Electrolux EFC 9510 User manual

Libretto Istruzioni
Instruction Manual
Manuel d’Instructions
Bedienungsanleitung
Gebruiksaanwijzing
EFC 6510
EFC 9510
NL 38
DE 29
FR 20
GB 11
IT 2

11GB
CONTENTS
Dear Customer,
If you follow the recommendations
contained in this Instruction Manual,
your appliance will give you constant
high performance and will remain
efficient for many years to come.
RECOMMENDATIONS AND SUGGESTIONS 12
CHARACTERISTICS 13
INSTALLATION 14
USE 17
MAINTENANCE 18

12GB
RECOMMENDATIONS AND SUGGESTIONS
INSTALLATION
• The manufacturer will not be held liable for any damages resulting
from incorrect or improper installation.
• The minimum safety distance between the cooker top and the
extractor hood is 650 mm.
• Check that the mains voltage corresponds to that indicated on the
rating plate fixed to the inside of the hood.
• For Class I appliances, check that the domestic power supply
guarantees adequate earthing.
Connect the extractor to the exhaust flue through a pipe of
minimum diameter 120 mm. The route of the flue must be as short
as possible.
• Do not connect the extractor hood to exhaust ducts carrying
combustion fumes (boilers, fireplaces, etc.).
• Iftheextractorisusedinconjunctionwithnon-electricalappliances
(e.g. gas burning appliances), a sufficient degree of aeration must
be guaranteed in the room in order to prevent the backflow of
exhaust gas. The kitchen must have an opening communicating
directly with the open air in order to guarantee the entry of clean
air.
USE
• The extractor hood has been designed exclusively for domestic
use to eliminate kitchen smells.
• Never use the hood for purposes other than for which it has ben
designed.
• Never leave high naked flames under the hood when it is in
operation.
• Adjust the flame intensity to direct it onto the bottom of the pan
only, making sure that it does not engulf the sides.
• Deep fat fryers must be continuously monitored during use:
overheated oil can burst into flames.
• The hood should not be used by children or persons not instructed
in its correct use.
MAINTENANCE
• Switch off or unplug the appliance from the mains supply before
carrying out any maintenance work.
• Clean and/or replace the Filters after the specified time period.
• Clean the hood using a damp cloth and a neutral liquid detergent.
650 mm min.

13GB
2.1
2.2
2
1
9
14
8b 8a
12c
12a 7.2.1 1
1
11
12a
14.1
16
15
598 - 898
62 - 72 545
55
300
260
433
740
740 min
940 max
CHARACTERISTICS
Dimensions
Components
Thedescribedequipmentcouldchangeaccordingtothedifferentcountries.
Ref. Q.ty ProductComponents
11 Hood Body, complete with: Controls, Light,
Blower, Filters
21 Telescopic Chimney comprising:
2.1 1 Upper Section
2.2 1 Lower Section
8a 1 Right Air Outlet Grill
8b 1 Left Air Outlet Grill
91 Reducer Flange ø 150-120 mm
14 1 HoodBodyAirOutletExtensionPiececonsisting
of two Half Shells
14.1 2 Air Outlet Connection Extension
15 1 Air Outlet Connection
16 1 Air Outlet Deflector
Ref. Q.ty Installation Components
7.2.1 2 Upper Chimney Section Fixing Brackets
11 6 Wall Plugs
12a 6 Screws 4,2 x 44,4
12c 6 Screws 2,9 x 9,5
Q.ty Documentation
1 Instruction Manual

14GB
INSTALLATION
Wall drilling and bracket fixing
Wall marking:
• Draw a vertical line on the supporting wall up to the ceiling, or as high as practical, at the centre
of the area in which the hood will be installed.
• Draw a horizontal line at 650 mm above the hob.
• Place bracket 7.2.1 on the wall as shown about 1-2 mm from the ceiling or upper limit aligning
the centre (notch) with the vertical reference line.
• Mark the wall at the centres of the holes in the bracket.
• Place bracket 7.2.1 on the wall as shown at X mm below the first bracket (X = height of the upper
chimney section supplied), aligning the centre (notch) with the vertical line.
• Mark the wall at the centres of the holes in the bracket.
• Mark a reference point as indicated at 116 mm from the vertical reference line and 332 mm above
the horizontal reference line.
• Repeat this operation on the other side.
• Drill ø 8 mm holes at all the centre points marked.
• Insert the wall plugs 11 in the holes.
• Fix the brackets using the 12a screws (4,2 x 44,4) supplied.
• Insert the two screws 12a (4,2 x 44,4) supplied in the hood body fixing holes, leaving a gap of 5-
6 mm between the wall and the head of the screw.
11
12a
332 X
116
1
2
116
650 min.
7.2.1

15GB
Mounting the hood body
• Before attaching the hood body, tighten the two
screws Vr located on the hood body mounting
points.
• Hook the hood body onto the screws 12a
• Fully tighten support screws 12a
• Adjust screws Vr to level the hood body.
Connections
DUCTED VERSION AIR EXHAUST SYSTEM
When installing the ducted version, connect the hood to the chimney using either a flexible or rigid
pipe ø 150 or 120 mm, the choice of which is left to the installer.
• To install a ø 120 mm air exhaust connection,
insert the reducer flange 9on the hood body
outlet.
• Fix the pipe in position using sufficient pipe
clamps (not supplied).
• Remove any activated charcoal filters.
Lateral air exhaust on ducted version
(connection to exhaust flue above wall
cupboards)
• Assemble the half-shells of the hood body
extension piece 14.
• Push fit the assembled hood body extension 14
onto the air exhaust outlet.
• Insert the deflector 16into the air exhaust fitting
15 to close off the unused outlet.
• Push fit connection piece 15 to the hood body
extension piece 14, ensuring that the free end
matches up with the opening of the required
outlet duct.
• Remove any activated charcoal filters.
12a
Vr
9
ø 120ø 150
15
16
14

16GB
RECIRCULATION VERSION AIR OUTLET
• Assemble the two halves of the hood body
extension piece 14.
• Push fit the assembled hood body extension
piece 14 onto the air outlet.
• Push fit connection 15 onto the hood body
extension piece 14.
• Insert the connection extension pieces laterally
14.1 in connection 15.
• Makesure that the outlet of the extensionpieces
14.1 is horizontally and vertically aligned with
the chimney outlets. Ifthis is not thecase, adjust
the position by either reversing the connection
extension pieces 14.1 or by cutting the hood
body extension 14 along one of the thinner
section channels denoting the pre-fixed lengths,
then reassemble as described previously.
• The air outlet directional grills 8a - 8b must be
fitted after the lower outlet duct has been
installed.
• Ensure that the activated charcoal filters have
been inserted.
ELECTRICAL CONNECTION
• Connect the hood to the mains through a two-pole switch having a contact gap of at least 3 mm.
Flue assembly
Upper exhaust flue
• Slightly widen the two sides of the upper flue
and hook them behind the brackets 7.2.1,
making sure that they are well seated.
• Secure the sides to the brackets using the 4
screws 12c (2,9 x 9,5) supplied.
Lower exhaust flue
• Slightlywidenthetwosidesofthe flue and hook
them between the upper flue and the wall,
making sure that they are well seated.
• Fix the lower part laterally to the hood body
using the 2 screws 12c (2,9 x 9,5) supplied.
• On the recirculation version, fit the directional
grids8a – 8b in their housings making sure that
the directional symbols are towards the top and
front of the hood. Also make sure that they are
correctly inserted in the connection extension
pieces 14.1.
12c
14
14.115
8
a
8b
12
c
8a
2.1
2.2
28b
7.2.1
12
c

17GB
LM V3S1 S2V2V1
USE
Control panel
LLight Switches the lighting system on and off.
S1 Led Motor running led. Flashes when the grease filters are saturated.
S2 Led Intensivespeed led.Flasheswhentheactivatedcarbon odour filters are exhausted.
MMotor Switches the extractor motor on and off at low speed. Used to provide a contin-
uos and silent air change in the presence of light cooking vapours.
V1 Speed Reduces the operating speed.
V2 Speed Increases the operating speed.
V3 Intensive Maximum speed, used for eliminating the highest cooking vapour emission.
speed Switches off automatically after 10 minutes operation. Can also be switched off
manually by pressing the button.

18GB
MAINTENANCE
Grease filters
CLEANING METAL SELF- SUPPORTING GREASE FILTERS
Alarm signal reset
• Switch off the lights and extractor motor.
• Press button V2 for at least 3 seconds, until the
leds start to flash.
Cleaning the filters
• The filters are washable and must be cleaned
when led S1 flashes or at least every 2 months
of operation, or more frequently for particularly
heavy usage.
• Removethefiltersoneatatimebypushingthem
towards the back of the group and pulling down
at the same time.
• Wash the filters, taking care not to bend them.
Allow them to dry before refitting.
• When refitting the filters, make sure that the
handle is visible on the outside.

19GB
Activated charcoal filter (Recirculation version)
REPLACING THE ACTIVATED CHARCOAL FILTER
• The filter is not washable and cannot be
regenerated. It must be replaced when led S2
flashes or at least every 4 months. The alarm
signal will only light up when the extractor
motor is switched on.
Alarm signal reset
• Switch off the lights and extractor motor.
• Press button V2 for at least 3 seconds, until the
leds start to flash.
Replacing the Filter
• Remove the metal grease filters
• Remove the saturated activated carbon filter by
releasing the fixing hooks
• Fit the new filter by hooking it into its seating
• Replace the metal grease filters.
Alarm signal activation
• On the recirulcation version extractor hood, the
filter saturation alarm is activated during
installation or at a later date.
• Switch off the lights and extractor motor.
• Press button V2 for at least 10 seconds, until
the leds start to flash:
• 2 flashes of the activated carbon odour filter
saturation alarm led = filter ACTIVATED
• 1 flash of the activated carbon odour filter
saturation alarm led = filter DEACTIVATED
Lighting
LIGHT REPLACEMENT
• 20 W halogen light.
• Remove the 2 Screws fixing the Lighting
support, and pull it out of from the Hood.
• Extract the Lamp from the Support.
• Replace with another of the same type, making
sure that the two pins are properly inserted in
the lamp holder socket holes.
• Replace the Support, fixing it in place with the
two Screws removed as above.