Electrolux EK 5731 User manual

1
GB
Mixed fuel gas cookers
Mod. EK 5731
35673-8402
Please read this instruction booklet before using the appliance
INSTRUCTION BOOKLET
All manuals and user guides at all-guides.com
all-guides.com

2
Important Safety Information
You MUST read these warnings carefully before installing or using the appliance. If you
need assistance, contact our Customer Care Department on 87 5 95 95
Installation
lThis cooker must be installed by qualified
personnel, according to the manufacturers
instructions and to the relevant British
Standards.
 This cooker is heavy. Take care when moving it.
lAny gas installation must be carried out by a
registered CORGI installer.
lRemove all packaging before using the cooker.
lEnsure that the gas and electrical supply
complies with the type stated on the rating plate,
located near the gas supply pipe.
lDo not attempt to modify the cooker in any way.
Child Safety
lThis cooker is designed to be operated by
adults. Do not allow children to play near or with
the cooker.
lThe cooker gets hot when it is in use. Children
should be kept away until it has cooled.
lChildren can also injure themselves by pulling
pans or pots off the cooker.
During Use
lThis cooker is intended for domestic cooking
only. It is not designed for commercial or
industrial purposes.
lWhen in use a gas cooker will produce heat
and moisture in the room in which it has been
installed. Ensure there is a continuous air supply,
keeping air vents in good condition or installing
a cooker hood with a venting hose.
lWhen using the cooker for a long period time,
the ventilation should be improved, by opening
a window or increasing the extractor speed.
lDo not use this cooker if it is in contact with
water. Do not operate the cooker with wet hands.
lEnsure the control knobs are in the OFF
position when not in use.
lDo not store flammable materials such as oven
gloves, tea towels etc. in the drawer.
lWhen using other electrical appliances, ensure
the cable does not come into contact with the
hot surfaces of the cooker.
lUnstable or misshapen pans should not be used
on the hob burners as unstable pans can cau-
se an accident by tipping or spillage.
lNever leave the cooker unattended when
cooking with oil and fats.
lThis cooker should be kept clean at all times.
A build-up of fats or foodstuffs could result in a
fire.
lNever use plastic dishes in the oven or on the
hob burners.
Never line any part of the oven with
aluminium foil.
lAlways ensure that the oven vent which is
located at the centre back of the hob is left
unobstructed to ensure ventilation of the oven
cavity.
lPerishable food, plastic items and areosols may
be affected by heat and should not be stored
above the cooker.
lThe appliance (EK 5731 W/GR only) is fitted
with a lid: this is designed as a dust cover when
closed, and as a splash-back when open. Do
not use for any other purpose.
lAfter using the cooker (EK 5731 W/GR only),
the lid MUST NOT be closed until the hob and
oven are completely cold. Do not use the lid to
switch off the gas supply. The gas supply should
always be turned off with the control knob.
Always ensure that the lid is free of any soilage
or spillage before opening it.
Service
lThis cooker should only be repaired or serviced
by an authorised Service Engineer and only ge-
nuine approved spare parts should be used.
Environmental Information
lAfter installation, please dispose of the
packaging with due regard to safety and the
environment.
lWhen disposing of an old appliance, make it
unusable, by cutting off the cable.
Keep this instruction book for future reference
and ensure it is passed on to any new owner.
These instructions are valid for UK only.
All manuals and user guides at all-guides.com

3
This appliance is manufactured
according to the following EEC
directives:
73/23 EEC - 9 /683 EEC - 93/68 EEC -
89/336 EEC - 9 /396 EEC,
current edition.
Contents
Oven Door Protection Device
All our appliances comply with the
European safety standards.
Nevertheless, in order to ensure the
highest safety level, and avoid small
children to be exposed to the heat
when the appliance is operated, it is
possible to fit a special ptotection
device to the oven door. This device
can be purchased in our Service Force
Centres, specifying the relevant code
(35791) and the Product No. shown on
the rating plate.
For the User For the Installer
Guide to Use the instructions
The following symbols will be found in the text to
guide you throughout the Instructions:
Safety Instructions
Step by step instructions for an
operation
Hints and Tips
Environmental information
F
Important Safety Information 2
Description of the Cooker 4
Control Panel 5
Operation 6
Before the First Use of the Oven 7
Using the Oven 8
Using the Conventional Oven 9
Grilling 11
Maintenance and Cleaning 12
Cleaning the Oven 13
Something Not Working 14
Important Safety Requirements 18
Installation 19
Electrical connections 21
Commissioning 22
Conversion from Natural to LPG Gas 23
All manuals and user guides at all-guides.com

4
Description of the Cooker
Rapid burner
Semi-rapid burner
Control panel
Oven door
Semi-rapid burner
Auxiliary burner
Storage
drawer
Cooker lid
(EK 5731 W-GR only)
grill and oven
mains on
front left
back left back rightfront right
temperature
All manuals and user guides at all-guides.com

5
mains on
temperature
Premier
grill and ovenfront leftback left back rightfront right
Control Panel
1. Cooker Operation Pilot Light
2. Oven Thermostat Pilot Light
3. Electric Ignition push button
4. Back left burner control knob (rapid)
5. Front left burner control knob (semi-rapid)
6. Front right burner control knob (auxiliary)
7. Back right burner control knob (semi-rapid)
8. Oven function control knob
8765
1
4
The Oven Cavity
Grill element Oven Light
3
2
Accessories
P
Q
Grill rive
Removable handle
Grill/roas ing pan
All manuals and user guides at all-guides.com

6
Operation
Ho urners
To light a burner, push in and turn the relevant
control knob anticlockwise to maximum position.
At the same time push the electric ignition button
which is marked with a little spark. Then adjust
the flame as required.
If the burner does not ignite, turn the control knob
to zero, and try again.
When switching on the mains, after
installation or a power cut, it is quite
normal for the spark generator to be
activated automatically.
To ensure maximum burner efficiency, you
should only use pots and pans with a flat bottom
fitting the size of the burner used (see table).
Burner minimum maximum
diameter diameter
Large (rapid) 18 mm. 26 mm.
Medium (semi-rapid) 12 mm. 22 mm.
Small (Auxiliary) 8 mm. 16 mm.
If you use a saucepan which is smaller
than the recommended size, the flame
will spread beyond the bottom of the
pan, causing the handle to overheat.
As soon as a liquid starts boiling, turn
down the flame so that it will barely keep
the liquid simmering.
Take care when frying food in hot oil or
fat, as the overheated splashes could
easily ignite.
If the control knobs become difficult to
turn, please contact your local
Electrolux Service entre.
All manuals and user guides at all-guides.com
all-guides.com

7
200
150
100
50
max
Electric Oven
Oven Function Control Kno
lOven switched off
l-max Range of temperature regulation for
conventional cooking
Oven light
Bottom heating element - The heat
comes from the bottom of the oven only
Top heating element - The heat comes
from the top of the oven only
Grill - The heat comes only from the top
element
Before the First Use of the Oven
Remove all packaging, both inside and
outside the oven, before using the oven.
Before first use, the oven should be heated
without food. During this time, an unpleasant
odour may be emitted. This is quite normal.
F1. Set the oven function control knob to
MAX.
2. Open a window for ventilation.
3. Allow the oven to run empty for
approximately 45 minutes.
This procedure should be repeated with the grill
function for approximately 5-1 minutes.
All manuals and user guides at all-guides.com

8
Using the Oven
 Always cook with the oven door closed.
 Stand clear when opening the drop
down oven door. Do not allow it to fall
open - support the door using the door
handle, until it is fully open.
 The oven has four shelf levels, and is
supplied with one shelf.
The shelf positions are counted from the
bottom of the oven as shown in the
diagram.
It is important that the shelf is correctly
positioned as shown in the diagram.
 Do not place cookware directly on the oven
base.
 When cooking in the oven (EK 5731 W/GR
only), always leave the cooker lid open, in
order to avoid overheating.
The effects of dishes
on cooking results
Dishes and tins vary in their thickness,
conductivity, colour, etc. which affects the way
they transmit heat to the food inside them.
AAluminium, earthenware, oven glassware and
bright shiny utensils reduce cooking and
underneath browning.
BEnamelled cast iron, anodized aluminium,
aluminium with non-stick interior and coloured
exterior and dark, heavy utensils increase
cooking and underneath browning.
Condensation and steam
When food is heated it produces steam in the
same way as a boiling kettle. The oven vents
allow some of this steam to escape. However,
always stand back from t e oven w en
opening t e oven door to allow any build up of
steam or heat to release.
If the steam comes into contact with a cool
surface on the outside of the oven, e.g. a trim, it
will condense and produce water droplets. This
is quite normal and is not a fault with the oven.
To prevent discoloration, regularly wipe away
condensation and also soilage from surfaces.
Cookware
 Use any oven proof cookware which will
withstand temperatures of 25 °C.
 Baking trays, oven dishes, etc. should not be
placed directly against the grid covering the
fan at the back of the oven, or placed on the
oven base.
 Do not use baking trays larger than 3 cm x
35 cm (12 in x 14 in) as they will restrict the
circulation of heat and may affect performan-
ce.
Hints and Tips
Storage Drawer
The storage drawer is located underneath the
oven cavity.
During cooking the storage drawer may
become hot if the oven is on high for a long
period of time, therefore flammable
materials such as oven gloves, tea towels,
plastic aprons etc. should not be stored in
the drawer.
Oven accessories such as baking sheets,
will also become hot, therefore care
should be taken when removing these
items from the drawer whilst the oven is in
use or still hot.
4
3
2
1
All manuals and user guides at all-guides.com

9
Using the Conventional Oven
How to Use the
Conventional Oven
Turn the oven function control knob to the
required temperature.
THINGS TO NOTE
l The thermostat control light will remain on
until the correct temperature is reached. It will
then cycle on and off to show that temperatu-
re is being maintained.
Top oven element only
This function is suitable for finishing cooked
dishes, eg; lasagne, shepherds pie, cauliflower
cheese etc.
Bottom oven element only
This function is particularly useful when blind-
baking pastry or cooking pizza. It may also be
used to finish off quiches or flans to ensure the
base pastry is cooked through.
The middle shelf position allows for the best heat
distribution. To increase base browning simply
lower the shelf position. To increase top
browning, raise the shelf position.
The material and finish of the baking trays and
dishes used will affect base browning.
Enamelware, dark, heavy or non-stick utensils
increase base browning, while oven glassware,
shiny aluminium or polished steel trays reflect
the heat away and give less base browning.
Always place dishes centrally on the shelf to
ensure even browning.
Stand dishes on suitably sized baking trays to
prevent spillage onto the base of the oven and
make cleaning easier.
Do not place dishes, tins or baking trays directly
on the oven base as it becomes very hot and
damage will occur.
Single level cooking gives best results.
Hints and Tips
F
All manuals and user guides at all-guides.com

10
Food Temperature (°C) Runner Cooking
Positions Time (mins)
Biscuits - small cakes 16 -18 2 25-3
Bread, buns, yeast, doughs 2 -22 2 35-45
Casseroles 15 -17 1-2 9 -18
Queen Victoria sponge 17 -19 1-2 2 -3
Cakes - madeira, rich fruit 15 -17 2 9 -15
Choux pastry, eclairs 2 -22 2 3 -35
Fish 2 -22 2 2 -4
Fruit pies, plate tarts, crumbles 18 -2 2 5 -65
Meringues 9 -1 2 9 -15
Milk puddings 14 -16 2 9 -15
Pate, terrine (in baine-marie) 16 -18 1-2 6 -9
Pizzas 2 -23 1-2 25-3
Puff pastry, sausage rolls, vol-au-vents 2 -22 2 15-25
Quiches, flans 17 -2 1-2 5 -6
Scones 2 -22 2 8-15
Souffle 2 -22 2 35-45
Stuffed vegetables 2 -22 2 35-45
Roast meat & poultry 18 -2 2
Yorkshire pudding 2 -22 2 4 -5
Keep food warm, heat dishes 9 -1 2
Cooking Chart
see meat + poultry
roasting chart
Meat and Poultry Roasting Chart
Meat Cooking Time
Beef 2 -35 mins per 1/2kg (lb) + 20-35 mins
Beef, boned 25-35 mins per 1/2kg (lb) + 25-35 mins
Mutton and Lamb 25-35 mins per 1/2kg (lb) + 25-35 mins
Pork and Veal 3 -4 mins per 1/2kg (lb) + 30-40 mins
Ham 3 -4 mins per 1/2kg (lb) + 30-40 mins
Chicken 15-2 mins per 1/2kg (lb) + 20 mins
Turkey and Goose 15-2 mins per 1/2kg (lb) up to 3.5kg
(7.5lb) + 15 mins
Duck 25-35 mins per 1/2kg (lb) + 20 mins
When roasting, ensure the
meat is cooked thoroughly, use
a meat thermometer if preferred
to check the centre temperature
has reached the required tem-
perature (see table below).
MEAT TEMPERATURES
Beef Rare - 6 °C
Medium - 7 °C
Well Done - 8 °C
Pork Well Done - 8 °C
Lamb Medium - 7 °C
Well Done - 8 °C
These charts are intended as a guide only. It may be necessary to increase or decrease the temperatu-
re to suit your individual requirements. Only experience will enable you to determine the correct setting
for your personal requirements.
All manuals and user guides at all-guides.com

11
Grilling
Grilling must be carried out with the
oven door closed. he grill pan
handle must be removed from the
pan.
How to Use the Grill
1. Turn the oven control function knob to .
2. Adjust the grid and grill pan runner position to
allow for different thicknesses of food.
Position the food close to the element for
faster cooking and further away for more
gentle cooking.
Preheat the grill for a few minutes before
sealing steaks or toasting. Adjust the shelf as
necessary, during cooking.
- Most foods should be placed on the grid in the
grill pan to allow maximum circulation of air to
lift the food out of the fats and juices. Food
such as fish, liver and kidneys may be placed
directly on the grill pan, if preferred.
- Food should be thoroughly dried before
grilling to minimise splashing. Brush lean
meats and fish lightly with a little oil or melted
butter to keep them moist during cooking
- Accompaniments such as tomatoes and
mushrooms may be placed underneath the
grid when grilling meats
- When toasting bread, we suggest that the top
runner position is used.
- The food should be turned over during
cooking, as required.
Hints and Tips
Bacon rashers 2-3 each side
Beefburgers 6-1 each side
Chicken joints 1 -15 each side
Chops: 7-1 each side
1 -15 each side
Fish: 8-12 each side
4-6 each side
Kebabs 1 -15 each side
Kidneys: 4-6 each side
Liver: 5-1 each side
Sausages 1 -15 turn as required
Steaks: 3-6 each side
6-8 each side
7-1 each side
Browning only 3-5
Food Grill
Time (Min)
lamb
pork
whole trout/herring
illets plaice/cod
lamb/pig
lamb/pig
rare
medium
well
F
OI
L
All manuals and user guides at all-guides.com
all-guides.com

12
Before any maintenance or cleaning
can be carried out, you must
DISCONNEC the cooker from the
electricity supply.
The Ho Top
The hob is best cleaned whilst it is still warm, as
spillage can be removed more easily than if it is
left to cool.
Regularly wipe over the hob top using a soft cloth
well wrung out in warm water to which a little
wasing up liquid has been added. Avoid the use
of the following:
- household detergent and bleaches;
- impregnated pads unsuitable for non-stick
saucepans;
- steel wool pads;
- bath/sink stain removers.
Should the hob top become heavily soiled, it is
recommended that a cleaning product such as
Hob Brite or Bar Keepers Friend is used.
Pan Supports
The pan supports are dishwasher proof. If
washing them by hand, take care when drying
them as the enamelling process occasionally
leaves rough edges. If necessary, remove
stubborn stains using a paste cleaner.
The Burners
The burner caps and crowns can be removed for
cleaning.
Wash the burners caps and crowns using hot
soapy water, and remove marks with a mild
paste cleaner. A well moistened soap
impregnated steel wool pad can be used with
caution, if the marks are particularly difficult to
remove.
After cleaning, be sure to wipe dry with a soft
cloth.
Maintenance and Cleaning
All manuals and user guides at all-guides.com

13
The oven should be kept clean at all
times. A build-up of fats or other
foodstuffs could result in a fire,
especially in the grill pan.
Cleaning materials
Before using any cleaning materials on your
oven, check that they are suitable and that their
use is recommended by the manufacturer.
Cleaners that contain bleach should NOT be
used as they may dull the surface finishes.
Harsh abrasives should also be avoided.
External cleaning
Regularly wipe over the control panel, oven door
and door seal using a soft cloth well wrung out in
warm water to which a little washing up liquid
has been added.
To prevent damaging or weakening the door
glass panels avoid the use of the following:
 Household detergent and bleaches
 Impregnated pads unsuitable for
non-stick saucepans
 Brillo/Ajax pads or steel wool pads
 hemical oven pads or aerosols
 Rust removers
 Bath/Sink stain removers
Clean the outer and inner door glass using warm
soapy water. Should the inner door glass
become heavily soiled it is recommended that a
cleaning product such as Hob Brite, or Bar
Keepers Friend is used.
DO NOT clean the oven door while the
glass panels are warm. If this
precaution is not observed the glass
panel may shatter.
If the door glass panel becomes
chipped or has deep scratches, the
glass will be weakened and must be
replaced to prevent the possibility of the
panel shattering. ontact your local
Service entre who will be pleased to
advise further.
Oven S elves
To clean the oven shelves, soak in warm soapy
water and remove stubborn marks with a well
wetted soap impregnated pad. Rinse well and
dry with a soft cloth.
Cleaning the Oven
Oven Cavity
The enamelled oven cavity is best cleaned whilst
the oven is still warm.
Wipe the oven over with a soft cloth soaked in
warm soapy water after each use. From time to
time it will be necessary to do a more thorough
cleaning, using a proprietary oven cleaner.
Oven lamp replacement
Disconnect the appliance.
Unscrew the lamp and substitute it with another
suitable for higher temperature (3 °C) having
the following characteristics:
Voltage: 23 -24 V (5 Hz)
Power: 15W
Connection: E14
Lid cleaning (EK 5731 W/GR only)
The cooker lid can be disassembled for easier
cleaning (see fig.). After cleaning, carefully
reposition the lid into its hinges.
FO 0424
FO 0418
All manuals and user guides at all-guides.com

14
Something ot Working
SYMPTOM
nThere is no spark when lighting the gas
nThe gas ring burns unevenly
n The oven does not come on
nThe oven light does not come on
nIt takes too long to finish the dishes, or they
are cooked too fast.
nSteam and condensation settle on the food
and the oven cavity.
SOLUTION
uCheck that the unit is plugged in and the
electrical supply is switched on
uCheck that the RCCB has not tripped (if fitted)
uCheck the mains fuse has not blown
uCheck the burner cap and crown have been
replaced correctly, e.g. after cleaning.
uCheck the main jet is not blocked and the
burner crown is clear of food particles.
uCheck the burner cap and crown have been
replaced correctly, e.g. after cleaning.
uCheck a cooking function / temperature have
been selected.
uCheck the socket switch or the switch from
the mains supply to the oven is ON.
uCheck the light bulb, and replace it if
necessary (see "Oven Light Replacement")
uThe temperature may need adjusting
uRefer to the contents of this booklet,
especially to the chapter Using the Oven.
uLeave dishes inside the oven no longer than
15-2 minutes after the cooking is completed.
If after these checks, the appliance still does not
work, contact your local Service Force Centre.
When you contact the Service Centre, they will
need the following information:
1. Your name, address and post code.
2. Your telephone number
3. Clear and concise details of the fault
4. The model and the serial number (see rating
label)
5. Date of purchase
If the appliance is not working correctly, please carry out the following checks, before contacting your
local Electrolux Service Centre.
IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use
or installation, a charge will be made even if the appliance is under guarantee.
All manuals and user guides at all-guides.com

15
If you require spare parts or an engineer contact
your local Service Force Centre by telephoning:
87 5 929 929
Your call will be routed to the Service Centre
covering your post code area. The addresses of
Electrolux Service Force Centres are detailed on
the following pages.
CUSTOMER CARE
For general enquiries concerning your Electrolux
appliance and for further information on
Electrolux products, contact our Customer Care
Department by letter or telephone as follows:
Customer Care Department
Electrolux
55-77 High Street
Slough
Berkshire SL1 1DZ
Tel : [phone]
Guarantee Conditions
Service and Spare Parts
ELECTROLUX STANDARD GUARANTEE
CONDITIONS
We, Elec rolux, under ake ha if, wi hin 12 mon hs of
he da e of he purchase, his Elec rolux appliance or
any par hereof is proved o be defec ive by any
reason only of faul y workmanship or ma erials, we
will, a our op ion, repair or replace he same FREE
OF ANY CHARGE for labour, ma erials or carriage on
condi ion ha :
* The appliance has been correc ly ins alled and
used only on he gas and elec rici y supply s a ed
on he ra ing pla e.
* The appliance has been used for normal domes ic
purposes only, and in accordance wi h he
manufac urer's ins ruc ions.
* The appliance has no been serviced, main ained,
repaired, aken apar or ampered wi h by any
person no au horised by us.
* All service work under his guaran ee mus be
under aken by a Elec rolux Service Force Cen re.
* Any appliance or defec ive par replaced shall
become he Company's proper y.
* This guaran ee is in addi ion o your s a u ory and
o her legal righ s.
Home visi s are made be ween 8.30am and 5.30pm
Monday o Friday. Visi s may be available ou side
hese hours, in which case a premium will be
charged.
E clusions
This guarantee does not cover:
* Damage or calls resul ing from ranspor a ion,
improper use or neglec , he replacemen of any
ligh bulbs or removable par s of glass or plas ic.
* Cos s incurred for calls o pu righ an appliance
which is improperly ins alled or calls o appliance
ou side he Uni ed Kingdom.
* Appliances found o be in use wi hin a commercial
or similar environmen , plus hose which are he
subjec o ren al agreemen s.
* Produc s of Elec rolux manufac ure which are no
marke ed by Elec rolux.
European Guarantee
If you should move o ano her coun ry wi hin Europe
hen your guaran ee moves wi h you o your new home
subjec o he following qualifica ions:
* The guaran ee s ar s from he da e you firs
purchased your produc .
* The guaran ee is for he same period and o he
same ex en for labour and par s as exis in he
new con ry of use for his brand or range of
produc s.
* This guaran ee rela es o you and canno be
ransferred o ano her user.
* Your new home is wi hin he European Communi y
(EC) or European Free Trade Area.
* The produc is ins alled and used in accordance
wi h our ins ruc ions and is only used domes ically,
i.e. a normal household
The elec rical supply complies wi h he
specifica ion given in he ra ing label.
* The produc is ins alled aking in o accoun
regula ions in your new coun ry.
Before you move, please con ac your neares
Cus omer Care cen re, lis ed below, o give hem
de ails of your new home. They will hen ensure ha
he local Service Organisa ion is aware of your move
and able o look af er you and your appliances.
France Senlis [phone]
Germany Nürnberg [phone]
I aly Pordenone [phone]
Sweden S ockholm [phone]
UK Slough [phone]
All manuals and user guides at all-guides.com

16
ELECTROLUX SERVICE FORCE
To contact your local Electrolu Service Force Centre telephone [phone]
CHANNEL ISLANDS
GUERNSEY Guernsey Electricity
PO Box 4
Vale, Guernsey
Channel Islands
ERSEY ersey Electricity
Company
PO Box 45
Queens Road
St Helier
ersey
Channel Islands
E4 8NY
SCOTLAND
ABERDEEN 54 Claremont Street
(M05) Aberdeen
AB10 6RA
AUCHTERMUCHY 33A Burnside
(M03) Auchtermuchy
Fife
KY14 7A
BLANTYRE Unit 5
(M07) Block 2
Auchenraith Industrial
Estate
Rosendale Way
Blantyre
G72 0N
DUMFRIES 93 Irish Street
(M01) Dumfries
Scotland
DG1 2PQ
DUNOON Briar Hill
7 Hill Street
(M 67) Dunoon
Argyll
PA23 7AL
GLASGOW 20 Cunningham Road
(M04) Clyde Estate
Rutherglen,
Glasgow,
G73 1PP
INVERNESS Unit 3B
(M06) Smithton Indust. Est.
Smithton
Inverness
IV1 2PD
ISLE OF ARRAN Arran Domestics
(OWN SALES) Unit 4 The Douglas
Centre
Brodick
Isle of Arran
KA27 8A
ISLE OF BARRA Zerfah
(OWN SALES) 244 Bruernish
Isle of Barra
Western Islands
HS9 5QY
ISLE OF BUTE Walker Engineering
(M66) Glenmhor
Upper Serpentine
Road
Rothesay
Isle of Bute
PA20 9EH
NORTH EAST
GATESHEAD Unit 356a
(M39) Dukesway Court
Dukesway
Team Valley
Gateshead
NE11 0BH
GRIMSBY 15 Hainton Avenue
(M42) Grimsby
South Humberside
DN32 9AS
HULL Unit 1
(M41) Boulevard Industrial
Estate
Hull
HU3 4AY
LEEDS 64-66 Cross Gates
(M37) Road
Leeds
LS15 7NN
NEWTON AYCLIFFE Unit 16
(M45) Gurney Way
Aycliffe Ind Estate
Newton Aycliffe
DL5 6U
SHEFFIELD Pennine House
(M38) Roman Ridge Ind.
Roman Ridge Road
Sheffield
S9 1GB
NORTH WEST
BIRKENHEAD 1 Kelvin Park
(M11) Dock Road
Birkenhead
L41 1LT
CARLISLE Unit 7
(M10) ames Street
Workshops
ames Street
Carlisle
Cumbria CA2 5AH
ISLE OF MAN South Quay Ind.
(M64) Estate
Douglas
Isle of Man IM1 5AT
LIVERPOOL Unit 1
(M15) Honeys Green
Precinct
Honeys Green Lane
Liverpool
L12 9 H
MANCHESTER Unit B
(M09) Central Industrial
Estate
St Marks Street
Bolton
BL3 6NR
PRESTON Unit 250
(M13) Dawson Place
Walton Summit
Bamber Bridge
Preston
Lancashire
PR5 8AL
STOCKPORT Unit 20 Haigh Park
(M16) Haigh Avenue
Stockport
SK4 1QR
ISLE OF LEWIS ND Macleod
(M69) 16 ames Street
Stornoway
Isle of Lewis
PA872QW
KELSO 2-8 Wood Market
(M08) Kelso
Borders TD5 7AX
ORKNEY Corsie Domestics
(M65) 7 King Street
Kirkwall
Orkney KW15 1RE
PERTH Hydro Electrical
Inveralmond House
Ruthervenfield Road
Perth PH1 3AQ
PERTH Graham Begg Unit 4
(OWN SALES) Airport Ind Estate
Wick KW1 4QS
SHETLAND Tait Electronic
(OWN SALES) Systems Ltd.
Holmsgarth Road
Lerwick
Shetland ZE1 0PW
SHETLAND Bolts Shetland Ltd
(OWN SALES) 26 North Road
Lerwick
Shetland ZE1 0PE
WHALSAY Leask Electrical
Harlsdale
Symbister, Whalsay
(OWN SALES) Shetland ZE2 9AA
NORTHERN IRELAND
BELFAST Owenmore House
(M27) Kilwee Industrial
Estate
Upper Dunmury Lane
Belfast
BT17 0HD
WALES
CARDIFF Guardian Industrial
(M28) Estate
Clydesmuir Road
Tremorfa, Cardiff
CF2 2QS
CLYWD Unit 6-7 Coed - Parc
(M14) Abergele Road
Rhuddlan
Clwyd
Wales
LL18 5UG
OSWESTRY Plas Funnon
Warehouse
(M17) Middleton Road
Oswestry
SY11 2PP
HAVERFORDWEST Cromlech Lodge
(M75) Ambleston
Haverfordwest
Pembrokeshire
SA62 5DS
DYFED Maes Y Coed
(M77) High Mead
Llanybydder
Carmarthenshire
SA40 9UL
All manuals and user guides at all-guides.com
all-guides.com

17
ELECTROLUX SERVICE FORCE
To contact your local Electrolu Service Force Centre telephone [phone]
MIDLANDS
BIRMINGHAM 66 Birch Road East,
(M18) Wyrley Road
Industrial
Estate
Witton
Birmingham
B67DB
BOURNE Manning Road Ind
(M44) Estate
Pinfold Road
Bourne
PE10 9HT
BRIDGNORTH 65 St.Marys Street
(M72) Bridgnorth
Shropshire
WV16 4DR
GLOUCESTER 101 Rycroft Street
(M23) Gloucester
GL1 4NB
HEREFORD Unit 3
(M31) Bank Buildings
Cattle Market
Hereford
HE4 9HX
HIGHAM FERRERS 30 High Street
(M51) Higham Ferrers
Northants
NN10 8BB
ILKESTON Unit 2
(M43) Furnace Road
Ilkeston
DE7 5EP
LEICESTER Unit 7
(M22) Oaks Industrial Estate
Coventry Road
Narborough
Leicestershire
LE0 5GF
LINCOLN Unit 8 Stonefield Park
(M40) Clifton Street
Lincoln
LN5 8AA
NEWCASTLE 18-21 Croft Road
UNDER LYME Brampton Industrial
(M12) Estate
Newcastle under
Lyme
Staffordshire
ST5 0TW
REDDITCH 13 Thornhill Road
(M20) North Moons Moat
Redditch
Worcestershire
B98 9ND
TAMWORTH Unit 3
(M19) Sterling Park
Claymore
Tamworth
B77 5DO
WORCESTER Unit 1&2
(M73) Northbrook Close
Gregorys Mill Ind
Estate
Worcester
WR3 8BP
LONDON & EAST ANGLIA
BECKENHAM 11a Gardener Ind
(M79) Estate
Kent House Lane
Beckenham
Kent BR3 1QZ
CHELMSFORD Hanbury Road
(M47) Widford Ind Estate
Chelmsford
Essex
CM12 3AE
COLINDALE Unit 14
(M53) Capital Park
Capital Way
Colindale
London NW9 0EQ
ELTHAM 194 Court Road
(M78) Mottingham - Eltham
London SE9 4EW
ENFIELD 284 Alma Road
(M49) Enfield
London
EN3 7BB
GRAVESEND Unit B4,
(M57) Imperial Business
Estate
Gravesend
Kent
DA11 0DL
HARPENDEN Unit 4
(M46) Riverside Estate
Coldharbour Lane
Harpenden
AL5 4UN
LETCHWORTH 16-17 Woodsite Ind
(M50) Est.
Works Road
Letchworth
Herts
SG6 1LA
LONDON 2/4 Royal Lane
(M76) Yiewsley
West Drayton
Middlesex
UB7 8DL
MAIDENHEAD Reform Road
(M60) Maidenhead -
Berkshire
SL6 8BY
MOLESEY 10 Island Farm
(M61) Avenue
West Molesey
Surrey
KT8 2UZ
NEWBURY 9 Pipers Court
(M24) Berkshire Drive
Thatcham
Berkshire
RG19 4ER
IPSWICH Unit 6C
(M48) Elton Park Business
Centre
Hadleigh Road
Ipswich
IP2 0DD
NORWICH 2b Trafalgar Street
(M52) Norwich
NR1 3HN
SUNBURY Unit 1a
(M63) The Summit
Hanworth Road
Hanworth Ind Estate
Sunbury on Thames
TW16 5D
SOUTH EAST
ASHFORD Unit 2
(M58) Bridge Road
Business
Estate
Bridge Road
Ashford
Kent
TN2 1BB
FLEET Unit 1
(M59) Redfields Industrial
Estate
Church Crookham
Fleet
Hampshire
GU13 0RD
HAYWARDS HEATH 21-25 Bridge Road
(M55) Haywards Heath
Sussex
RH16 1UA
SOUTH WEST
BARNSTAPLE Main Road
(M30) Fremington
Barnstaple
North Devon
EX31 2NT
BOURNEMOUTH 63-65 Curzon Road
(M26) Bournemouth
Dorset
BH1 4PW
BRIDGEWATER 6 Hamp Industrial
(M35) Estate
Bridgewater
Somerset
BRISTOL 11 Eldon Way
(M25) Eldonwall Trading
Bristol
Avon
BS4 3QQ
EMSWORTH 266 Main Road
(M33) Southboure
Emsworth
PO10 8 L
ISLE OF WIGHT Unit 8
(M34) Enterprise Court
Ryde Business Park
Ryde
Isle of Wight
PO33 1DB
NEWTON ABBOT Unit 2
(M29) Zealley Industrial
Estate
Kingsteignton
Newton Abbot
S. Devon
TQ12 3TD
PLYMOUTH 16 Faraday Mill
(M32) Cattledown
Plymouth
PL4 0ST
REDRUTH Unit 7D Pool Industrial
(M36) Estate
Wilson Way, Redruth,
Cornwall
TR15 3QW
All manuals and user guides at all-guides.com

18
Important Safety Requirements
This appliance must be installed in accordance
with the Gas Safety (Installation and Use)
Regulations (current addition) and the I.E.E.
Wiring Regulations. Detailed recommendations
are contained in the following British Standard
Codes of Practice - B.S. 6172, B.S. 544 : Part 2
and B.S. 6891: Current Editions.
Provision for Ventilation
The room containing the cooker should have an
air supply in accordance with B.S. 544 : Part 2:
Current Editions.
The following requirements for ventilation must
be met.
The cooker should not be installed in a bed
sitting room with a volume of less than 2 m3, if it
is installed in a room of volume less 5m3 an air
vent of effective area of 11 cm2 is required; if it
is installed in a room of volume between 5m3
and 1 m3, an air vent of effective area 5 cm2 is
required, while if the volume exceeds 11m3 no
air vent is required. However, if the room has a
door which opens directly to the outside, no air
vent is required even when the volume is
between 5m3 and 11m3.
If there are other fuel burning appliances in the
same room, B.S. 544 : Part. 2: Current Editions
should be consulted to determine the requisite
air vent requirements.
Model Number: EK 5731
Appliance Class 2 sub class 1 and Class 1
APPLIANCE CATEGORY
:II 2H3+
APPLIANCE GAS SUPPLY: Natural gas G2
2 mbar
Dimensions
Height 9 mm
Depth 6 mm
Width 499 mm
Oven Capacity 1.7 Cu. ft
Technical Data
Instructions for the Installer
Ho
Rear left burner (rapid) 3, W
Front left burner (semi-rapid) 2, W
Rear right burner (semi-rapid) 2, W
Front right burner (auxiliary) 1, W
Oven
Top heating element 1, 44 W
Bottom heating element 1,252 W
Grill Element 1,879 W
Oven light 15 W
Total rating 2,311 W
Supply voltage (5 Hz) 23 -24 V
Location
The cooker may be located in a kitchen, a
kitchen/diner or bedsitting room but not in a
bathroom, shower room or garage.
For information regarding the fitting of flexible
supply pipes, the highest temperature at the rear
of this cooker which may come into contact with
the supply pipe is 7 °C above ambient.
When the appliance has been installed there
must be enough space fot the hotplate lid (when
present) to open fully.
Positioning the Cooker
Caution:
Some soft or badly fitted floor coverings can be
damaged when the cooker is moved across
their surface for cleaning. It is advisable to
ensure that the floor covering in the area below
the cooker is either securely fixed so as not to
ruck up when the cooker is moved or, if
preferred, removed.
All manuals and user guides at all-guides.com

19
BURNER RAPID SEMI-RAPID AUXILIARY
(large) (medium) (small)
POSITION MAX MIN MAX MIN MAX MIN
NOMINAL THERMAL
POWER kW 3.0 0.65 2.0 0.45 1.0 0.33
NOMINAL FLOW
RATE m
3
/h0.286 0.057 0.190 0.038 0.095 0.028
NOZZLE REFERENCE 11 9 Adjust. 96 Adjust. 70 Adjust.
NOMINAL THERMAL
POWER kW 2.8 0.65 2.0 0.45 1.0 0.33
NOMINAL FLOW
RATE g/h 202 43.5 144 29 72 21,5
NOZZLE REFERENCE 8 6 4 0 7 1 3 2 5 0 2 8
NATURAL GAS
0 mbar
TYPE OF
GAS
CHARACTERISTICS
LPG GAS
8-30/37 mbar
1/100 mm
1/100 mm
VALUE = 49.92 M /Kg
VALUE = 37.78 M /m
3
Ws - 50.7 M / m
3
115
780
420
A
B
C
D
E
Installation
Fig. 1
1. Positioning the Appliance (Fig. 1)
Note A:
The appliance is designed to be flush fitted with
2mm clearance at each side to allow for it to be
pulled forward for cleaning etc.
Note B:
The hotplate side trims should be flush with the
cabinets and must not be below. Adjustable
levelling feet at the front and rear are provided on
the base of the appliance. Adjustment is
obtained by rotating in or out, the feet at the front
or rear of the appliance from the underside of
the appliance, with the drawer removed.
A spirit level should be placed on a cake tray on
one of the shelves to confirm that the appliance
is correctly levelled.
The levelling feet fitted to the appliance will
achieve a height to hotplate trims of 9 mm- +
1 .
Note C:
If the appliance is fitted next to a side wall or
cabinets above height of the hotplate trims, then
a gap of 115 mm is required.
Curtains must not be fitted immediately behind
the cooker or within 115 mm of the sides of the
cooker.
Note D:
Any wall cabinet or extractor must not be lower
than 78 mm above hotplate level.
Note E:
Wall cabinets may be fitted in line with the sides
of the base units, providing that the lower edge
of the wall cabinet is a minimum of 42 mm
above the worktop.
The appliance must be installed in accordance
to the type X (standard EN 6 335-2-6).
Therefore the appliance can not be installed
beside furniture higher than the cooker worktop.
This cooker must only be installed by qualified
personnel, according to the manufacturers
instructions and to the relevant British
Standards.
FO 1141
Dimensions are given in millimeters
All manuals and user guides at all-guides.com

20
LEVELLING FEET
PENCIL LINE ON THE FLOOR
PLAN VIEW OF THE COOKER
480 mm.
100 mm.
300 mm.
245 mm.
WALL FACE
A
BACK OF COOKER
SIDE VIEW
OF THE COOKER
BASE OF COOKER
ENGAGEMENT EDGE FOR
STABILITY BRACKET
Fig. 3
Fitting the Sta ility Bracket
(Not supplied)
If the cooker has to be installed with a flexible
supply pipe, it is necessary that a stability device
is fitted.
(See safety Requirements: Page 2 ).
If a stability bracket is to be fitted by the installer,
these instructions should be read in conjunction
with the leaflet packed with the stability bracket.
Place cooker in its intended position and level
cooker.
Mark off 25 mm (11 1/2") from the right hand
side of the cooker as shown, this is the centre
line of the bracket fixing.
Draw a line 1 mm (4") from the front edge of
the levelling feet (see Fig. 2) and remove cooker
from its position. Mark off 48 mm (19") back
from this line on the centre line of the bracket to
locate the front edge of the lower bracket.
Fix lower bracket (with two fixing holes) to the
floor, then measure height from floor level to
engagement edge on back of cooker, dimension
'A' of Fig. 2.
Assemble upper bracket to lower bracket so that
underside of bracket is dimension 'A' +3mm (1/
8") above floor level. Re-position cooker and
check that top bracket engages into cooker back
to a depth of 75mm (3"), as shown in Fig. 2.
Should the stability bracket currently installed not
allow the cooker to stand correctly, ask the
installer to replace it with the correct type.
Fig. 2
Connecting to Gas
This cooker is designed to be installed with an
appliance flexible connection. Connection is
made to the RC 1/2 (1/2" B.S.P.) threaded entry
pipe located just below the hotplate level on the
rear right-hand side of the cooker. Check for gas
soundness after connecting the gas supply.
The gas bayonet connector must be fitted in the
shaded area indicated in the diagram. Take into
account that it must be possible to pull the
cooker forward sufficiently. The hose must not
get caught on the stability bracket.
Note:
For certain types of gas bayonet connection
used, it may not be possible for the appliance to
be pushed fully back to the wall stops.
Important:
Flexible tubing MUST comply with BS.669
Current Edition.
FO 2434
FO 2435
600
450
130
Dimensions are given in millimeters
Dimensions are given in millimeters
50 mm.
All manuals and user guides at all-guides.com