Electrolux Professional WB6-20 User manual

Installation manual
Washer-extractors
WB6–20 — WB6–27 — WB6–35 Clean Room
Original instructions 05201149/EN

Contents
Contents
1 Safety precautions...............................................................................................................................5
1.1 Symbols....................................................................................................................................8
1.2 Personal protection equipment....................................................................................................9
1.3 Preliminary instructions ............................................................................................................10
2 Environmental information .................................................................................................................10
3 Note about the A.C. power .................................................................................................................12
4 Data plate explanation .......................................................................................................................13
5 Locking and tagging procedure...........................................................................................................17
6 Handling...........................................................................................................................................18
6.1 Lifting with a fork-lift truck .........................................................................................................18
6.2 Lifting with handlings straps......................................................................................................18
7 Packing-Weight.................................................................................................................................19
7.1 Packing...................................................................................................................................19
7.2 Weight ....................................................................................................................................20
8 Technical characteristics ....................................................................................................................21
8.1 Technical data .........................................................................................................................21
8.2 Connections ............................................................................................................................21
8.3 Dimensions — WB6–20 – WB6–27 – WB6–35...........................................................................24
9 Sound levels .....................................................................................................................................26
10 Working place lighting........................................................................................................................26
11 Supplies ...........................................................................................................................................26
12 Barrier partition .................................................................................................................................27
13 Mechanical installation.......................................................................................................................28
13.1 Unpacking...............................................................................................................................28
13.2 Installation...............................................................................................................................28
13.3 Installing the shock absorber runners ........................................................................................28
13.4 Instructions for securing the machine on the ground ...................................................................29
14 Remove of the transport locks fitted ....................................................................................................30
14.1 Remove of transport locks of casing : ........................................................................................30
14.2 Remove of transport locks fitted : ..............................................................................................30
15 Bath inlet (water + detergents)............................................................................................................31
15.1 Connection of external water supply ..........................................................................................32
16 Drain connection ...............................................................................................................................33
17 Electricity power supply .....................................................................................................................33
18 Liquid detergents connection..............................................................................................................36
18.1 Connection scheme of liquid detergents ....................................................................................36
18.2 Electrical liquid detergents' connection ......................................................................................37
19 Indirect steam heating .......................................................................................................................39
20 Compressed air connection................................................................................................................40
21 Air vent connection............................................................................................................................42
22 Feeder cable sections........................................................................................................................42
23 Function checks ................................................................................................................................45
24 Conversion of measurement units.......................................................................................................47
25 Disposal information..........................................................................................................................48
25.1 Disposal of appliance at end of life ............................................................................................48
25.2 Disposal of packing..................................................................................................................48
The manufacturer reserves the right to make changes to design and component specifications.

Installation manual 5
1 Safety precautions
This machine should be installed in conformance to the health and safety regulations, and only used in a sufficiently aerated
area.
Check the instructions before installing or using the machine.
Before any use, it is compulsory to read the instruction handbook.
Users must have learnt how the machine operates.
This device must not be installed in places accessible to the public.
The machine is only intended for water-wash use.
Do not allow minors to use the machine.
Do not hose down the machine with water.
Only use detergent intended for water-wash of textiles Never use dry cleaning agents.
The machine's door lock must under no circumstances be bypassed.
Servicing shall be carried out only by authorized personnel.
If the machine develops a fault, this must be reported to the person in charge as soon
as possible. This is important both for your safety and that of others.
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety and understand the hazards involved.
Do not modify this appliance.
Only authorized spare parts shall be used.
It is forbidden to wash textiles soaked with solvents.
In order to prevent damage to the electronics (and other parts) that may occur as the
result of condensation, the machine should be placed in room temperature for 24 hours
before being used for the first time.
In case of a gas heated machine, do not assemble the machine on premises contain-
ing a dry cleaning machines or other similar machines.
Make sure note to over load the machine.
Please wash only items offering appropriate distribution inside the drum. Do not wash
items such as mattresses or shoes. Call our technical departments before washing
nonstandard items. Noncompliance with these instructions may void the manufactur-
er's guarantee in case of abuse of the washer-extractor.
IMPORTANT
Never try to open the outer drum door before the complete stop of the cage.
CAUTION
Disconnect all the sources of energy before any intervention on the machine.

6Installation manual
The machines comply with the European Directive EMC (Electromagnetic Compatibil-
ity). They have been tested in laboratory and approved as such. It is so prohibited to
add wires or nonshielded electric cables in the cabinets except for option and executed
by qualified technician, strands or cables' troughs.
Considering that the volume of the outer drum is superior to 150 litres, the standard
kept for the electric part is the IN 60204.
Never use the main switch as an emergency stop. Use it only when the machine does
not work in progress. Instead of that, use the emergency stop buttons in both sides of
the machine.
CAUTION
The machine can work without the protective casing when the electric supply is not cut
off.
Interlock the main isolating switch with a padlock.
Close the steam or gas inlet valves.
CAUTION
With AIDO(Automatic Inner Door Opening) option, Take care of the disc of the opening
system on your side. Risk of cutting with the edge of the disc!!
Take care also of the locking system on your side; risk of cutting with the edge of the
plate!!
CAUTION
When you put your hands into the drum, take care of the edge of the outer drum doors
on yours sides. Risk of cutting with the edge of the metal plate!!
CAUTION
In case of barrier washing machine (two outer doors) , make sure to have more pres-
sure in the clean linen area (unloading side) than in the dirty linen area (loading side)
to be sure to not suck bacteria from the dirty side to the clean side.

Installation manual 7
IMPORTANT
Ensure that the machine is not loaded beyond its nominal capacity (see "Specific load"
in the instruction booklet’s technical characteristics).
An excessive load has consequences for the lifetime of the machine’s organs, as
follows:
• Rapid destruction of the suspension elements (springs, shock absorbers);
• Excessive fatigue of motorization elements (engine, belt);
• Rapid reduction of lifetime of drum bearings (rolling bearings);
• Opening and destruction of drum doors and tank doors during oil dehydration.
This is particularly important for your safety and that of others.
The consequence is an immediate cancellation of the warranty.
THINK OF THE ENVIRONMENT!
The use and handling of chemical products such as detergent, chlorine, acids, desca-
ling agents, etc may create hazards for health and environment ; the following precau-
tions should be taken:
• Do not breathe the dusts or steam;
• Avoid contact with skin or eyes (may cause burns);
• In case of important spillage, wear a protecting mask, gloves, and eye protectors;
• Handle with care;
• Consult the use and first aid advice on the packing;
• Do not dispose pure products in the environment.

8Installation manual
1.1 Symbols
Caution.
Caution, presence of dangerous current.
Caution, hot surface.
Read the instructions before using the machine.
Warning, do not operate with casing removed.

Installation manual 9
1.2 Personal protection equipment
Given below is a summary table of the Personal Protection Equipment (PPE) to be used
during the various phases of the machine’s service life.
Phase Protection
garments
Safety
footwear
Gloves Glasses Ear protectors Mask Safety helmet
Transport XO
Handling XO
Unpacking XO
Installation X O
Normal use X X X X
Adjustments OX
Routine
cleaning OX X O
Extraordinary
cleaning OX X O
Maintenance OXO
Dismantling OXO
Scrapping OXO
Legend :X: PPE required ; O: PPE available or to be used if necessary.
Normal use : Safety footwear must be defined for a use on a wet floor. And use glasses
and gloves to manipulate chemical products.

10 Installation manual
1.3 Preliminary instructions
WARNING
Risk of jamming when opening the lower door for unloading
WARNING
Risk of jamming with trolley and lower door when opening (if trolley height = 850mm)
WARNING
Risk of the upper door being raised quickly on loading
WARNING
After the installation, Send back the commissionning form ,signed document, to Elec-
trolux to validate the warrantly of the product.
2 Environmental information
Concerned by providing the end user with useful and necessary environmental information, we wish to precise:

Installation manual 11
• Data about energetic consumptions, wastes (atmospheric and liquid) and sound level are indicated in the para-
graph «Technical characteristics».
• Foreseeing its recycling, this machine is fully dismantable.
• This machine is free from any asbestos.
• In conformity with French regulations.
• In the other countries, we recommend that you comply with the legislation in force in the country where the ma-
chine is installed.
• In France, all owners of packing waste producing a weekly volume below 1100 litres can forward these to the local
collection and treatment department. If exceeding this volume, the owners of packing waste will ensure their valu-
ation by reuse, recycling or, any other action aiming at producing reusable materials or energy... or provide them
contractually to a certified intermediate authorised to transport, trade or broke waste.
Therefore, this forbid:
– land filling raw waste;
– open air burning or incineration without energy collection.
• Packaging of our machines are according with the french legislation related to environment requirements.
For additional information, do not hesitate to consult with our environmental department.
Scrapping of machine
When the machine is no longer to be used, it must be submitted to a recycling facility for destruction.
The majority of the components in the machine can be reused, but it also contains other materials that must be
taken care of in the correct way.
Therefore, never mix the machine or its parts with domestic waste as this may lead to health hazards or dam-
age to the environment.

12 Installation manual
3 Note about the A.C. power
According to the EN 60204-1:1997 standard, the machine is provided for A.C. supplies corresponding to the ex-
tracted characteristics below :
4.3.2 A.C. supplies
Voltage:
Steady state voltage: from 0.9 to 1.1 of nominal voltage.
Frequency:
from 0.99 to 1.01 of nominal frequency continuously.
from 0.98 to 1.02 short time.
Harmonics:
Harmonic distortion not to exceed 10 % of the total r.m.s. voltage between live conductors for the sum of the second
through to the fifth harmonic. An additional 2 % of the total r.m.s. voltage between live conductors for the sum of the
sixth through to the 30th harmonic is permissible.
Voltage unbalance:
Neither the voltage of the negative sequence component nor the voltage of the zero sequence component in three-
phase supplies shall exceed 2 % of the positive sequence component.
Voltage interruption:
Supply interrupted or at zero voltage for not more than 3 ms at any random time in the supply cycle. There shall be
more than 1 second between successive interruptions.
Voltage dips:
Voltage dips shall not exceed 20 % of the peak voltage of the supply for more than one cycle. There shall be more
than 1 second between successive dips.

Installation manual 13
4 Data plate explanation
In this chapter, you will find the explanation of the different data input on the data plate of your product.
• Commercial name : Usual name of your product ( i.e. WB6–20).
• Type : Type of your product (you have the same on the Declaration of Conformity CE if delivered with CE
certification).
• Model : Model of your product (can be different of commercial name ) (i.e WSBA6180H17 for commercial name
WB6–20) .
• Serial Number : serial number of your product which indicate the week of the production of your product (the first 4
digit indicate the year and the week of production)
and the plant where it has been produced (finish by 17)
• Product N°: Product number of your product.
• Date : The date of the end of manufacture of your product
• Capacity : for washer product, the maximum loaded weight of linen for your product (in kg)(i..e. 20 kg for WB6–20)
• Some technical data depending of the heating of your product : see list below :
• Some technical data depending of the voltage ordered.
the voltage looks like that 380–415V 3 50–60Hz
under this, you find the protection request for your product (i.e 16 A)
• Different logos are available on your data plate .
They represent the different certification obtained for your product
CE, EAC
ETL intertek for USA and Canada countries
• QR code : when you scan it, you will be able to obtain the full documentation for your product (Complete installa-
tion and user manuals)
• Standardized protection index of your product : IP24D

14 Installation manual
Electrical heating :
• P.Max : maximum power installed of your product
• Power of the motorization in kW and its isolation class (F) .
• Heating power in W .

Installation manual 15
Gas heating :
Left side
• P.Max : maximum power installed of your product
• Power of the motorization in kW and its isolation class (F) .
• Heating power in W .
• Gas approval number depending on your machine except ETL product (begin by1312/........)
Right side
• Qn (Hi) : heating power of your product
• Installed gas type , its pressure, its injector diameter and its consumption .
• 3 Other gas type compatible with their pressure, their injectors diameter

16 Installation manual
Steam heating :
Left side
• P.Max : maximum power installed of your product
• Power of the motorization in kW and its isolation class (F) .
• Heating power in W .
Right side
• P.Maxi. (kPa) maximum pressure
For additional information, do not hesitate to consult with our quality department.

Installation manual 17
5 Locking and tagging procedure
A red insert at the beginning of this instruction handbook schematically shows the locking and tagging procedure de-
scribed below. If you wish, you can detach this insert and display it close to the machine to remind maintenance per-
sonnel of the safety instructions.
Always respect items 2, 3 and 4 carefully before doing any repair or maintenance work on
the machine.
Put the main switch to Off
and lock the handle with a
padlock in one of the
three holes provided for
this purpose.
Close the stop valves for
the other supplies (steam,
gas, thermal fluid, com-
pressed air) to stop and
lock their handle with a
padlock.
Open the fixed protectors
(casings, doors) with the
key provided or a special
tool.
Do the maintenance.
Close and carefully lock the fixed protectors.
Unlock the stop valves and the main switch.

18 Installation manual
6 Handling
Important
It is obligatory that all these operations are undertaken by handling specialists.
Before any handling, check that the four transport locks fitted are still in place and well-tightened.
To do so, remove the front and rear casings and check presence of four locks (B).
6.1 Lifting with a fork-lift truck
Warning
You should never handle the machine in its longitudinal side (any other than shown on the drawing below) with a
fork-lift truck. Important risk of parts deterioration for those fixed under the machine.
This can be carried out from the front or back, at the centre of the machine.
6.2 Lifting with handlings straps
Lifting in that case can only be done with handling straps (minimum capacity 1000 daN / 2200 lb) which bear weight
of the machine.
Remove the top cover and pass the straps in the lifting holes.

Installation manual 19
Caution
Make sure to place the straps correctly to avoid any bending of parts of the machine.
Caution
In order to avoid any bending of casings, you should never climb and stand on top of the machine.
7 Packing-Weight
7.1 Packing
Packing dimensions in mm/in Size A Size B Size C
Washer extractor type WB6–20 1065/41.92 1390/54.72 1830/72.04
Washer extractor type WB6–27 1220/48.03 1390/54.72 1830/72.04
Washer extractor type WB6–35 1440/56.69 1390/54.72 1830/72.04

20 Installation manual
7.2 Weight
Weight in kg/lb (machine + crate)*
Washer extractor type WB6–20 700/1543
Washer extractor type WB6–27 740/1631
Washer extractor type WB6–35 800/1764
* Precise weight depends on accessories fitted.