Electrolux Professional Compass Pro TD6-24S User manual

Installation manual
Tumble dryer
TD6–24S
Compass Pro
Type N3...
Original instructions
438917590/GB, IE
2023.03.17

Contents
Contents
1 Safety Precautions ..............................................................................................................................5
1.1 Additional safety precautions for gas heated tumble dryer .............................................................7
1.2 General safety information..........................................................................................................7
1.3 Commercial use only..................................................................................................................7
1.4 Copyright ..................................................................................................................................7
1.5 Symbols....................................................................................................................................7
2 Warranty terms and exclusions.............................................................................................................8
3 Technical data.....................................................................................................................................9
3.1 Drawing ....................................................................................................................................9
3.2 Technical data .........................................................................................................................10
4 Setup ............................................................................................................................................... 11
4.1 Unpacking............................................................................................................................... 11
4.2 Recycling instruction for packaging ...........................................................................................12
4.3 Siting ......................................................................................................................................13
4.4 Connection to network..............................................................................................................14
4.5 Mechanical installation .............................................................................................................14
4.5.1 Securing the machine .....................................................................................................15
4.5.2 Connection branch .........................................................................................................15
5 Evacuation system ............................................................................................................................16
5.1 Air principle .............................................................................................................................16
5.2 Fresh air..................................................................................................................................16
5.3 Exhaust duct ...........................................................................................................................17
5.4 Shared exhaust duct ................................................................................................................18
5.5 Exhaust dimensioning ..............................................................................................................18
6 Gas connection .................................................................................................................................19
6.1 Fasten the label .......................................................................................................................19
6.2 General...................................................................................................................................19
6.3 Gas installation........................................................................................................................20
6.4 Table of pressure and adjustment..............................................................................................21
6.5 Test run...................................................................................................................................22
6.6 Converting instructions.............................................................................................................22
6.7 Data label................................................................................................................................24
7 Electrical connection..........................................................................................................................25
7.1 Electrical installation ................................................................................................................25
7.2 Single-phase connection ..........................................................................................................25
7.3 Three-phase connection...........................................................................................................26
7.4 Electrical connections ..............................................................................................................27
8 At first power up ................................................................................................................................28
8.1 Select language.......................................................................................................................28
8.2 Set time and date.....................................................................................................................28
8.3 Activate/Deactivate the service alarm ........................................................................................28
9 Function check..................................................................................................................................29
10 Disposal information..........................................................................................................................31
10.1 Disposal of appliance at end of life ............................................................................................31
10.2 Disposal of packing..................................................................................................................31
The manufacturer reserves the right to make changes to design and component specifications.

Installation manual 5
1 Safety Precautions
• Servicing shall be carried out only by authorized personnel.
• Only authorized spare parts, accessories and consumables shall be used.
• The machine is not to be used if industrial chemicals have been used for cleaning.
• Do not dry unwashed items in the machine.
• Items that have been soiled with substances such as cooking oil, acetone, alcohol, pet-
rol, kerosene, spot removers, turpentine, waxes and wax removers should be washed
in hot water with an extra amount of detergent before being dried in the machine.
• Items such as foam rubber (latex foam), shower caps, waterproof textiles, rubber
backed articles and clothes or pillows fitted with foam rubber pads should not be dried
in the machine.
• Fabric softeners or similar products should be used as specified by the fabric softener
instructions.
• The final part of a drying cycle occurs without heat (cool down cycle) to ensure that the
items are left at a temperature that ensures that the items will not be damaged.
• Remove all objects from pockets such as lighters and matches.
• WARNING. Never stop the machine before the end of the drying cycle unless all items
are quickly removed and spread out so that the heat is dissipated.
• Adequate ventilation has to be provided to avoid the back flow of gases into the room
for appliances burning other fuels, including open fires.
• Exhaust air must not be discharged into a flue which is used for exhausting fumes from
appliances burning gas or other fuels.
• The machine must not be installed behind a lockable door, a sliding door or a door with
a hinge on the opposite side to that of the machine in such a way that a full opening of
the machine is restricted.
• If the machine has a lint trap this has to be cleaned frequently.
• The lint must not be accumulated around the machine.
• DO NOT MODIFY THIS APPLIANCE.
• When performing service or replacing parts, the power must be disconnected.
• When the power is disconnected, the operator must see that the machine is discon-
nected (that the plug is removed and remains removed) from any point to which he has
access. If this is not possible, due to the construction or installation of the machine, a
disconnection with a locking system in the isolated position shall be provided.
• In accordance with the wiring rules: mount a multi-pole switch prior to the machine to
facilitate installation and service operations.
• Stationary appliances not fitted with means for disconnection from the supply mains
having a contact separation in all poles that provide full disconnection under overvolt-
age category III, the instructions state that means for disconnection must be incorpo-
rated in the fixed wiring in accordance with the wiring rules.
• WARNING: The appliance must not be supplied through an external switching device,
such as a timer, or connected to a circuit that is regularly switched on and off by a utility.
• If different rated voltages or different rated frequencies (separated by a /) are stated at
the machine data plate, instructions for adjusting the appliance for operation at the re-
quired rated voltage or rated frequency are stated in the installation manual.
• The openings in the base, shall not be obstructed by a carpet.

6Installation manual
• Oil-affected items can ignite spontaneously, especially when exposed to heat sources
such as in a tumble dryer. The items become warm, causing an oxidation reaction in
the oil. Oxidation creates heat. If the heat cannot escape, the items can become hot
enough to catch fire. Piling, stacking or storing oil-affected items can prevent heat from
escaping and so create a fire hazard.
• If it is unavoidable that fabrics that contain vegetable or cooking oil or have been conta-
minated by hair care products be placed in a tumble dryer they should first be washed
in hot water with extra detergent – this will reduce, but not eliminate, the hazard.
• Maximum mass of dry cloth: 2 x 23.5 kg.
• A-weighted emission sound pressure level at working stations: 70 dB(A).
• Additional requirements for the following countries; AT, BE, BG, HR, CY, CZ, DK, EE,
FI, FR, DE, GR, HU, IS, IE, IT, LV, LT, LU, MT, NL, NO, PL, PT, RO, SK, SI, ES, SE, CH,
TR, UK:
– The appliance can be used in public areas.
– This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and knowl-
edge if they have been given supervision or instruction concerning use of the appliance
in a safe way and understand the hazards involved. Children shall not play with the ap-
pliance. Cleaning and user maintenance shall not be made by children without
supervision.
• Additional requirements for other countries:
– This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety. Children should be supervised to ensure that they
do not play with the appliance.

Installation manual 7
1.1 Additional safety precautions for gas heated tumble dryer
• Before installation, check that the local distribution conditions, nature of gas and pres-
sure and the adjustment of the appliance are compatible.
• The machine is not to be installed in rooms containing cleaning machines with per-
chloroethylene, TRICHLOROETHYLENE or CHLOROFLUOROCONTAINING HY-
DROCARBONS as cleaning agents.
• NOTE: it is pointed out that the connection and commissioning of appliances complying
with this standard are subject to observance of the installation regulations in force in
the countries where these appliances are marketed.
• Connection to the appliance shall be made with a flexible hose suitable for the appli-
ance category in accordance with national installation regulations of the country of des-
tination and that in case of doubt the installer shall contact the supplier.
• The appliance should be installed on non-flammable materials for the floor, worktop
and/or wall close to the appliance if required.
• If you can smell gas:
– Do not switch on any equipment
– Do not use electrical switches
– Do not use telephones in the building
– Evacuate the room, building or area
– Contact the person responsible for the machine
1.2 General safety information
In order to prevent damage to the electronics (and other parts) that may occur as the result of condensation, the ma-
chine should be placed in room temperature for 24 hours before being used for the first time.
1.3 Commercial use only
The machine/machines covered by this manual is/are made for commercial and industrial use only.
1.4 Copyright
This manual is intended solely for consultation by the operator and can only be given to third parties with the permis-
sion of Electrolux Professional company.
1.5 Symbols
Caution
Caution, hot surface
Caution, high voltage
Read the instructions before using the machine

8Installation manual
2 Warranty terms and exclusions
If the purchase of this product includes warranty coverage, warranty is provided in line with local regulations and sub-
ject to the product being installed and used for the purposes as designed, and as described within the appropriate
equipment documentation.
Warranty will be applicable where the customer has used only genuine spare parts and has performed maintenance
in accordance with Electrolux Professional user and maintenance documentation made available in paper or elec-
tronic format.
Electrolux Professional strongly recommends using Electrolux Professional approved cleaning, rinse and descaling
agents to obtain optimal results and maintain product efficiency over time.
The Electrolux Professional warranty does not cover:
• service trips cost to deliver and pick up the product;
• installation;
• training on how to use/operate;
• replacement (and/or supply) of wear and tear parts unless resulting from defects in materials or workmanship re-
ported within one (1) week from the failure;
• correction of external wiring;
• correction of unauthorized repairs as well as any damages, failures and inefficiencies caused by and/or resulting
from;
– insufficient and/or abnormal capacity of the electrical systems (current/voltage/frequency, including spikes and/
or outages);
– inadequate or interrupted water supply, steam, air, gas (including impurities and/or other that does not comply
with the technical requirements for each appliance);
– plumbing parts, components or consumable cleaning products that are not approved by the manufacturer;
– customer’s negligence, misuse, abuse and/or non-compliance with the use and care instructions detailed within
the appropriate equipment documentation;
– improper or poor: installation, repair, maintenance (including tampering, modifications and repairs carried out
by third parties not authorized third parties) and modification of safety systems;
– Use of non-original components (e.g.: consumables, wear and tear, or spare parts);
– environment conditions provoking thermal (e.g. overheating/freezing) or chemical (e.g. corrosion/oxidation)
stress;
– foreign objects placed in- or connected to- the product;
– accidents or force majeure;
– transportation and handling, including scratches, dents, chips, and/or other damage to the finish of the product,
unless such damage results from defects in materials or workmanship and is reported within one (1) week of deliv-
ery unless otherwise agreed;
• product with original serial numbers that have been removed, altered or cannot be readily determined;
• replacement of light bulbs, filters or any consumable parts;
• any accessories and software not approved or specified by Electrolux Professional.
Warranty does not include scheduled maintenance activities (including the parts required for it) or the supply of
cleaning agents unless specifically covered within any local agreement, subject to local terms and conditions.
Check on Electrolux Professional website the list of authorized customer care.

Installation manual 9
3 Technical data
3.1 Drawing
A
F
H
C
B
I
J
G
E
K
N1
N2
L
M
O
P
N3
D
2
1
1
2
5
5
5
4
3
fig.W00530
1 Operating panel
2 Door opening, ⌀687 mm
3 Electrical connection
4 Gas connection
5 Exhaust connection
A B C D E F
mm 870 1335 2085 35 1310 1240
G H I J K L
mm 290 215 1085 140 40 35
M N1 N2 N3 O P
mm 30 110 145 190 815 2185

10 Installation manual
3.2 Technical data
Weight, net kg 440
Drum volume litres 2 x 423
Drum diameter mm 832
Drum depth mm 757
Drum speed rpm 43–44
Rated capacity, filling factor 1:18 (Max. load) kg 2 x 23.5
Rated capacity, filling factor 1:22 (Recommended load) kg 2 x 19.2
Heating: Gas kW 2 x 27.5
Air flow m3/h 2 x 850
Duct connection, exhaust ⌀mm 1 x 200
Maximum static back pressure, Gas 50 Hz / 60 Hz** Pa 340 / 520
Gas pipe connection ISO 7/1–R3/4
Sound power/pressure level at drying* dB(A) 77/60
Heat emission of installed power, max % 15
* Sound power levels measured according to ISO 60704.
** Static back pressure value measured in NTC position, in cold empty machine and only run that pocket at a time.
Note!
The default gas appliances are built to run on either GNH or LPG gas where shall be installed at not over than
610 m (2001 ft) high altitude otherwise a kit for high altitude must be installed to the machine.
For the kit No. please refer to the spare parts list.

Installation manual 11
4 Setup
4.1 Unpacking
Note!
Two persons are recommended for the unpacking.
Remove the bolts between the machine and pallet.
Remove the bottom filter drawer. Remove the panels on both sides of the filter drawer. Remove the two bolts at the
front.
Remove the lower rear panel and remove the bolts.
fig.X00058
Remove the machine from the pallet.
Note!
When moving the machine, handle it with care. The drum has no transport clamps.
Place the machine on its final position.

12 Installation manual
4.2 Recycling instruction for packaging
4
5
6
3
1
2
2
fig.X02460
Fig. Description Code Type
1 Wrapping film LDPE 4 Plastics
2 Corner protection PS 6 Plastics
3 Cardboard packaging PAP 20 Paper
4 Pallet FOR 50 Wood
5Screw FE 40 Steel
6 Plastic bag PET 1 Plastics

Installation manual 13
4.3 Siting
The figure shows recommended distance to walls and/or other machines.
B
C
A
A
D=C+B
E
F
12
Y
1= Top view
2 = Side view on built in machine
Y = For built-in machines it is recommended that the wall section Y is a removable finish piece. If so, E and F can be 0.
fig.X00959A
A 5–500 mm (Min. 0 mm, the units may be installed against one another)
B 500 mm (Min. 200 mm)
C Depth of machine
D D = C + B (Min. 1220 mm to be able to use the machine)
E Min. 20 mm
F Min. 25.4 mm (The overhead soffit may be used to close the gap above the machine. Min. required clearance: 0 mm)
Note!
The machine should be positioned so that there will be enough space for working, both for the user and
service personnel.
Respecting the given recommendations will provide easy access for maintenance and service operations.
In case of space limitations, it is possible to install machines without respecting to the given recommendations. If so,
keep in mind that it might be necessary to disconnect and move other machines to be able to reach and perform
service on affected machine.

14 Installation manual
4.4 Connection to network
If several machines are to be connected to a network, the knock-outs (A) in the side panels must be removed before
installation.
A bushing for network cables must be installed from the inside in the right-hand side panel. The bushing must be
pushed right through the hole in the left-hand side panel on the side of the machine.
A
fig.7717
4.5 Mechanical installation
Level the machine with the feet of the machine. The maximum height adjustment of the feet is 15 mm.
fig.W00120A
Remount the panels.

Installation manual 15
4.5.1 Securing the machine
To ensure steadiness of the machine it is important to fasten the machine to the foundation.
Fasten the four fittings (A) to the foundation using four x M10 set screws (B). If the four fittings are not supplied, order
kit No. 487193544.
Fasten the machine to the fittings.
A
B
15.3 mm / 9/16 inch
833.5 mm / 32 13/16 inch
774 mm / 30 1/2 inch
43.3 mm / 1 11/16 inch
1233.5 mm / 48 9/16 inch
1174 mm / 46 1/4 inch
45 mm / 1 3/4 inch
73 mm / 2 7/8 inch
FRONT
fig.X00161
4.5.2 Connection branch
Mount the enclosed branch at the top of the exhaust plenum with four screws.
fig.7655

16 Installation manual
5 Evacuation system
5.1 Air principle
The fan creates low pressure in the machine, drawing air into the drum via the heating unit.
The heated air passes through the garments and the drum holes.
The air then flows out through a lint filter positioned below the drum. Then the air is evacuated through the fan and
exhaust system.
Note!
It is very important that the machine gets enough fresh air in order to get the best drying result.
5.2 Fresh air
For maximum efficiency and the shortest possible drying time, it is important to ensure that fresh air is able to enter
the room from the outside in the same volume as that is blown out of the room.
To avoid draught in the room it is important to place the air inlet behind the machine.
Provisions for adequate air supply: The area of the air inlet opening should be five times the size of the exhaust pipe
area. The area of the inlet opening is the area through which the air can flow without resistance from the grating/slat-
ted cover.
10 x A
A
fig.W00122
Note!
Gratings/slatted covers often block half of the total fresh air vent area. Remember to take this into account.

Installation manual 17
5.3 Exhaust duct
• Only rigid or flexible metal duct should be used for exhausting.
• Plastic ducting is not to be used.
• Recommended material for exhaust is galvanized steel.
• The duct is not to be assembled with screws or other fastening means that extend into the duct and catch lint.
• The exhaust air should not be vented into a wall, a ceiling, or a concealed space of building.
• The exhaust duct must lead clear of the building as condensation may cause frost damage to the building.
• The exhaust duct must lead to the outdoors.
• The exhaust duct must be placed in such a way that it is protected on the outside.
• The exhaust duct must be smooth on the inside (low air resistance).
• The exhaust duct must have gentle bends.

18 Installation manual
5.4 Shared exhaust duct
It is recommended that each machine is connected to a separate exhaust duct.
When several machines shall use the same exhaust duct the exhaust duct must increase before each machine is
added. The individual ducts should enter the main duct at an angle of 45° or less and in the direction of airflow. The
recommended diameter increase progression is the one in the table.
If several machines are installed on the same exhaust pipe, it is recommended to adjust the airflow on the machines
when all machines are started and running a program with no heat.
Please consider that unnecessarily large ducts create issues with the draught.
fig.W00123
Number of machines 1 2 3 4 5 6 7 8 9 10
Exhaust duct ⌀mm 200 315 400 400 500 500 630 630 630 800
Recommended area
of fresh air intake
m20.32 0.78 1.26 1.26 1.96 1.96 3.12 3.12 3.12 5.02
Minimum area of
fresh air intake
m20.16 0.32 0.48 0.64 0.8 0.96 1.12 1.28 1.44 1.6
The exhaust duct diameter must not be reduced.
5.5 Exhaust dimensioning
It is important that the machine has correct air volume compared to each machines power.
If the air flow is smaller or larger this will result in a longer drying period.
If the outlet pipe is long or the ventilation is not properly designed we recommend to clean the outlet pipes periodi-
cally. Usually, longer ducts need more frequent cleaning.
The exhaust pipes shall be short in order for the machine to work in the best way.
All cover panels must be mounted in order for the machine to work in the best way.

Installation manual 19
6 Gas connection
6.1 Fasten the label
Before installing the machine fasten the label “Read the user instructions” on the inside of the door in a suitable place
and at the front panel.
The label must have the correct country code, choose the correct label from the gas kit.
GB, IE
Read the technical
instructions before
installing the appli-
ance.
Read the user
instructions before
lighting the appliance.
This appliance may
only be installed in a
room if the room
meets the appropriate
ventilation require-
ments specified in the
national installation
regulations.
Art. No. ...........
GB,IE
Readthe technical
instructionsbefore
installingthe appli-
ance.
Readthe user
instructionsbefore
lightingthe appliance.
Thisappliance may
onlybe installed in a
roomifthe room
meetsthe appropriate
ventilationrequire-
mentsspecified in the
nationalinstallation
regulations.
Art. No. ...........
fig.7514
6.2 General
May only be carried out by qualified personnel.
Mount a shut-off valve upstream from the machine.
The factory nozzle pressure setting corresponds to the fuel value given on the data label.
Check that the nozzle pressure and fuel value correspond with the values in the gas tables on the following pages. If
not, contact the supplier.
Bleed the pipe system before connecting the machine.
Note!
After connection all joints must be checked. There must not be any leaks.

20 Installation manual
6.3 Gas installation
This gas appliance is build to run on natural gas (group I2H and I2E), commonly identified by GNH.
This default gas appliance is built to be installed at not over than 610 m (2001 ft) high altitude otherwise a kit for high
altitude must be installed to the machine. For the kit No. please refer to the spare parts list.
The data label shows the injector size and the injector pressure and the countries that use this gas quality:
AL Albania IE Ireland
AT Austria IS Iceland
BE Belgium IT Italy
BG Bulgaria LT Lithuania
CH Switzerland LU Luxembourg
CY Cyprus LV Latvia
CZ Czech Republic MK Republic of Macedonia
DE Germany MT Malta
DK Denmark NL Netherlands
EE Estonia NO Norway
ES Spain PL Poland
FI Finland PT Portugal
FR France RO Romania
GB United Kingdom SE Sweden
GR Greece SI Slovenia
HR Croatia SK Slovakia
HU Hungary TR Turkey
You should check the kind of energy gas that is available in your place and check high altitude of the machine located
place.
There are many gas types of the same kind but the machine should be equipped with different kinds of nozzles de-
pending on the gas type.