Electrolux Professional DC6-10HP User manual

Installation manual
Drying Cabinet
DC6-10HP
Original instructions
427001232/EN
2022.03.01

Contents
Contents
1 Safety Precautions ..............................................................................................................................5
1.1 General safety information..........................................................................................................5
1.2 Symbols....................................................................................................................................5
2 Technical data.....................................................................................................................................6
2.1 Dimensions drawing...................................................................................................................6
2.2 Technical data ...........................................................................................................................7
3 Master and Slave heat pumps ..............................................................................................................8
4 Unpacking ..........................................................................................................................................9
4.1 Installation kit ............................................................................................................................9
5 Weight reduction to facilitate installation .............................................................................................. 10
5.1 Remove the hanger section ......................................................................................................10
5.2 Remove the doors.................................................................................................................... 11
5.3 Remove the dehumidifier units..................................................................................................13
6 Positioning/Attachment ......................................................................................................................16
6.1 Ventilate the room....................................................................................................................16
6.2 Horizontal adjustment ..............................................................................................................16
6.3 Attachment to the wall ..............................................................................................................17
7 Connection to floor drain ....................................................................................................................18
8 Electrical connection..........................................................................................................................19
8.1 Alternative electrical connection................................................................................................19
8.2 Connection to reservation system .............................................................................................20
9 Function check..................................................................................................................................21
10 Disposal information..........................................................................................................................22
10.1 Disposal of appliance at end of life ............................................................................................22
10.2 Disposal of packing..................................................................................................................22
The manufacturer reserves the right to make changes to design and component specifications.

Installation manual 5
1 Safety Precautions
This appliance can be used in public areas.
Remove all objects from pockets such as lighters and matches.
WARNING. This appliance is intended only for drying textiles washed in water.
DO NOT MODIFY THIS APPLIANCE.
Servicing shall be carried out only by authorized personnel.
Only authorized spare parts shall be used.
When performing service or replacing parts, the power must be disconnected.
A-weighted emission sound pressure level at workstations: <70 dB
Additional requirements for the following countries: AT, BE, BG, HR, CY, CZ, DK, EE, FI,
FR, DE, GR, HU, IS, IE, IT, LV, LT, LU, MT, NL, NO, PL, PT, RO, SK, SI, ES, SE, CH, TR,
UK:
• This appliance can be used in public areas.
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory
or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction con-
cerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the
appliance. Cleaning and user maintenance shall not be made by children without supervision.
Additional requirements for other countries:
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental ca-
pabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do
not play with the appliance.
1.1 General safety information
Do not hose down the machine with water.
In order to prevent damage to the electronics (and other parts) that may occur as the result of condensation, the ma-
chine should be placed in room temperature for 24 hours before being used for the first time.
1.2 Symbols
Caution
Caution, hot surface
Read the instructions before using the machine.
Be careful. The drying cabinet is top heavy and can tip over easily.

6Installation manual
2 Technical data
2.1 Dimensions drawing
G
H
I
J
A
F
B
E
C D
K
1
3
2
fig.W01395
A B C D E F G H I J K
mm 1395 652 1917 1931 14 1078 496 468 621 970 850
1 Control panel
2 Condensation nipple ⌀10 mm, hose 3 m included
3 Connecting cable 2.5 m included

Installation manual 7
2.2 Technical data
Capacity: kg of laundry 10
Drainage capacity: g/min* 55
Electrical connection: 220-240V 1 AC
50-60 Hz
Traditional threaded fuse: A 13A
Automatic fuse: A 13A
Power: kW 2.6
Hanging length: meters 20
Weight: kg 205
Sound pressure level: A-weighted emission sound pressure level
dB (A)
<57
Average heat emission per drying cycle used
to assess ventilation need**:
kW 1.1
* 6.5 kg dry weight cotton, 50% residual moisture.
** For assistance with dimensioning necessary ventilation needs, contact authorized ventilation technician. For suffi-
cient ventilation all sources introducing heat need to be taken into account plus all other parameters effecting the
ventilation need. Climate zone, building parameters, room size, etc.
Connections
Connection, condensation Plastic hose dim ⌀10 mm. 3 m hose included.
Heat pump
Type of refrigerant R407C
Amount of refrigerant kg 1.0
Fluorinated greenhouse gases
This product contains fluorinated greenhouse gases.
GWP: 1430
CO2equivalent: 1.43 t
Leak test: 28 bar
Hermetically sealed.
Energy consumption and drying times
Drying of centrifuged laundry **)
Programs: Normal drying
Energy consumption: kWh / kg of laundry 0.31
Energy dried water: kWh / liter 0.62
Drying time ***): minutes 60
**) The values may vary depending on:
• speed during spin cycle
• temperature, humidity in the room
• air circulation in the room (supply air, exhaust air)
• settings in the parameter list regarding moisture sensor and time for the SUN program
The values relate to a 6 kg load with 50% residual moisture.
***) The drying cabinet reconditions 5 minutes after the textiles have dried

8Installation manual
3 Master and Slave heat pumps
1
2
fig.W01396
1MASTER
2SLAVE
The drying cabinet contains two heat pumps, a MASTER and a SLAVE.
The heat pump on the left is the MASTER and the one on the right is the SLAVE.
As the name implies, the MASTER controls the process, while the SLAVE follows. If the SLAVE becomes inoperable,
the drying cabinet will still be able to work, but at reduced power. However, if the MASTER were to stop working, the
drying cabinet will stop. In such case, it is possible to continue the process by reconfiguring the SLAVE to temporarily
make it the MASTER. This is described in more detail in the Service Manual.
It is not normally possible to perform heat pump servicing in the field. If servicing is required, the complete units must
be removed and sent to Nimo-Verken AB, which has an exchange system for complete units.
The electrical connection is found on the connection panel of each unit. The panels face each other and are depicted
in the figure below.
3 4
fig.W01397
3MASTER, left
4SLAVE, right

Installation manual 9
4 Unpacking
Removal all packing materials. Do not use sharp objects, as this could damage the product.
Packaging materials such as plastic and styrofoam should be kept out of reach of children.
4.1 Installation kit
1
2
3
4
5
6
fig.W01398
1 Screw T6S 6x75 galvanized for wall mounting
2 Screw M6S 8x16 for mounting bracket
3 Washer BRB 8.4x17x1.6
4 Wall plug
5Mounting bracket for wall mounting
6 Brush for filter cleaning

10 Installation manual
5 Weight reduction to facilitate installation
The following can be done to reduce the weight of the drying cabinet and thereby facilitate installation.
If all of the measures are implemented, the weight of the drying cabinet will be cut almost in half.
•Remove the hanger section
•Remove the doors
•Remove the dehumidifier units
5.1 Remove the hanger section
• Remove the hanger stop as illustrated.
• Lift and unhook the section.
fig.W01399

Installation manual 11
5.2 Remove the doors
Right door
• Undo the four fastening screws securing the hatch (A) and remove the hatch.
• Remove the cover (B) from over the upper hinge and expose the door cable (C). Then detach the cable from the
connector (D).
• Remove the upper hinge (E), which is secured with two screws. Carefully pull the hinge loose from the cable.
The hinge has a slot where the cable can be threaded in or out.
• Lift the door off of the drying cabinet.
E
A
E
CD
B
fig.W01400
A Hatch
B Cover over the hinge
C Door cable
D Connector
E Upper hinge

12 Installation manual
Left door
• Remove the cover (F) from over the hinge.
• Remove the hinge (G), which is secured with two screws.
• Lift the door off of the drying cabinet.
F
G
fig.W01401
F Cover over the hinge
G Upper hinge

Installation manual 13
5.3 Remove the dehumidifier units
• Detach the front plate (A), which is secured with two screws on the top under plastic plugs. Unplug the electrical
connection between the door switches and the left dehumidifier unit. Then remove the front plate.
• Detach the filters (B) and remove them.
A
B
fig.W01402
A Front plate
B Dirt filter

14 Installation manual
• Remove the hatch (C), which is secured with three screws at the bottom edge of the hatch. Do this on both the left
and the right side.
• Remove the air deflector (D). This is secured with two plastic Torx 40 screws, which are located under cover plugs
(E). The air deflector can either be taken out or left in position.
Do not forget to reinstall the cover plugs when reassembling the cabinet. Otherwise, there will be air leakage, resulting in reduced performance.
C
D
E
fig.W01403
C Hatch
D Air deflector
E Cover plugs

Installation manual 15
• Detach the electrical cables as illustrated.
B
S
U
D
2
3
1
4
5
78
6
6
fig.W01404
1 Property’s reservation system
2 Loose modular cable, black
3 User interface (control panel), white cable
4 LED lighting
5 Door switch
6 Mains connection
7MASTER
8SLAVE
• Detach the condensation connection (F) from both units.
• Remove the locking washer (G) and take out both of the dehumidifier units.
F
G
fig.W01405

16 Installation manual
6 Positioning/Attachment
The drying cabinet is only intended for placement indoors in a dry place
The drying cabinet may not be placed in an environment where high-pressure water is used for cleaning
6.1 Ventilate the room
When the machine is in operation, the room temperature increases. Due to this, the room must have sufficient
ventilation.
All sources introducing heat into the same room requires to be considered when dimensioning the ventilation. Heat
sources could for example be: more tumble dryers, drying cabinets, washers, ironers, radiators, etc. The combination
of several sources for heat introduction leads to an increased need for ventilation flow. Other factors may also influ-
ence the needed ventilation flow, such as climate zone, building parameters, room size, etc. For assistance with di-
mensioning necessary ventilation needs, contact authorized ventilation technician.
6.2 Horizontal adjustment
The drying cabinet must stand level on a flat surface, resting on all four feet.
Adjust the feet from the outside using a hex key. Check that the top edge of the doors match and are aligned.
The adjustable feet have hexagonal grips, size 17.
fig.W01406

Installation manual 17
6.3 Attachment to the wall
The cabinet must be attached to the wall to prevent tipping.
The installation kit contains two angle brackets that are mounted on the upper part of the drying cabinet as illustrated.
Use the provided screws. The brackets have grooves for adjustment to the wall.
Secure the cabinet to the wall. The installation kit contains a fastening screw and plastic plugs.
fig.W01407

18 Installation manual
7 Connection to floor drain
The drying cabinet comes with a preinstalled hose for connection to a floor drain. The hose connection if found on
both sides at the lower rear corner of the cabinet.
fig.W01408
• Connect a new drain hose to one of the cabinet connections and route it to the drain.
• If the floor drain is higher than the cabinet drain, make sure that the hose makes an arch down towards the floor
and forms a water trap. If you fail to do this, there is a risk of condensation flowing back to the box when the pump
is not running. This could cause the box to fill with water and the cabinet to stop working.
21
3
fig.W01409
1 Left side's drain hose
2 Right side's drain hose
3 Nipple
• Replace/check the drain side by moving the nipple drain hose on either the right or the left side.
The hoses from the dehumidifier units are delivered from the factory connected to the drain on the left side.
The hose must not under any circumstances be bent so much that the flow of water is obstructed

Installation manual 19
8 Electrical connection
The electrical installation may only be performed by qualified personnel.
The drying cabinet is delivered ready for connection, with cable and grounded plug.
Heating options Mains voltage Hz Total output
kW
Recommended fuse
A
Heat pump 230V 1~ 50 2.6 13
fig.W01410
We recommend that the mains cable be equipped with a ground fault interrupter.
The electrical outlet must be in a location that makes it easy to unplug the cabinet if necessary.
Connecting to an external payment system
Connect the cables from the external payment system to terminal block positions 1 and 2 "EXT SW".
Activate the connection to the external payment system as follows:
Press and hold the Stop button, and then press both program buttons.
ACCESS 0000 is shown in the display.
Enter the code 9191.
Enter the numbers using the program buttons; press Stop.
Use the program buttons to move to Parameter 117, and enter the parameter using the Stop button.
Set the parameter value to 1. This will activate the cabinet for network use. Use the Stop button to exit the parameter.
To confirm the new settings: Press the Stop button and then Butterfly.
Restore factory settings
To restore the electronics to factory settings:
Press the Stop button, and then press both program buttons. The display shows FACT DEFS.
8.1 Alternative electrical connection
The drying cabinet can also be permanently connected. In such case, it must be connected via an all-pole switch in-
stalled in the immediate vicinity of the drying cabinet.
The grounded electrical outlet or all-pole switch must be within easy reach of the drying cabinet after it has been
installed.

20 Installation manual
8.2 Connection to reservation system
If the property has a reservation system for the laundry room, the drying cabinet can be connected to this.
Connection is handled via an external electronics box that can be ordered from Electrolux Professional. This is con-
nected to connector B on the Master unit.
12
B
fig.W01411
B Master unit connector
1MASTER
2SLAVE