Electrolux E15IM60EBS0 User manual

Use Care Guide
Gu_a de Uso y Cuidado
Guide d'utilJsation et d'entretien

Thank you for choosing EJectrolux, the new premium brand in home appliances.
This Use & Care Guide is part of our commitment to customer satisfaction and
product quality throughout the service life of your new ice maker.
We view your purchase as the beginning of a relationship. To ensure our ability to
continue serving you, please use this page to record key product information.
Once you have your unit installed, we suggest you keep this manual in a safe
place for future reference. Should any problems occur, refer to the
Troubleshooting section of this manual. This information will help you quickly
identify a problem and get it remedied. In the event you require assistance, please
contact the dealer where you purchased your unit.
MAKEA RECORDFOR@UCKREFERENCE
[] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] []
Whenever you call to request information or service, you will need to know your
model number and serial number. You can find this information on the serial plate
located on the inside wall of your unit and on the product registration card.
@2004 EJectrolux Home Products, Inc.
Post Office Box 212378, Augusta, Georgia 30917, USA
All rights reserved. Printed in the USA

information
IPBODU BEG S ATION6£
[] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] []
The package containing this manual also includes your product registration
information. Warranty coverage begins at the time your Ebctrolux ice maker was
purchased.
Phase record the purchase date of your Electrolux unit and your dealer's name,
address and tebphone number.
Purchase Date
Eiectrolux Model Number
Electrolux Serial Number
Dealer Name
Dealer Address
Dealer Telephone
Keep this manual and the sales receipt together in a safe place for further
refe re nce.
[] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] []
For tolPfree telephone support in the U.S. and Canada:
1-877- 4ELECTROLUX (1-877-435-3287)
For online support and lnternet product information:
www.eleetroluxusa.eorn

TABLEOIF'CONN
[] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] []
Finding Information ...........................................2
PleaseReadAndSaveThisGuide...................2
MakeARecordForQuickReference................2
WarrantyRegistrationCard...............................3
Questions?........................................................3
TableOfContents..............................................4
Safety ...................................................................5
ImportantSafetyInstructions..............................5
Installation ..........................................................7
InstallationDimensions.......................................7
Draininstallation................................................8
Drain PumpConnection...................................10
Site Preparation.................................................11
Water Supply Connection ...............................13
Leveling .............................................................15
Door Reversal....................................................16
DoorAdjustment ...............................................18
Built-in Installation ..........................................20
Start-up ..............................................................21
NormalOperation..............................................22
iceCubeThickness.........................................22
iceDispsenserOperationandCare ................23
Maintenance......................................................25
SpecialConsiderations....................................25
MaintainingandCleaning................................25
ExteriorCleaning............................................25
StainlessSteelModels.....................................25
InteriorCleaning..............................................26
CondenserCleaning.......................................27
SelfCleaning...................................................28
InletScreenCleaning......................................29
Storage, Vacation and Moving ........................30
Troubleshooting ...............................................31
ifServiceIsRequired......................................32
Warranty Information .......................................33

IIM £NT S£F Y IINS U _ONS
[] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] []
Safety Precautions
Do not attempt to install or operate your unit until you have read the safety
precautions in this manual. Safety items throughout this manual are labeled with a
Danger, Warning or Caution based on the risk type.
Definitions
A This is the safety alert symbol. It is used to alert you to potential personal injury
hazards. Obey all safety messages that follow this symbol to avoid possible injury
or death.

GeneramPrecautions

IINSTAII,,,,,,,,,,_,,,,,,,,,,AT_OND_MENS_ONS
[] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] []
34 =!/8"
(86.7)
FULL
RETRACT
HEIGHT
WATER
OUTLET
WATER
DRAIN
Figure 1
(81)
WATER
VALVE "_o
21 =3/4"
(55.2) v

THE£1N
[] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] []
Model E151M60E can be installed using a gravity drain or can use a factory installed
or equivalent drain pump.
Follow these guidelines when installing drain lines to prevent water from flowing
back into the ice maker storage bin and/or potentially flowing onto the floor causing
water damage:
GravityDrain
• Drain lines must have a 5/8 inch inside diameter.
• Drain lines must have a 1 inch drop per 48 inches of run (1/4 inch per foot) and
must not create traps.
• The floor drain must be large enough to accommodate drainage from all
drains.
• Insulate the bin drain line to prevent condensation.
raceMakersWith Factory mnstaHedDrain Pump

1 Make certain the unit is not plugged into an electrical
outlet.
2 Carefully push the power cord grommet through the hole
in the back panel. See Figure 2.
3 Remove 12 screws and back panel.
4 Check that the clamps and hose connections are tight at
the following areas illustrated in Figure 3:
Discharge tube (A)
,, Drain tube (B)
,, Vent tube (C)
5 Place a suitable container beneath the pump's discharge
tube. (Container must be able to hold a
minimum of one gallon of water.)
BACK VIEW
Figure 3
GROMMET
Figure 2
SDE ViEW
UL184_2
BACK
PANEL
DRAIN
FiTTiNG
POWER
CORD
UL184=1
Plug the ice maker power cord into a properly grounded, polarized electrical
outlet.
Verify pump operation by pouring one gallon of water into the ice storage bin
of the ice maker. The pump should energize and pump the water into the
container.
8 At this time, verify that all tube and clamp connections are tight and leak free.
9 Unplug unit power cord from electrical outlet.
10 Reinstall back panel.
11 Continue to the next step in the installation process, Site Preparation.

CONNE £ DR£11NPUMP
[] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] []
If a gravity drain connection is not availabb, and you have not purchased the
E15JM60E with factory installed pump, we strongly recommend the use of the
Eiectrolux EJMP60 drain pump. The Eiectrolux EIMP60 drain pump is available
through your Dealer, or direct from Ebctrolux with compbte installation instructions.
If a pump other than the Ebctrolux EIMP60 drain pump is to be used, it must meet
the following specifications:
• It must be UL listed and have a UL listed, 120 VAC, 3-wire grounded power
cord.
• It must have overall maximum outside dimensions of 8-3/4" wide x 5-3/4"
deep x 7-3/4" high.
• It must have a minimum flow rate of 15 gallons per hour at 10 feet of lift.
• It must have a sealed sump which does not allow water leakage in the case
of a power outage, restricted drain or pump failure.
• It must have a check valve in the discharge line to prevent waste water return
to the pump.
• It must have an overflow protection control which will shut off power to the ice
maker in the event of a pump failure.
° It must have an operating temperature range of 50°F to 110°F (10°C to 43°C).

IP PAB NGT SITE
[] [] [] [] m m [] [] [] [] m [] m [] [] [] [] m m m m []
1 Position the unit on a flat, level surface, capable of supporting the entire
weight of the unit. Remember that the unit will be significantly heavier once it
is fully loaded.
2 The surrounding air temperature must be at least 50°F (10°C) but must not
exceed 110°F (43°C).
3 The unit must not be located near heat-generating equipment or in direct
sunlight.
4
5
6
The unit must be located to allow clearance for water, drain and electrical
connections in the rear of the ice maker.
Connect the unit to a grounded and polarized 115 VAC, 60 Hz, 15 A circuit
(normal household current).
Avoid connecting the unit to a Ground Fault Interruptor (GFI). GFIs are prone to
nuisance tripping which will cause the unit to shut down. GFIs are generally not
used on circuits which power equipment that must run unattended for long
periods of time.
The unit must be installed according to your local codes and ordinances.

Figure4
0"
CLEARANCE
NEEDED
UL124A
6 Install and connect the water supply line. See
Connecting the Water Supply for installation
requirements.
7 Position the unit to allow free air flow through the
front grille (see Figure 6).
8 Wipe out inside of unit with a damp cloth.
WALL
2 * 3/4"
CLEARANCE
NEEDED
Figure 5
EXHAUST Figure 6 _NTAKE

Whenconnectingthewatersupply,followtheseguidelines:
ReviewthebcaUplumbingcodesbeforeyouinstaUltheunit.
Thewaterpressureshouldbe between20 and120psi.
MakecertainaSHUT-OFFVALVEis
instaUledinthe1/4inchwatersupplyHne.
Connectsufficienttubingtotheunittoallow
theunitto bemovedforcleaningand
servicing.However,makecertainthatthe
tubingisnotpinchedordamagedduring
installation.
Ebctroluxrecommendstheuseof copper
tubingforinstallation.
WATER
CONNECTmON
ULI03 CO
Figure 7

Figure8
\
% . UL134
FFigure 9
POWER
WATER LiNE UL201
Figure 10
UL200
Locate the compression fitting and ferrule packed in the
unit. Slide the compression fitting and ferrule over the
1/4 inch water supply line. Do not use thread sealing
compound or tape. Using two wrenches, tighten the
compression fitting on the supply line (see Figure 8).
Carefully bend the water supply line into position and
connect the line to the solenoid valve (see Figure 9).
Avoid kinking the water supply line.
For recessed installations, allow extra water supply line
length to provide slack for easy removal from the
recessed area (see Figure 10). This will also safeguard
against kinking the line.
4 Plug in the power cord.
5 Gently push the unit into position. If desired the unit may
be recessed into cabinet or wall.
6 Allow at least 1-1/2 inches clearance behind the unit for
electrical, water supply and drain connections.

IILEV T UNiT
[] [] m m m m [] [] [] [] [] [] m [] [] [] [] m [] m m []
Use a ReveUto check the ReveUnessof the ice maker
from front to back and from side to side (see Figure
11).
tf the ice maker is not bveU, adjust the feet on the
corners of the unit as necessary (see Figure 12).
Check the bvelness after each adjustment and
repeat the previous steps until the unit is bveL
Figure 11
Figure 12

REVERSINGTHEBOOR(SOMEMO ILLS}
[] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] []
\
Figure 13
AH EbctroUux units may be bft or right hand opening. The door
opening is easily reversed by moving the hinge hard-ware to the
opposite side (see Figure 13).
To reverse the door:
1 Remove top hinge screw pin (7/64" AUUenwrench) from
cabinet (see Figure 14). Remove door by tilting forward
and Rifting off bottom hinge pin.
2 Remove pUastb screw plugs (3 top and 3 bottom) from
new hinge location (see Figure 15), and remove hinge pin
hole plug in top of door (see Figure 16). Do not discard.
J
Figure 14
SCREW
PLUGS
Figure 15 Figure 16

Remove top hinge (3 screws), reinstall hinge screw pin, and
remount on opposite side BOTTOM (see Figure 17).
Remove the two door cioser inserts from the existing bottom
hinge and instali as shown on the new bottom hinge (see
Figure 18).
Remove existing bottom hinge (3 screws) and remount on
opposite side TOP. Remove hinge screw pin.
With bottom of door facing up, remove pivot plate (2 screws),
flip over, and remount on opposite side of door (see Figure 19).
Holding door upright with top of door tiited forward, piace hole of
door pivot plate on bottom hinge screw pin (see Figure 20). Be
sure that the bosses on the closers align with holes in hinge
and hinge plate.
Tilt top of door into position in top hinge and instali top hinge
screw pin.
tn empty hinge holes, instali plastic screw plugs (3 top and 3
bottom) and door hole plug (1 ,door top) removed in step 2.
HINGE _"_
SCREW I I
PiN _=_
i
Figure 17
i
Figure 19
CLROO008

£DJUST NGTHEOB
[] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] []
Your door is aligned at the factory before shipment. OccasionaU re=adjustment may
be necessary, especially if an overlay paneU is installed. The following procedure
will correct for up to 1/4" alignment.
The door shouUd never be flush with the top of the cabinet. Even when bveU, the top
edge of the door wiIRbe 1/8" below the top of the cabinet (see Figure 21).
,_1/8"
t
Figure 21
Toadjust :
1 Compare the top edge of the door (opposite the
hinges) to the top edge of the cabinet and note the
type (up or down) of adjustment needed.
2 Remove the top hinge pivot pin with a 7/64" hex
wrench (see Figure 22) and lift door off bottom
hinge pin. Be careful not to lose door closers (see
Figure 24).
3 With door upside-down, loosen but do not remove
the two hinge plate screws.
Figure 22
f

4 tf door edge opposite the Nnges needs to
move up, move plate toward outside of
door. tf door edge needs to move down,
move plate toward inside of door (see
Figure 23). Repeat until top edge of door is
parallel with top of cabinet and tighten
screws securely.
5 After adjustment is complete, remove the
door closers from the bottom hinge, clean
thoroughly and apply petroleum jelly to the
mating surfaces of the closers (see
Figure 24). Be sure that bosses on closers
align with holes in Mnge and hinge plate.
Mount door and install top hinge pivot pin.
MOUNTING _ IS NOTCH
HOLES _
RAISE _LOWER
OUTSIDE OUTSIDE
DOOR EDGE DOOR EDGE
CLRCOOOla
DOOR
BOSS
Figure 24 UL3_2

£
[] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] []
Your Electrolux product has been designed for either free-standing or built4n
installation. When built=in, your ice maker does not require additional air space for
top, sides or rear. However, the front grille must NOT be obstructed.
Built-in Cabinet Dimensions
Unit Dimensions (see Figure 25)
Model Width Height Depth
E151M60E 14=15/16" 34-1/8" 24"