Electrolux ECS9081G User manual

ECS9081G
ECS6081G

9
10
11
9

Fig.4
5
600/900
420
360370-730
238
190
ECS9081G
ECS6081G
8
6
7
Upper chimney
Aluminum pipe
Mounting screws(ST 5X 50MM)
Drywall Anchors
Damper
set
8
9
10
1Duct fixing tape
1User manual
Fig.3
ECS9081G
ECS6081G
2
2.1
2.2
1
3
46
5
7
9
2.1
2.2 Lower chimney
Chimney mounting bracket
6
6
6
10

395mm
Min.830
Fig.5
(Fig.5)
Fig.6
450
400
600
600
180mm
280mm
153mm
Range hood
mounting points
Auxiliary mounting
points
12)
4.Using a 9mm drill bit, enlarge the pilot holes and insert the
plastic wall anchors (BB) into the wall along the line as
reference point. Insert screws and leave a 5mm(Fig.7) gap
between the wall and the back of the screw head to slide the
range hood into place. Ensure the screws and anchors (AA
and BB) are parallel with the horizontal line.
5
185mm
Fig.7
5.Hook the hood body(A) onto the screws( AA and BB)
mounted onto the wall and securely tighten the screws(
AA and BB) to secure the hood body(A) on the wall. Peel
off the backing and stick sponge strip to the front side
of the fan housing as shown(Fig.8)
Fig.8
6.Install two additional hood body mounting screws
(AA) into the auxiliary mounting holes to secure the
hood body (A) in place.
Main mounting holes
Auxiliary mounting holes
Fig.9
Fig.10
77
7Ducted mode

(Fig.11)
tape
Fig.11
8
the
(Fig.12)
9.
Fig.12
Glass
●Glass should be cleaned every week in order to keep
the shiny
Grease filter
Note: To replace the filter, please let the hood on
suction mode before cutting off the electrical supplier
and don't open the glass panel by hand.
●
●
●
●
●
●
●
●
The grease filter should be cleaned frequently (
every two months of operation, or more frequently for
heavy use). Use a warm detergent solution.
Grease filter is washable
Lift the glass to the height where the poles hold it.
Remove the grease filter by pulling out each latch
while the glass is open. This will disengage the filter
from the hood. Tilt the filter downward and remove.
Wash the filters, taking care not to bend them.
Allow them to be dry before refitting
When refitting the filters, make sure that the handle
is visible from the outside.
To install the grease filter, align rear filter tabs with
slots in the hood. Pull out the latch, push filter into
position and release. Make sure the filter is securely
engaged after assembly.
Push the glass to the original position.
Replacing the lamp
Replace the damaged LED, only use LED DC 12V,2X2W
Max
Note:
WARNING: .
1. Always switch off the electrical supply before carrying
out any operation on the appliance.
2. Only a qualified and trained service technician can
undertake the work of bulbs replacement and servicing.
We recommend only using lamps of the same
specification as the ones being replaced.
9
Changing the lamp

11
Philippines
Consumer Care Center Toll Free:
1-800-10-845-CARE(2273)
Consumer Care Hotline:(+63 2)845-CARE(2273)
Electrolux Philippines,lnc.
Unit B 12F Cyber Sigma Bldg, Lawton Avenue,
McKinley West,Taguig, Philippines 1634
Trunkline:[phone]
Website:www.electrolux.com.ph
Email:[e-mail]
Vietnam
Consumer Care Center Toll Free
1800-58-88-99
Tel: [phone]
Electrolux Vietnam Ltd.
Unit 1&2, 10F Sofic Tower, #10 Mai Chi Tho
Street,
Thu Thiem Ward, Thu Duc City, Ho Chi
Minh City, Vietnam