recommended to be five times the size of the exhaust pipe area. The area of the
inlet opening is the area through which the air can flow without resistance from the grating/slatted cover.
5 x A
A
fig.6312
Note!
Gratings/slatted covers often block half of the total fresh air vent area. Remember to take this into account.