Electrolux ICON RH30WC60GS User manual

Installation, Use & Care Guide
30” and 36” Free-Standing Range Hood
Guia de Instalación, Uso y Cuidado
30” y 36” Campana extractora
Guide d’installation, utilisation et d’entretien
30” et 36” Hotte aspirante
RH30WC60GS + RH36WC60GS316488522
OCT/10

22
22
2
Please read and save this guide
Thank you for choosing ElectrElectr
ElectrElectr
Electroluxolux
oluxolux
olux, the new premium brand in home appliances. This
Use & Care Guide
is
part of our commitment to customer satisfaction and product quality throughout the service life of your new
appliance.
We view your purchase as the beginning of a relationship. To ensure our ability to continue serving you,
please use this page to record important product information.
Keep a rKeep a r
Keep a rKeep a r
Keep a recorecor
ecorecor
ecord for quick rd for quick r
d for quick rd for quick r
d for quick referefer
eferefer
eferenceence
enceence
ence
Finding Information
Questions?
For toll-free telephone support in the U.S. and Canada:
(1-877-435-3287)(1-877-435-3287)
(1-877-435-3287)
Table of contents
Important Safety InstructionsImportant Safety Instructions
Important Safety InstructionsImportant Safety Instructions
Important Safety Instructions ..................................... 3-43-4
3-43-4
3-4
Electrical & Installation rElectrical & Installation r
Electrical & Installation rElectrical & Installation r
Electrical & Installation requirements ........................... 55
55
5
Electrical requirements ......................................................... 5
IMPORTANT............................................................................... 5
Before installing the hood .................................................. 5
List of MaterialsList of Materials
List of MaterialsList of Materials
List of Materials 66
66
6
Parts Included with your Hood ......................................... 6
Optional Accessories ........................................................... 6
Tools/Materials required ....................................................... 6
Installing the hoodInstalling the hood
Installing the hoodInstalling the hood
Installing the hood ........................................................ 7-147-14
7-147-14
Installing preparation............................................................ 7
Wall framing for adequate support ................................. 7
Removing the packaging ................................................... 7
Examples of possible ducting ............................................ 8
Ductwork installation guidelines ..................................... 8
Ductwork and wiring locations ........................................ 8
Mounting the duct cover bracket ................................... 9
Ceiling ducting...................................................................... 10
Wall ducting............................................................................ 10
House wiring location ........................................................ 10
Install framing for hood support .................................... 10
Mounting the hood ............................................................. 11
Connecting the ductwork ............................................... 12
Air deector installation
(Recirculating accessories) ................................................ 12
Making the electrical connections .................................. 13
Mounting the glass canopy ................................................ 13
Mounting the duct cover..................................................... 14
FeaturFeatur
FeaturFeatur
Featureses
eses
es .................................................................................. 1515
1515
15
ContrContr
ContrContr
Control buttonsol buttons
ol buttonsol buttons
ol buttons ................................................................... 1616
1616
16
Special functionsSpecial functions
Special functionsSpecial functions
Special functions ................................................................ 1717
1717
17
Clock programming ............................................................... 17
Grease lter saturationalarm ............................................... 17
Charcoal lter saturation alarm
(Recirculating acc essories) ................................................ 17
Audible signal activation and deactivation .................. 17
Charcoal lter inclusion and exclusion
(Recirculating accessories) .................................................. 17
Heat sensor............................................................................... 17
For Best results ........................................................................ 18
CarCar
CarCar
Car e and cleaninge and cleaning
e and cleaninge and cleaning
e and cleaning .............................................................. 1919
1919
19
Filters .......................................................................................... 19
Lights .......................................................................................... 19
Optional Charcoal Filters ..................................................... 20
Hood Surface .......................................................................... 20
WW
WW
Warranty Informationarranty Information
arranty Informationarranty Information
arranty Information ........................................................ 2121
2121
21
©2007 Electrolux Home Products, Inc. All rights reserved. Printed in Mexico
Purchase date
Model number
Serial number (see picture for location)
NOTE
Registering your product with Electrolux enhances
our ability to serve you. You can register online at
www.electroluxappliances.com by dropping your
Product Registration Card in the mail.
For online support and Internet product information visit http://www.electroluxappliances.com
.....................................................................

33
33
3
Important Safety Instructions
Important Safety Instructions
Read all instructions beforRead all instructions befor
Read all instructions beforRead all instructions befor
Read all instructions before using thise using this
e using thise using this
e using this
appliance.appliance.
appliance.appliance.
appliance.
Save these instructions for futurSave these instructions for futur
Save these instructions for futurSave these instructions for futur
Save these instructions for futuree
ee
e
rr
rr
referefer
eferefer
efer ence.ence.
ence.ence.
ence.
ApprAppr
ApprAppr
Appr oved for roved for r
oved for roved for r
oved for residential appliancesesidential appliances
esidential appliancesesidential appliances
esidential appliances
For rFor r
For rFor r
For r esidential use onlyesidential use only
esidential use onlyesidential use only
esidential use only
Do not attempt to install or operate your appliance
until you have read the safety precautions in this
manual. Safety items throughout this manual are
labeled with a WARNING or CAUTION based on the
risk type.
This symbol alerts you to
situations that may cause
serious body harm, death
or property damage.
This symbol alerts you to
situations that may cause
bodily injury or property
damage.
PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING.
INSTALLATION MUST COMPLY WITH ALL LOCAL CODES.
IMPORTANT: Save these Instructions for the Local Electrical Inspector’s use.
INSTALLER: Please leave these Instructions with this unit for the owner.
OWNER: Please retain these instructions for future reference.
Safety Warning: Turn o power circuit at service panel and lock out panel, before wiring this appliance.
Requirement: 120 V AC, 60 Hz. 15 or 20 A Branch Circuit

44
44
4Important safety Instructions
READ AND SAVE THESE INSTRUCTIONS
Automatically Operated Device - To Reduce The
Risk Of Injury Disconnect From Power Supply Before
Servicing.
This unit is equpeed with integral disconnecting switch
located inside the blower housing
TO REDUCE THE RISK OF A RANGE TOP GREASE
FIRE.
a) Never leave surface units unattended at high settings.
Boilovers cause smoking and greasy spillovers that may
ignite. Heat oils slowly on low or medium settings.
b) Always turn hood ON when cooking at high heat or
when ambeing food (I.e. Crepes Suzette, Cherries
Jubilee, Peppercorn Beef Flambe’).
c) Clean ventilating fans frequently. Grease should not
be allowed to accumulate on fan or lter.
d) Use proper pan size. Always use cookware appropri-
ate for the size of the surface element.
TO REDUCE THE RISK OF INJURY TO PERSONS, IN
THE EVENT OF A RANGE TOP GREASE FIRE, OB-
SERVE THE FOLLOWING:
a) SMOTHER FLAMES with a close-tting lid, cookie
sheet, or other metal tray, then turn o the gas burner
or the electric element. BE CAREFUL TO PREVENT
BURNS. If the ames do not go out immediately,
EVACUATE AND CALLTHE FIRE DEPARTMENT.
b) NEVER PICK UP A FLAMING PAN - you may be
burned.
c) DO NOT USEWATER, including wet dishcloths or tow-
els - a violent steam explosion will result.
d) Use an extinguisher ONLY if:
1) You know you have a class ABC extinguisher, and
you already know how to operate it.
2) The re is small and contained in the area where it
started.
3) The re department is being called.
4) You can ght the re with your back to an exit.
OPERATION
a. Always leave safety grills and lters in place. Without
these components, operating blowers could catch onto hair,
ngers and loose clothing.
The manufacturer declines all responsibility in the event
of failure to observe the instructions given here for instal-
lation, maintenance and suitable use of the product. The
manufacturer further declines all responsibility for injury
due to negligence and the warranty of the unit automati-
cally expires due to improper maintenance.
Important safety Instructions
FOR GENERALVENTILATING USE ONLY. DO NOT USE
TO EXHAUST HAZARDOUS OR EXPLOSIVE MATERI-
ALS OR VAPORS.
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,
OR INJURY TO PERSONS, OBSERVE THE FOL-
LOWING:
A. Use this unit only in the manner intended by the manu-
facturer. If you have questions, contact the manufac-
turer.
B. Before servicing or cleaning the unit, switch power o
at service panel and lock service panel disconnecting
means to prevent power from being switched on acci-
dentally. When the service disconnecting means can-
not be locked, securely fasten a prominent warning
device, such as a tag, to the service panel.
C. Installation Work and Electrical Wiring Must Be Done
By Qualied Person(s) In Accordance With All Appli-
cable Codes & Standards, Including Fire-rated Con-
struction.
D. Sucient air is needed for proper combustion and ex-
hausting of gases through the ue (Chimney) of fuel
burning equipment to prevent back- drafting. Follow
the heating equipment manufacturers guideline and
safety standards such as those published by the Na-
tional Fire Protection Association (NFPA), the Ameri-
can Society for Heating, Refrigeration and Air Condi-
tioning Engineers (ASHRAE), and the local code au-
thorities.
E. When cutting or drilling into wall or ceiling, do not dam-
age electrical wiring and other hidden utilities.
F. Ducted systems must always be vented to the outdoors.
To reduce risk of re and to properly exhaust air, be
sure to duct air outside - do not vent exhaust air into
spaces within walls, ceilings, attics, crawl spaces, or
garages.
TO REDUCE THE RISK OF FIRE, USE ONLY METAL
DUCT WORK.
Install this hood in accordance with all requirements speci-
ed.
To Reduce The Risk Of Fire Or Electric Shock, Do Not
Use This Hood With Any External Solid State Speed
Control Device.

55
55
5
Important safety Instructions - Electrical & Installation
requirements
Electrical & Installation requirements
READ AND SAVE THESE INSTRUCTIONS
Electrical rElectrical r
Electrical rElectrical r
Electrical requirequir
equirequir
equirementsements
ementsements
ements
IMPORIMPOR
IMPORIMPOR
IMPORTT
TT
TANTANT
ANTANT
ANT
Observe all governing codes and ordinances.
It is the customer’s responsibility:
To contact a qualied electrical installer.
To assure that the electrical installation is adequate
and in conformance with National Electrical Code,
ANSI/NFPA 70 — latest edition*, or CSA Standards
C22.1-94, Canadian Electrical Code, Part 1 and
C22.2 No.0-M91 - latest edition** and all local codes
and ordinances.
If codes permit and a separate ground wire is used, it
is recommended that a qualied electrician determine
that the ground path is adequate.
Do not ground to a gas pipe.
Check with a qualied electrician if you are not sure
range hood is properly grounded.
Do not have a fuse in the neutral or ground circuit.
IMPORIMPOR
IMPORIMPOR
IMPORTT
TT
TANTANT
ANTANT
ANT
Save Installation Instructions for electrical inspector’s
use.
The range hood must be connected with copper wire
only.
The range hood should be connected directly to the
fused disconnect (Or circuit breaker) box through
metal electrical conduit.
Wire sizes must conform to the requirements of the
National Electrical Code ANSI/NFPA 70 — latest edi-
tion*, or CSA Standards C22.1-94, Canadian Electri-
cal Code Part 1 and C22.2 No. 0-M91 - latest edi-
tion** and all local codes and ordinances.
A U.L.- or C.S.A.-listed conduit connector must be
provided at each end of the power supply conduit (at
the range hood and at the junction box).
Copies of the standards listed may be obtained from:
* National Fire Protection Association Batterymarch Park Quincy,
Massachusetts 02269
** CSA International 8501 East Pleasant Valley Road Cleve-
land, Ohio 44131-5575
Before installing the hood
1.1.
1.1.
1. For the most ecient air ow exhaust, use a
straight run or as few elbows as possible.
Vent unit to outside of building and recirculating.
2.2.
2.2.
2. At least two people are necessary for installation.
3.3.
3.3.
3. The hood is tted with Screws and Drywall
Anchors suitable for most surfaces, consult a
Qualied Installer, check if they perfectly t with
your cabinet/wall.
4.4.
4.4.
4. Do not use ex ducting.
5.5.
5.5.
5. COLD WEATHER installations should have an
additional backdraft damper that is already installed
to minimize backward cold air ow and a nonmetallic
thermal break to minimize conduction of outside
temperatures as part of the ductwork. The
damper should be on the cold air side of the
thermal break.
The break should be as close as possible to
where the ducting enters the heated portion of
the house.
6.6.
6.6.
6. Make up air: Local building codes may require the
use of Make-Up Air Systems when using Ducted
Ventilation Systems greater than specied CFM of
air movement.
The specied CFM varies from locale to locale.
Consult your HVAC professional for specic
requirements in your area.

66
66
6
List of Materials
Parts Included with your HoodParts Included with your Hood
Parts Included with your HoodParts Included with your Hood
Parts Included with your Hood
tHood canopy assembly with blower, transition.
tLamp already installed.
tGrease lter.
tGlass Canopy
tDuct cover.
tHardware bag with:
tPlastic Gasket.
tTemplate.
tTop duct cover wall support bracket (1 piece)
tUse, care and installation guide
tGlass bracket (2 pieces)
tWood screws (6 pieces - 3/16" x 1" 3/4)
tHood attachment anchors screws (6 pieces -
1/8" x 3/8")
tAssembly screws (8 pieces)
Optional accessoriesOptional accessories
Optional accessoriesOptional accessories
Optional accessories
tRe circulation KIT
tCharcoal lter
TT
TT
Tools/Materials rools/Materials r
ools/Materials rools/Materials r
ools/Materials requirequir
equirequir
equireded
eded
ed
tDuct tape
tWire nuts
tTape to mount template
t8" rounded metal duct length to suit installation
tGloves to protect against sharp edges
tSafety glasses
tHammer
tElectric drill with 5/16" bit
tPliers
tMeasuring tape
tSaw, jig saw
tLevel
tKnife
tWire cutter
tPhillips (Pozidrive) # 2 screwdriver
tTorx # 2 screwdriver
List of Materials
tBottom
tTop
tGrease lter replacement

77
77
7
Installing the hood
Installing the hood
tttttFor the most ecient air ow exhaust, use a
straight run or as few elbows as possible.
Vent unit to outside of building and recirculating.
tttttOn avarage 2 to 3 hours are necessary to com-
plete installation (without considering cut to be
done on wall and or on cabinet, installation of
ducts , conduit and electrical connections to the
mains).
tttttThe hood is tted with Screws and Drywall
Anchors suitable for most surfaces, consult a
Qualied Installer, check if they perfectly t with
your cabinet/wall.
tttttDo not use ex ducting.
tttttCOLD WEATHER installations should have an
additional backdraft damper that is already installed
to minimize backward cold air ow and a nonmetallic
thermal break to minimize conduction of outside
temperatures as part of the ductwork. The
damper should be on the cold air side of the
thermal break.
The break should be as close as possible to
where the ducting enters the heated portion of
the house.
tttttMake up air: Local building codes may require the
use of Make-Up Air Systems when using Ducted
Ventilation Systems greater than specied CFM of
air movement.
The specied CFM varies from locale to locale.
Consult your HVAC professional for specic
requirements in your area.
tttttTT
TT
Typical installationypical installation
ypical installationypical installation
ypical installation
Min installation height from the range top to the
bottom of the hood is 30" if a gas range is used
or 24" to 30" if an electric range is used.
These hoods arThese hoods ar
These hoods arThese hoods ar
These hoods ar e not re not r
e not re not r
e not recommended to be usedecommended to be used
ecommended to be usedecommended to be used
ecommended to be used
over indoor grills.over indoor grills.
over indoor grills.over indoor grills.
over indoor grills.
The hood may be installed onto a wall and vented to
the outdoors, or it can be installed for recirculating
operation (recirculating accessories not supplied with
the hood).
This hood can be installed over any electric and gas
cooktop/range.
It can not be installed over any prIt can not be installed over any pr
It can not be installed over any prIt can not be installed over any pr
It can not be installed over any pr ofessionalofessional
ofessionalofessional
ofessional
cooktop / range.cooktop / range.
cooktop / range.cooktop / range.
cooktop / range.
Installing prInstalling pr
Installing prInstalling pr
Installing preparationeparation
eparationeparation
eparation
Advance planningAdvance planning
Advance planningAdvance planning
Advance planning
tDetermine the exact location of the vent hood.
tPlan the route for venting exhaust to the
outdoors.
tUse the shortest and straightest duct route
possible.
Refer to “ Ductwork installation guidelinesDuctwork installation guidelines
Ductwork installation guidelinesDuctwork installation guidelines
Ductwork installation guidelines”
paragraph for further informations.
tInstall a wall cap with damper or roof cap at the
exterior opening. Order the wall or roof cap and
anytransition needed in advance.
tUse 8" round metal ductwork only.
WW
WW
Wall framing for adequate supportall framing for adequate support
all framing for adequate supportall framing for adequate support
all framing for adequate support
tThis vent hood is heavy.
‘Adequate structure and support must be
provided in all types of installations. The hood
must be secure to vertical studs in the wall, or to
a horizontal support.
tThe vent hood should be on site before nal
framing and wall nishing. This will help to
accurately locate the duct work and electrical
service.
tInstallation will be easier if the vent hood is
installed before the cook-top and countertop are
installed.
Removing the packagingRemoving the packaging
Removing the packagingRemoving the packaging
Removing the packaging
Remove carton carefully, Wear gloves to protect
against sharp edges.
Remove the protective lm covering the product
before putting into operation.

88
88
8Installing the hood
Examples of possible ducting
Ductwork installation guidelines
For safety reasons, ducting should vent directly
outdoors (not into an attic, underneath the house,
into the garage or into any enclosed space).
Keep duct runs as short and straight as possible.
Duct ttings (elbows and transitions) reduce air ow
eciency.
Back to back elbows and“S“ turns give very poor
delivery and are not recommended.
A short straight length of duct at the inlet of the
remote blower gives the best delivery.
Transition to duct from the integral blower or remote
duct transition as close to the downdraft as is pos-
sible.
In order of preference, use
1st. 10" round duct
2nd. 8" round duct
3rd. 3-1/4" x 14" duct
4th. 7" round duct
5th. 3-1/4" x l0" duct
6th. 6" round duct
The use of exible metal round duct should only be
used when no other duct tting exists. Limit use to
short lengths and do not crush when making
corners.
Ductwork and wiring locationsDuctwork and wiring locations
Ductwork and wiring locationsDuctwork and wiring locations
Ductwork and wiring locations
tDetermine the exact location of the vent hood.
tLocate the template packed with the literature.
tThe height installation is determined by the
following image. Mark the location.
tInstallation height: 30" gas cooktop/range or 24"
to 30" electric cooktop/range.
tUse a level to draw a horizontal straight pencil line
on the wall, which is your desired
installation height.
tFind the centerline of the cooktop. Use a level to
draw a vertical straight pencil line on the wall.
CHECK TO BE SURE THE LINE IS PERFECTLCHECK TO BE SURE THE LINE IS PERFECTL
CHECK TO BE SURE THE LINE IS PERFECTLCHECK TO BE SURE THE LINE IS PERFECTL
CHECK TO BE SURE THE LINE IS PERFECTLYY
YY
Y
PERPERNDICULAR.PERPERNDICULAR.
PERPERNDICULAR.PERPERNDICULAR.
PERPERNDICULAR.
30" Gas Cooktop
24" - 30" Electric Cooktop

99
99
9
Installing the hood
Mounting the duct cover bracketMounting the duct cover bracket
Mounting the duct cover bracketMounting the duct cover bracket
Mounting the duct cover bracket
The duct bracket should be installed against the
back wall and ush with the ceiling. This bracket will
hold the telescopic duct cover in place at the top
.
SecurSecur
SecurSecur
Secur e the bracket to the wall:e the bracket to the wall:
e the bracket to the wall:e the bracket to the wall:
e the bracket to the wall:
tAlign the marked centerline on the bracket with
the centerline on the wall.
tMark 2 screw hole locations in the wall.
tDrill 5/16" pilot holes in the marked locations.
tInstall wall fastener anchors.
tDrive wood screws, by hand, into the fastener to
allow anchors to expand. Remove the screws.
tSecure the bracket to the wall with wood screws
and/or fasteners.
Ceiling ductingCeiling ducting
Ceiling ductingCeiling ducting
Ceiling ducting
If the duct will vent straight up to the ceiling:
tUse level to draw a line straight up, from the
centerline on the template to the ceiling.
tMeasure at least 4 -3/4 ”from the back wall to
the circle center of an 8-½”hole on the ceiling.
WW
WW
Wall ductingall ducting
all ductingall ducting
all ducting
If ductwork will vent to rear:
tUse a level to draw a line straight up from the
centerline on the template.
tMeasure at least 23 - 3/4" (the measure might
vary depending on the elbow used) above the
pencil line that indicates the bottom installation
height, to the circle center of an 8-½”diameter
duct hole (Hole may be elongated for duct elbow).
House wiring locationHouse wiring location
House wiring locationHouse wiring location
House wiring location
tThe junction box is located on the top left side of
the hood.
tWiring should enter the back wall at least 20"
above the bottom of the installation height, and
within 5-7/8" and 4-7/8"of the left side of the
centerline.

10 Installing the hood
Install framing for hood supportInstall framing for hood support
Install framing for hood supportInstall framing for hood support
Install framing for hood support
If drywall is present, mark the screw hole
locations. Remove the template.
Cut away enough drywall to expose 2 vertical
studs at the holes location indicated by the
template.
Install two horizontal supports at least ùéX 2é
between two wall studs at the bottom and upper
mounting holes installation location.
room side of the studs.
Use cleats behind both sides of the support to
secure to wall studs.
IMPORIMPOR
IMPORIMPOR
IMPORT T
T T
TANTANT
ANTANT
ANT---- - Framing must be capable ofFraming must be capable of
Framing must be capable ofFraming must be capable of
Framing must be capable of
supporting êûû lbs.supporting êûû lbs.
supporting êûû lbs.supporting êûû lbs.
supporting êûû lbs.
Mounting the hoodMounting the hood
Mounting the hoodMounting the hood
Mounting the hood
WARNING: 2 people are required to lift and position
the hood onto the mounting screws.
Place the template on the wall along the horizon-
tal line, make sure the template is leveled and
centered with the centerline.
Mark“upper”screw holes locations in the wall.
IMPORTANT. Check to be sure that hole locations
are leveled and correctly centered by the vertical
centerline.
Drive“upper”wood screws by hand. Leave ¼“ of
distance between the screw head and the wall.
onto the“upper”screws.
Mark“lower”wood screw holes locations in the
wall using a pencil.

11
Installing the hood
Remove the hood.
Drive“lower”wood screws, by hand. Remove
screws.
Mount the hood onto the“upper”screws.
Drive and tighten the“upper” wood screws, by
hand.
Drive and tighten the“lower”wood screws, by
hand.

1212
1212
12
Connecting the ductworkConnecting the ductwork
Connecting the ductworkConnecting the ductwork
Connecting the ductwork
tInstall ductwork, making connections in the
direction of airow as illustrated.
tPush duct over the exhaust outlet.
tWrap all duct joints and the ange connections
with duct tape for an airtight seal.
tMake the same connection in the wall or ceiling
vent exit.
Installing the hood
Air deector installationAir deector installation
Air deector installationAir deector installation
Air deector installation
(Recir(Recir
(Recir(Recir
(Recirculating accessories)culating accessories)
culating accessories)culating accessories)
culating accessories)
tAssemble the air deector with the duct cover
bracket with 4 assembly screws provided as
shown.
tMeasure from the bottom of the air deector to
the bottom of the hood outlet, as shown.
tCut the duct at the measured size.
tUninstall the air deector removing the 4
assembly screws.
tSlip the duct onto the bottom of the deector.
tPlace the assembled deector and duct over the
exhaust outlet from the hood.
tAssemble the air deector to the duct cover
bracket with 4 assembly screws provided as
shown.
Ductwork
Hood
Duct tape
over seams
Airow

13
Making the electrical connections
Electrical Shock Hazard
wiring this unit.
ê2û Vê2û V
ê2û Vê2û V
ê2û V AC, ê5 or 2û Amp cirAC, ê5 or 2û Amp cir
AC, ê5 or 2û Amp cirAC, ê5 or 2û Amp cir
AC, ê5 or 2û Amp circuit rcuit r
cuit rcuit r
cuit requirequir
equirequir
equired.ed.
ed.ed.
ed.
ELECTRICAL GROUNDING INSTRUCTIONSELECTRICAL GROUNDING INSTRUCTIONS
ELECTRICAL GROUNDING INSTRUCTIONSELECTRICAL GROUNDING INSTRUCTIONS
ELECTRICAL GROUNDING INSTRUCTIONS
THIS APPLIANCE IS FITTED WITH AN ELECTRICAL
JUNCTION BOX WITH ÀWIRES, ONE OF WHICH
ôGREEN/YELLOWÈSERVES TO GROUND THE
APPLIANCE. TO PROTECTYOU AGAINST
ELECTRIC SHOCK, THE GREEN AND YELLOW
WIRE MUST BE CONNECTED TO THE
GROUNDING WIRE INYOUR
HOME ELECTRICAL SYSTEM, AND IT MUST
UNDER NO CIRCUMSTANCES BE CUT OR REMO-
VED.
FailurFailur
FailurFailur
Failure to do so can re to do so can r
e to do so can re to do so can r
e to do so can result in death or electricalesult in death or electrical
esult in death or electricalesult in death or electrical
esult in death or electrical
shock.shock.
shock.shock.
shock.
Remove junction box cover and knockout on the
top left side.
If not already done, install ê/2”conduit connector
in junction box.
Run black ôliveÈ, white ôneutralÈ, and green ôearthÈ
wires ôí êù AWGÈaccording to the National
Electrical Code or CSA Standards and local
codes and ordinances in ê/2”conduit from power
supply to junction box.
Connect black, white, and green wires from
power supply to black, white, and green/yellow
wires in junction box respectively.
These connections should be done always
making reference to the electrical diagram found
inside the hood.
Close junction box cover and reapply screws.
Installing the hood

1414
1414
14
Mounting the duct coverMounting the duct cover
Mounting the duct coverMounting the duct cover
Mounting the duct cover
Position the duct cover over the mounted hood.
Slide the bottom of the duct onto the glass area.
Position the top of the duct over the duct
mounting bracket. If a telescopic duct cover is
used, grab the upper part of the telescopic duct
cover, pull it and place it in the duct cover
mounting bracket.
Secure the top of the duct with 2 assembly
screws provided.
Secure the bottom of the duct with 2 assembly
screws provided.
panel. Check operation of the hood.
Installing the hood
Remove Protective

1515
1515
15
Features
1.1.
1.1.
1. Blower and light controls
2.2.
2.2.
2. Lamp housings
3.3.
3.3.
3. Grease lter Handle
4.4.
4.4.
4. Grease lter
5.5.
5.5.
5. Canopy
6.6.
6.6.
6. Duct cover
7.7.
7.7.
7. Louver holes (User for Recirculating accessories)
Features
t#PUUPNt5PQDownloaded from www.Manualslib.com manuals search engine

16
Controlíbuttons
Controlíbuttons
This hood is equipped with an electronic motor and
lamp control.
ON/OFF light and has a timer function.
In the following drawing are described the main key
functions.
1.íLightíButton1.íLightíButton
1.íLightíButton1.íLightíButton
1.íLightíButton
Press lamp button to turn ON the light ôLamp
state previously OFFÈ.
Press lamp button to turn OFF the light ôLamp
state previously ONÈ.
2.íTimeríButton2.íTimeríButton
2.íTimeríButton2.íTimeríButton
2.íTimeríButton
The default timer setting is êû minutes, and it
can be adjusted between 2û minutes and
êminute.
After pressing the timer button, the control
enters to a timer setup mode, and user can
adjust the timer countdown time with the
“”and “ ”buttons within 5 seconds.
The timer can be initiated immediately
pressing the timer button, after setting the
timer duration or pressing the timer button
twice ôdefault êû minutes settingÈ.
If no action occurs within 5 seconds, the
countdown will start.
During the timer setup the “ ”and “ ”
buttons are dedicated to the timer and no
motor action will occur.
Once the timer is initiated, it can be cancelled
by pressing the timer button again.
3.íDisplay3.íDisplay
3.íDisplay3.íDisplay
3.íDisplay
Shows the hood settings.
4.í“4.í“
4.í“4.í“
4.í“ ”íButton.íSpeedíDecr”íButton.íSpeedíDecr
”íButton.íSpeedíDecr”íButton.íSpeedíDecr
”íButton.íSpeedíDecreaseí/íOFFeaseí/íOFF
easeí/íOFFeaseí/íOFF
easeí/íOFF
This button is used to decrease the fan speed,
or turn OFF the fan.
The fan will turn OFF if the “ ”button is
If the fan is at second speed and the“ ”
speed.
If the fan is at third speed and the“ ”key is
pressed, the fan will be set to second speed.
If the fan is at fourth speed and the “ ”
button is pressed, the fan will be set to third
speed.
If the fan is OFF and the “ ”button is
pressed, the control backlight will light up.
5.í“5.í“
5.í“5.í“
5.í“ ”íButton.íSpeedíIncr”íButton.íSpeedíIncr
”íButton.íSpeedíIncr”íButton.íSpeedíIncr
”íButton.íSpeedíIncreaseí/íONeaseí/íON
easeí/íONeaseí/íON
easeí/íON
This button is used to increase the fan speed,
or turn ON the fan.
The fan will turn ON if the “ ”button is
pressed and the hood was OFF.
”button
is pressed, the fan will be set to second
speed.
If the fan is at second speed and the“ ”
button is pressed, the fan will be set to third
speed.
If the fan is at third speed and the“ ”
button is pressed, the fan will be set to fourth
speed.
If the fan is at fourth speed and the “ ”
button is pressed, a beep will sound.

1717
1717
17
Special functions
Clock prClock pr
Clock prClock pr
Clock programmingogramming
ogrammingogramming
ogramming
tThe clock can be reprogrammed at any time except during an active timed function.
tThe clock can be displayed in a twelve hour format and valid clock times are from 1:00 to 12:59.
tThe clock can be reprogrammed pressing the “TT
TT
Timerimer
imerimer
imer”button for 5 seconds, and after, the clock can be
adjusted with the“ ”and“ ”buttons. Colon“:”will ash indicating clock programming mode.
tThe user can have minute increments / decrements of 1 minute, but if the user keep pressing the“ ”/
” ” buttons for more than 1 second, the increments / decrements will be of 5 minutes.
During this option the control will round to the nearest 5 minutes.
tThe user can nish on reprogramming the clock pressing the “ TT
TT
Timerimer
imerimer
imer” button.
tAfter 1 minute of no button pressed the control will accept the programmed clock time and will add one
minute to the set clock.
GrGr
GrGr
Grease lter saturation alarmease lter saturation alarm
ease lter saturation alarmease lter saturation alarm
ease lter saturation alarm
tAfter thirty fan functional hours, the display will show“ GrGr
GrGr
Grease Filterease Filter
ease Filterease Filter
ease Filter” if the fan is active.
When this icon is shown in the display, the grease lters installed are required to be washed.
tTo reset the grease lter saturation alarm the user must press the“ ” button for 5 seconds, after this
action the icon“ GrGr
GrGr
Grease lterease lter
ease lterease lter
ease lter” is not displayed, and the hood has the normal display operation.
CharChar
CharChar
Charcoal lter saturation alarm (Recircoal lter saturation alarm (Recir
coal lter saturation alarm (Recircoal lter saturation alarm (Recir
coal lter saturation alarm (Recirculating accessories)culating accessories)
culating accessories)culating accessories)
culating accessories)
tAfter one hundred and twenty functional hours of the fan, the display will show“ CharChar
CharChar
Char coal Filtercoal Filter
coal Filtercoal Filter
coal Filter”if the fan
is active. When this icon ashes on display, the charcoal lters installed are required to be replaced or
reactivated.
tTo reset the charcoal lter saturation indication the user must press the“ ”button for 5 seconds, after
this time the icon“ CharChar
CharChar
Char coal ltercoal lter
coal ltercoal lter
coal lter”is not displayed and the hood has the normal display operation.
Audible signal activation and deactivationAudible signal activation and deactivation
Audible signal activation and deactivationAudible signal activation and deactivation
Audible signal activation and deactivation
tThe audible signals can be activated or deactivated pressing the“LightLight
LightLight
Light”button for 5 seconds.
tIf the audible signal is activated, a tone must sound and the“ SndSnd
SndSnd
Snd”symbol must appear on the display for
2 seconds.
tIf the audible signal is deactivated, the“ SndSnd
SndSnd
Snd”symbol must appear on the display for 2 seconds and no
tone must sound.
CharChar
CharChar
Charcoal lter inclusion and exclusion (Recircoal lter inclusion and exclusion (Recir
coal lter inclusion and exclusion (Recircoal lter inclusion and exclusion (Recir
coal lter inclusion and exclusion (Recirculating accessories)culating accessories)
culating accessories)culating accessories)
culating accessories)
tThe charcoal lter inclusion or exclusion can be set by pressing the “ ”and“ ” buttons at the same
time for 5 seconds.
tThe Inclusion or exclusion of charcoal lter must be selected while the lamps and the motor are OFF.
tWhen the charcoal lter has been excluded, the charcoal lter alarm is disabled.
Heat sensorHeat sensor
Heat sensorHeat sensor
Heat sensor
tThe control is equipped with a heat sensor that will turn on the blower at second speed if excessive heat
occurs (over 158° F158° F
158° F158° F
158° F or 70°C70°C
70°C70°C
70°C) surrounding the control area.
tIf the blower is OFF or if it is operating at rst speed, the blower will be set automatically to second speed,
the display shows the word " CArECArE
CArECArE
CArE" to indicate that heat sensor has detected an excessive heat.
tDuring this state, the user may raise the blower speed to third speed but can not decrease the speed.
tWhen the temperature level on the hood drops to normal, the blower will operate in the setting dened by
the user before the alarm occured.
Control buttons - Special functions

1818
1818
18
For Best rFor Best r
For Best rFor Best r
For Best resultsesults
esultsesults
esults
tContinuous use of the fan system while cooking helps keep the kitchen comfortable and less humid.
tIt also reduces cooking odors and soiling moisture that create a frequent need for cleaning.
tTurn the blower on before starting to cook.
tUse a rear burner when browning or pan frying meat.
tOpen a window or inside door slightly.
tClean the lters and the wall behind the lters frequently.
tThe blower should be turned on for a few minutes beforbefor
beforbefor
beforee
ee
e cooking in order to establish air currents upward
through the hood. Thus when heat, smoke, moisture, grease and cooking odors are produced, they will
be carried outside instead of drifting into other rooms.
tUse the low speeds for normal use and the higher speeds for strong odors or fumes.
tDrafts across the range or cooktop will cause the escape of heat, smoke, moisture, grease and cooking
odors from the hood. Such drafts should be prevented in so far as possible.
tThe best job of ventilation in the kitchen is done where the only air currents are those created by the
blower itself.
tFor Gas Cooktops,For Gas Cooktops,
For Gas Cooktops,For Gas Cooktops,
For Gas Cooktops, a lower blower speed should be used if:
tthe gas ame is being distorted by the air movement.
tthe burner continually sparks (clicks)
tthe burner ame repeatedly blows out.

1919
1919
19
Care and cleaning
The eciency of the range hood system depends on
the cleanliness of the intake and lters.
The frequency of cleaning depends on the amount
and type of cooking.
tDo not use the ventilating system without the
lters in place or with grease-laden lters or
surfaces.
To avoid risk of re and explosion do not use
ammable liquids or solvents.
Always unplug or disconnect the appliance from the
power supply before servicing.
Be sure the entire hood (including the lters and light
bulbs) has cooled and grease has solidied before
attempting to clean any part of the appliance.
FiltersFilters
FiltersFilters
Filters
The metal grease lters are made of stainless steel
anodized aluminum and are long lasting.
TT
TT
To Remove The Metal Gro Remove The Metal Gr
o Remove The Metal Gro Remove The Metal Gr
o Remove The Metal Gr
tTurn the fan and lights o.
tPull the spring release handle.
TT
TT
To Replace The Metal Gro Replace The Metal Gr
o Replace The Metal Gro Replace The Metal Gr
o Replace The Metal Gr
ease Filters
tReverse procedure.
TT
TT
To Clean Filterso Clean Filters
o Clean Filterso Clean Filters
o Clean Filters
tttttIt is recommended that the lters be washed at
least once a month; they can be washed by hand
or in the dishwasher.
tDrain water through edge holes and let each lter
dry thoroughly before replacing it.
LightsLights
LightsLights
Lights
Before replacing the lamps, switch power o at
service panel and lock service panel disconnecting
means to prevent power from being switched on
accidentally.
NOTE: TNOTE: T
NOTE: TNOTE: T
NOTE: Turur
urur
urn ofn of
n ofn of
n off the lights and fan. Allow the lightsf the lights and fan. Allow the lights
f the lights and fan. Allow the lightsf the lights and fan. Allow the lights
f the lights and fan. Allow the lights
toto
toto
to coolcool
coolcool
cool beforbefor
beforbefor
before handling.e handling.
e handling.e handling.
e handling. If new lights do notIf new lights do not
If new lights do notIf new lights do not
If new lights do not
operate be suroperate be sur
operate be suroperate be sur
operate be sur e lights are lights ar
e lights are lights ar
e lights are inserted corre inserted corr
e inserted corre inserted corr
e inserted corr ectly beforectly befor
ectly beforectly befor
ectly beforee
ee
e
calling service.calling service.
calling service.calling service.
calling service.
Replace LightsReplace Lights
Replace LightsReplace Lights
Replace Lights
tRemove the inner lamp lens cover by inserting a
small at blade screwdriver into each of the three
slots and gently prying it free.
NOTE: Do not remove the outer trim ring (lamp
assembly).
tGrasp the bulb and pull it straight out.
tReplace with 12 volt, 20 watt halogen bulbs with
a G4 base SUITABLE FOR USE IN OPEN
LUMINAIRES.
Follow package dirFollow package dir
Follow package dirFollow package dir
Follow package directions, wear gloves, do notections, wear gloves, do not
ections, wear gloves, do notections, wear gloves, do not
ections, wear gloves, do not
touch bulb with your bartouch bulb with your bar
touch bulb with your bartouch bulb with your bar
touch bulb with your bar e ngers.e ngers.
e ngers.e ngers.
e ngers.
tReplace inner cover by inserting the three
retaining tabs into the three slots and pressing
them rmly in place.
Care and cleaning
ease Filtersease Filters
ease Filtersease Filters
ease Filters

2020
2020
20
Optional CharOptional Char
Optional CharOptional Char
Optional Charcoal Filterscoal Filters
coal Filterscoal Filters
coal Filters
If the model is not vented to the outside, the air will be recirculated through disposable charcoal lters that
help remove smoke and odors.
The charcoal lters cannot be cleaned.
They must be replaced.
The charcoal lters are clipped inside of each metal grease lter (mounting instructions included with charcoal
lters kit).
The charcoal lters should be replaced every 4-6 months (depending on hood usage).
NOTE:NOTE:
NOTE:NOTE:
NOTE: DO NOT rinse, or put charcoal lters in an automatic dishwasher.
NOTE:NOTE:
NOTE:NOTE:
NOTE: Charcoal lters are notnot
notnot
not included with the hood.
They must be ordered from your supplier.
Order the needed kit specifying your hood model and width size.
CharChar
CharChar
Char coal lter placement (Recircoal lter placement (Recir
coal lter placement (Recircoal lter placement (Recir
coal lter placement (Recirculating accessories)culating accessories)
culating accessories)culating accessories)
culating accessories)
Fit the charcoal lter mattress on the upper side of each grease lter.
Use provided springs to x it in place.
Note:Note:
Note:Note:
Note: When removing for replacing for a new one do not remove Fixing Springs, simply pull out and rotate
outwards.
Care and cleaning
remove nger prints and give added shine, use
cleaners such as Stainless Steel Magic. Do not allow
any cleaning compounds to remain in contact with
stainless steel for extended periods.
Plastic surfaces:Plastic surfaces:
Plastic surfaces:Plastic surfaces:
Plastic surfaces: Wipe with a moist soapy sponge.
Rinse and dry.
Aluminum Mesh Filters: Clean lters in the dish-
washer or by agitating in sudsy water. Ensure that
there is no soil trapped in the ne mesh. Dry the
lters before reinstalling them.
Anodized Aluminum surfaces:Anodized Aluminum surfaces:
Anodized Aluminum surfaces:Anodized Aluminum surfaces:
Anodized Aluminum surfaces: Top cap is not remov-
able. Wash top and underside with hot sudsy water.
Rinse and wipe dry or apply Fantastic® or Formula
409® rst to a clean sponge or paper towel and
wipe clean. DO NOT USE powdered cleansers or
steel wool pads.
CleaningCleaning
CleaningCleaning
Cleaning
tAlways use the mildest cleaner that will do the
job. Use clean, soft cloths, sponges or paper
towels.
tRub stainless steel nishes in the direction of the
grain. Wipe area dry to avoid water marks.
tAfter cleaning, place all parts in their proper
positions before using.
The cleaners recommended below indicate a type
and do not constitute an endorsement. Use all
products according to package directions.
Hood SurfaceHood Surface
Hood SurfaceHood Surface
Hood Surface
Painted Surfaces:Painted Surfaces:
Painted Surfaces:Painted Surfaces:
Painted Surfaces: For general care, wipe the outside
of the hood with sudsy water or household cleaners
such as Fantastic or Formula 409, rinse well and dry
with a clean soft cloth to avoid water marks.
Stainless Steel Surfaces:Stainless Steel Surfaces:
Stainless Steel Surfaces:Stainless Steel Surfaces:
Stainless Steel Surfaces: Wipe and dry stainless
steel in the same direction as the grain. Avoid using
too much pressure, which may mar the surface. To