Electrolux Professional TD6 14LAC User manual

Installation manual
Tumble dryer
TD6–14LAC
Type N2...
Original instructions
438905930/GB, IE
2023.12.18

Contents
Contents
1 Safety Precautions ..............................................................................................................................5
1.1 Additional safety precautions for gas heated tumble dryer .............................................................7
1.2 General information ...................................................................................................................7
1.3 Commercial use only..................................................................................................................7
1.4 Copyright ..................................................................................................................................7
1.5 Ergonomics certification .............................................................................................................7
1.6 Symbols....................................................................................................................................8
2 Warranty terms and exclusions.............................................................................................................9
3 Technical data...................................................................................................................................10
3.1 Electric heated machines..........................................................................................................10
3.1.1 Drawing.........................................................................................................................10
3.1.2 Technical data................................................................................................................ 11
3.2 Steam heated machines...........................................................................................................12
3.2.1 Drawing.........................................................................................................................12
3.2.2 Technical data................................................................................................................13
3.3 Gas heated machines ..............................................................................................................14
3.3.1 Drawing.........................................................................................................................14
3.3.2 Technical data................................................................................................................15
4 Setup ...............................................................................................................................................16
4.1 General...................................................................................................................................16
4.2 Unpacking...............................................................................................................................16
4.3 Recycling instruction for packaging ...........................................................................................18
4.4 Wheels ...................................................................................................................................19
4.5 Siting ......................................................................................................................................19
4.6 Mechanical installation .............................................................................................................20
5 Evacuation system ............................................................................................................................21
5.1 Air principle .............................................................................................................................21
5.1.1 Electric-, Steam- and Gas heated machines .....................................................................21
5.1.2 Machines with heat pump................................................................................................21
5.2 Fresh air..................................................................................................................................22
5.3 Exhaust duct ...........................................................................................................................22
5.4 Shared exhaust duct ................................................................................................................23
5.5 Exhaust dimensioning ..............................................................................................................23
5.6 Adjusting the air flow (not valid for tumble dryers with heat pump)................................................24
6 Electrical connection..........................................................................................................................30
6.1 Electrical installation ................................................................................................................30
6.2 Machine connection with ferrite.................................................................................................31
6.2.1 Machines with AFC or DSC.............................................................................................31
6.3 Single-phase connection ..........................................................................................................32
6.4 Three-phase connection...........................................................................................................33
6.5 Electrical connections ..............................................................................................................34
7 Steam connection .............................................................................................................................35
7.1 Connecting the steam ..............................................................................................................35
8 Gas connection .................................................................................................................................36
8.1 Fasten the label .......................................................................................................................36
8.2 General...................................................................................................................................36
8.3 Gas installation........................................................................................................................37
8.4 Table of pressure and adjustment..............................................................................................37
8.5 Test run...................................................................................................................................38
8.6 Converting instructions.............................................................................................................40
8.7 Data label................................................................................................................................42
9 Reversing the door ............................................................................................................................43
10 At first power up ................................................................................................................................48
10.1 Select language.......................................................................................................................48
10.2 Set time and date.....................................................................................................................48
10.3 Activate/Deactivate the service alarm ........................................................................................48
11 Function check..................................................................................................................................49
12 Disposal information..........................................................................................................................52
12.1 Disposal of appliance at end of life ............................................................................................52
12.2 Disposal of packing..................................................................................................................52

Contents
The manufacturer reserves the right to make changes to design and component specifications.

Installation manual 5
1 Safety Precautions
• Servicing shall be carried out only by authorized personnel.
• Only authorized spare parts, accessories and consumables shall be used.
• The machine is not to be used if industrial chemicals have been used for cleaning.
• Do not dry unwashed items in the machine.
• Items that have been soiled with substances such as cooking oil, acetone, alcohol, pet-
rol, kerosene, spot removers, turpentine, waxes and wax removers should be washed
in hot water with an extra amount of detergent before being dried in the machine.
• Items such as foam rubber (latex foam), shower caps, waterproof textiles, rubber
backed articles and clothes or pillows fitted with foam rubber pads should not be dried
in the machine.
• Fabric softeners or similar products should be used as specified by the fabric softener
instructions.
• The final part of a drying cycle occurs without heat (cool down cycle) to ensure that the
items are left at a temperature that ensures that the items will not be damaged.
• Remove all objects from pockets such as lighters and matches.
• WARNING. Never stop the machine before the end of the drying cycle unless all items
are quickly removed and spread out so that the heat is dissipated.
• Adequate ventilation has to be provided to avoid the back flow of gases into the room
for appliances burning other fuels, including open fires.
• Exhaust air must not be discharged into a flue which is used for exhausting fumes from
appliances burning gas or other fuels.
• The machine must not be installed behind a lockable door, a sliding door or a door with
a hinge on the opposite side to that of the machine in such a way that a full opening of
the machine is restricted.
• If the machine has a lint trap this has to be cleaned frequently.
• The lint must not be accumulated around the machine.
• DO NOT MODIFY THIS APPLIANCE.
• When performing service or replacing parts, the power must be disconnected.
• When the power is disconnected, the operator must see that the machine is discon-
nected (that the plug is removed and remains removed) from any point to which he has
access. If this is not possible, due to the construction or installation of the machine, a
disconnection with a locking system in the isolated position shall be provided.
• In accordance with the wiring rules: mount a multi-pole switch prior to the machine to
facilitate installation and service operations.
• Stationary appliances not fitted with means for disconnection from the supply mains
having a contact separation in all poles that provide full disconnection under overvolt-
age category III, means for disconnection must be incorporated in the fixed wiring in
accordance with the wiring rules.
• WARNING: The appliance must not be supplied through an external switching device,
such as a timer, or connected to a circuit that is regularly switched on and off by a utility.
• If different rated voltages or different rated frequencies (separated by a /) are stated at
the machine data plate, instructions for adjusting the appliance for operation at the re-
quired rated voltage or rated frequency are stated in the installation manual.
• The openings in the base, shall not be obstructed by a carpet.

6Installation manual
• Oil-affected items can ignite spontaneously, especially when exposed to heat sources
such as in a tumble dryer. The items become warm, causing an oxidation reaction in
the oil. Oxidation creates heat. If the heat cannot escape, the items can become hot
enough to catch fire. Piling, stacking or storing oil-affected items can prevent heat from
escaping and so create a fire hazard.
• If it is unavoidable that fabrics that contain vegetable or cooking oil or have been conta-
minated by hair care products be placed in a tumble dryer they should first be washed
in hot water with extra detergent – this will reduce, but not eliminate, the hazard.
• Maximum mass of dry cloth: 14.2 kg.
• A-weighted emission sound pressure level at working stations: 70 dB(A).
• Additional requirements for the following countries; AT, BE, BG, HR, CY, CZ, DK, EE,
FI, FR, DE, GR, HU, IS, IE, IT, LV, LT, LU, MT, NL, NO, PL, PT, RO, SK, SI, ES, SE, CH,
TR, UK:
– The appliance can be used in public areas.
– This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved. Children shall not
play with the appliance. Cleaning and user maintenance shall not be made by chil-
dren without supervision.
• Additional requirements for other countries:
– This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, un-
less they have been given supervision or instruction concerning use of the appliance
by a person responsible for their safety. Children should be supervised to ensure
that they do not play with the appliance.

Installation manual 7
1.1 Additional safety precautions for gas heated tumble dryer
• Before installation, check that the local distribution conditions, nature of gas and pres-
sure and the adjustment of the appliance are compatible.
• The machine is not to be installed in rooms containing cleaning machines with per-
chloroethylene, TRICHLOROETHYLENE or CHLOROFLUOROCONTAINING HY-
DROCARBONS as cleaning agents.
• NOTE: it is pointed out that the connection and commissioning of appliances complying
with this standard are subject to observance of the installation regulations in force in
the countries where these appliances are marketed.
• Connection to the appliance shall be made with a flexible hose suitable for the appli-
ance category in accordance with national installation regulations of the country of des-
tination and that in case of doubt the installer shall contact the supplier.
• The appliance should be installed on non-flammable materials for the floor, worktop
and/or wall close to the appliance if required.
• If you can smell gas:
– Do not switch on any equipment
– Do not use electrical switches
– Do not use telephones in the building
– Evacuate the room, building or area
– Contact the person responsible for the machine
1.2 General information
Conditions for storage and transportation of the appliance should fulfil a temperature between -20℃/ + 70℃and
max Humidity of 95% RH.
In order to prevent damage to the electronics (and other parts) that may occur as the result of condensation, the ma-
chine should be placed in room temperature for 24 hours before being used for the first time.
Electric power supply should follow:
• Max range for each country rated voltage: -15% / +10%.
• Max range for each country rated frequency: ± 3 Hz.
• Dips/Interruption: 5 Dips/day (100% voltage lost, with 3-4 minutes duration).
A stable power supply is always the best. Fluctuations gives stress and additional load on all electric and electronic
components.
1.3 Commercial use only
The machine/machines covered by this manual is/are made for commercial and industrial use only.
1.4 Copyright
This manual is intended solely for consultation by the operator and can only be given to third parties with the permis-
sion of Electrolux Professional AB company.
1.5 Ergonomics certification
The human body is designed for movement and activity but physical stress injuries as a result of static and repetitive
movements or unfavorable working postures may occur.
The ergonomic features of your product, the ones which may influence your physical and cognitive interaction with it,
have been assessed and certified.
A product which exhibits ergonomic features, in fact, shall fulfil specific ergonomic requirements, belonging to three
different areas: Polytechnic, Biomedical and Psychosocial (usability and satisfaction).
For each of these areas, specific tests with real users have been performed. The product was therefore compliant
with the ergonomic acceptability criteria requested by the standards.

8Installation manual
In case several machines are managed by the same operator the repetitive movements will increase and as a conse-
quence of this the related biomechanical risk will increase exponentially.
The possible postural risks are the interaction with the user interface, display and buttons.
Follow the below recommendations to avoid, as much as possible, operators acquiring bodily injury.
• Make sure there are suitable trolleys or baskets for loading, unloading and transportation.
• Organize job rotation in the working place in the case several machines are managed by the same operator.
1.6 Symbols
Caution
Caution, hot surface
Caution, high voltage
Warning, risk of fire / flammable material
Danger, crush hazard
Read the instructions before using the machine

Installation manual 9
2 Warranty terms and exclusions
If the purchase of this product includes warranty coverage, warranty is provided in line with local regulations and sub-
ject to the product being installed and used for the purposes as designed, and as described within the appropriate
equipment documentation.
Warranty will be applicable where the customer has used only genuine spare parts and has performed maintenance
in accordance with Electrolux Professional user and maintenance documentation made available in paper or elec-
tronic format.
Electrolux Professional strongly recommends using Electrolux Professional approved cleaning, rinse and descaling
agents to obtain optimal results and maintain product efficiency over time.
The Electrolux Professional warranty does not cover:
• service trips cost to deliver and pick up the product;
• installation;
• training on how to use/operate;
• replacement (and/or supply) of wear and tear parts unless resulting from defects in materials or workmanship re-
ported within one (1) week from the failure;
• correction of external wiring;
• correction of unauthorized repairs as well as any damages, failures and inefficiencies caused by and/or resulting
from;
– insufficient and/or abnormal capacity of the electrical systems (current/voltage/frequency, including spikes and/
or outages);
– inadequate or interrupted water supply, steam, air, gas (including impurities and/or other that does not comply
with the technical requirements for each appliance);
– plumbing parts, components or consumable cleaning products that are not approved by the manufacturer;
– customer’s negligence, misuse, abuse and/or non-compliance with the use and care instructions detailed within
the appropriate equipment documentation;
– improper or poor: installation, repair, maintenance (including tampering, modifications and repairs carried out
by third parties not authorized third parties) and modification of safety systems;
– Use of non-original components (e.g.: consumables, wear and tear, or spare parts);
– environment conditions provoking thermal (e.g. overheating/freezing) or chemical (e.g. corrosion/oxidation)
stress;
– foreign objects placed in- or connected to- the product;
– accidents or force majeure;
– transportation and handling, including scratches, dents, chips, and/or other damage to the finish of the product,
unless such damage results from defects in materials or workmanship and is reported within one (1) week of
delivery unless otherwise agreed;
• product with original serial numbers that have been removed, altered or cannot be readily determined;
• replacement of light bulbs, filters or any consumable parts;
• any accessories and software not approved or specified by Electrolux Professional.
Warranty does not include scheduled maintenance activities (including the parts required for it) or the supply of
cleaning agents unless specifically covered within any local agreement, subject to local terms and conditions.
Check on Electrolux Professional website the list of authorized customer care.

10 Installation manual
3 Technical data
3.1 Electric heated machines
3.1.1 Drawing
1
2
A
C
BD
E
F
G
H
3
I
J
4
fig.X00718
1 Operating panel
2 Door opening, ⌀580 mm
3 Electrical connection
4 Exhaust connection
A B C D E F
mm 795 965 1770 775 835 750
G H I J
mm 110 270 240 175

Installation manual 11
3.1.2 Technical data
Weight, net kg 202
Drum volume liters 255
Drum diameter mm 755
Drum depth mm 595
Drum speed, medium load rpm 43
Rated capacity, filling factor 1:18 (Max. load) kg 14.2
Rated capacity, filling factor 1:22 (Recommended load) kg 11.6
Heating: Electricity kW 6.0
kW 9.0
kW 13.2
kW 13.5
Optimum air flow, 6.0 kW** m3/h 250
Optimum air flow, 9.0 kW** m3/h 250
Optimum air flow, 13.5 kW** m3/h 460
Optimum static back pressure, 6.0 kW** Pa 710
Maximum static back pressure, 6.0 kW** Pa 715
Optimum static back pressure, 9.0 kW** Pa 710
Maximum static back pressure, 9.0 kW** Pa 715
Optimum static back pressure, 13.5 kW** Pa 550
Maximum static back pressure, 13.5 kW** Pa 570
Sound power/pressure level at drying* dB(A) 72/56
Heat emission of installed power, max % 15
* Sound power levels measured according to ISO 60704.
** In a cold empty machine.
Connections
Air outlet ⌀mm 200

12 Installation manual
3.2 Steam heated machines
3.2.1 Drawing
1
2
A
C
B(a) D
E
F
4
B(b)
G
3
H
I
5
J
K
6
L
fig.X00720
1 Operating panel
2 Door opening, ⌀580 mm
3 Electrical connection
4 Steam connection
5Condensate connection
6 Exhaust connection
A B (a) B (b) C D E
mm 790 965 1105 1770 775 835
F G H I J K
mm 750 395 605 740 240 175
L
mm 110

Installation manual 13
3.2.2 Technical data
Weight, net kg 210
Drum volume liters 255
Drum diameter mm 755
Drum depth mm 595
Drum speed, medium load rpm 43
Rated capacity, filling factor 1:18 (Max. load) kg 14.2
Rated capacity, filling factor 1:22 (Recommended load) kg 11.6
Heating: Steam at 700 kPa kW 15.0
Steam pressure kPa 100–1000
Optimum air flow** m3/h 460
Optimum static back pressure** Pa 550
Maximum static back pressure** Pa 570
Sound power/pressure level at drying* dB(A) 72/56
Heat emission of installed power, max % 15
* Sound power levels measured according to ISO 60704.
** In a cold empty machine.
Connections
Air outlet ⌀mm 200
Steam inlet/outlet ISO 7/1–R1

14 Installation manual
3.3 Gas heated machines
3.3.1 Drawing
1
2
A
C
BD
E
F
I
3
J
K
G
H
4
5
fig.X00719
1 Operating panel
2 Door opening, ⌀580 mm
3 Electrical connection
4 Gas connection
5 Exhaust connection
A B C D E F
mm 795 965 1770 775 835 750
G H I J K
mm 110 60 270 240 175

Installation manual 15
3.3.2 Technical data
Weight, net kg 202
Drum volume liters 255
Drum diameter mm 755
Drum depth mm 595
Drum speed, medium load rpm 43
Rated capacity, filling factor 1:18 (Max. load) kg 14.2
Rated capacity, filling factor 1:22 (Recommended load) kg 11.6
Heating: Gas kW 13.5
Optimum air flow** m3/h 460
Optimum static back pressure** Pa 550
Maximum static back pressure** Pa 570
Sound power/pressure level at drying* dB(A) 72/56
Heat emission of installed power, max % 15
* Sound power levels measured according to ISO 60704.
** In a cold empty machine.
Note!
The default gas appliances are built to run on either GNH or LPG gas where shall be installed at not over than
610 m (2001 ft) high altitude otherwise a kit for high altitude must be installed to the machine.
For the kit No. please refer to the spare parts list.
Connections
Air outlet ⌀mm 200
Gas connection 1/2” ISO 7/1–R1/2

16 Installation manual
4 Setup
4.1 General
The principle work flow to setup or install this machine is as follows:
Gas-, Electric-, Steam heating:
1. Unpacking
2. Positioning/siting, levelling or/and securing the machine.
3. Correcting the fresh air/air intake's size, exhaust duct's size and pipe(s) connections in considering a stand-alone
machine or sharing exhaust duct.
4. Electric connections, connect the power supply to the machine.
5. Air flow or static back pressure adjustments in a cold empty machine in considering a stand-alone machine or
sharing exhaust duct.
6. Gas connection, gas converting, high altitude kit installation. (For gas heated machine).
7. Function check.
8. Option functions check.
More details are described in each part of this installation manual.
Heat pump heating:
1. Unpacking
2. Positioning/siting, levelling or/and securing the machine.
3. Correcting the fresh air to compensate the heat emission of machine(s) and connect the drain(s).
4. Electric connections, connect the power supply to the machine.
5. Function check.
6. Option functions check.
More details are described in each part of this installation manual.
4.2 Unpacking
Note!
A minimum of two persons are required for the unpacking of the unit.
Remove the filter drawer and demount the lower front panel.
Demount the rear panel.
6x
fig.X00692

Installation manual 17
Remove the bolts between the machine and pallet.
Remove the machine from the pallet.
Note!
When moving the machine, handle it with care. The drum has no transport clamps.
2x
fig.X00693
Place the machine on its final position, rolling it on its wheels.

18 Installation manual
4.3 Recycling instruction for packaging
4
5
6
3
1
2
2
fig.X02406
Fig. Description Code Type
1 Wrapping film LDPE 4 Plastics
2 Corner protection PS 6 Plastics
3 Cardboard packaging PAP 20 Paper
4 Pallet FOR 50 Wood
5Screw FE 40 Steel
6 Plastic bag PET 1 Plastics

Installation manual 19
4.4 Wheels
For ergonomic reasons the machine is equipped with wheels.
The wheels make it easy to move the machine without lifting it.
The wheels can only be used as long as the feet of the machine are not lowered.
4x
fig.X00717
4.5 Siting
The figure shows recommended distance to walls and/or other machines.
B
C
A
A
D=C+B
E
F
12
Y
1= Top view
2 = Side view on built in machine
Y = For built-in machines it is recommended that the wall section Y is a removable finish piece. If so, E and F can be 0.
fig.X00959A
A 5–500 mm (Min. 5 mm)
B 500 mm (Min. 200 mm)
C Depth of machine
D D = C + B (Min. 1220 mm to be able to use the machine)
E Min. 40 mm
F Min. 25.4 mm (The overhead soffit may be used to close the gap above the machine. Min. required clearance: 0 mm)

20 Installation manual
Note!
The machine should be positioned so that there will be enough space for working, both for the user and
service personnel.
Respecting the given recommendations will provide easy access for maintenance and service operations.
In case of space limitations, it is possible to install machines without respecting to the given recommendations. If so,
keep in mind that it might be necessary to disconnect and move other machines to be able to reach and perform
service on affected machine.
4.6 Mechanical installation
Level the machine with the feet of the machine. The maximum height adjustment of the feet is 15 mm.
Note!
It is important that the machine stand steady on all four feet and not directly on the wheels. The wheels must
only be used when moving the machine.
4x
fig.X00694
Remount the panels.