Electrolux VERSA User manual

Q&CI - Technical Support 0 XXX XX XX –XX Rev. XX
© ELECTROLUX HOME PRODUCTS
Consumer Service - EMEA
Quality & Continuous Improvement - Technical Support
SERVICE MANUAL
COOKING
FOR INTERNAL AND PARTNERS USE ONLY
For internal and partners use only.
HOOD
VERSA Range
EN
Publication number
599 8170 –86
Edition: 04/2018 - Rev. 00

Q&CI - Technical Support 1 599 8170 –86 Rev. 00
CONTENTS
CONTENTS 1
1PURPOSE OF THIS MANUAL 2
2SAFETY 3
3VERSA HOOD 4
4ACCESSIBILITY 5
5CIRCUIT 16
6TROUBLE SHOOTING 20

Q&CI - Technical Support 2 599 8170 –86 Rev. 00
1 PURPOSE OF THIS MANUAL
The purpose of this Service Manual (SM) is to provide Service Engineers who are already familiar with the repair procedures of Hoods
This SM will provide information on:
oHood Range
oAccessesbility
oTechnical and functional characteristics
oTrouble shooter
Document Revisions
Rev.
Date
Description
Author
00
04/2018
Document creation
Said Hatem
Acronyms and Abbreviations
Terms
Initialism
Grease Filter Assembly
GFA
Slide-Out Assembly
SOA
Slider Guide
SG
Candle Lamp
CL
Spot Lamp
SL
Light Diffuser
LD
Lamp Holder
LH
Feeder Cable
FC
Control Assembly
CA
Led Driver
LD
Blower Assembly
BA

Q&CI - Technical Support 3 599 8170 –86 Rev. 00
2 SAFETY
All the work to be performed inside the appliance requires specific skills and knowledge and may only be carried out by
qualified and authorised Service Engineers.
Before you access internal components, take the plug out of the socket to disconnect the power supply.
Use a pair of safety gloves to avoid sharp cuts.
Some of the components in the mechanical part could cause injuries, so wear suitable protection and proceed with
caution.
Prior to touching the light bulbs ensure they are cooled down.

Q&CI - Technical Support 4 599 8170 –86 Rev. 00
3 VERSA HOOD
3.1 Hood Features
It's a mechanical device which situated upper the cooktop, mainly contains a Blower Assembly, Grease Filters and a Control Assembly.
1
Control Assembly
2a
Light Diffuser & Candle Lamp
2b
Spot Lamp
3
Grease Filter
4
Blower Assembly
5
Slider
6
Slide Out Assembly
7
Glass

Q&CI - Technical Support 5 599 8170 –86 Rev. 00
4 ACCESSIBILITY
4.1 Grease Filter Assembly (GFA)
1. Slide the latch in the handle structure leftwards to unsnap GFA.
2. Release the GFA from the slots in the left side of its frame.
Placing back the GFA: Start with the step 2 placing the guide projections in the
guide and snap the handle latch
! Depending on the size of the hood, number of filters vary
4.2 Slide-Out Assembly (SOA)
1. Pull out the slider to reach the backside of the SOA.
2. Unfasten 2* screws which secure the SOA to the Slide.

Q&CI - Technical Support 6 599 8170 –86 Rev. 00
4.3 Glass
Perform chapter 4.1 and the first step of chapter 4.2
1. Unfasten 2* screws which secure the glass blocker.
2. Remove the glass blocker.
3. Slide the glass leftward.
4. Push up and slide rightward to remove the glass.

Q&CI - Technical Support 7 599 8170 –86 Rev. 00
4.4 Slider
Perform chapter 4.1 and the first step of chapter 4.2
1. Unfasten 4* screws which secure the slider.
2. Unfasten 2* screws which secure the slider blockers.
3. Pull out to remove the Slider.
4.5 Slider Guide(SG)
Perform the chapter 4.4
1. Unfasten 4* screws which secure the SG to the Slider.
2. Pull out to remove the SG.

Q&CI - Technical Support 8 599 8170 –86 Rev. 00
4.6 Lamp
4.6
Lamp
Picture
Procedure to access
4.6.1
Candle Lamp
See subchapter 4.6.1
4.6.2
Spot Lamp
See subchapter 4.6.2

Q&CI - Technical Support 9 599 8170 –86 Rev. 00
4.6.1 Candle Lamp (CL)
Perform chapter 4.1 and the first step of chapter 4.2
1. Turn the bulb in anti- clockwise direction to take the CL out and in clockwise direction
to place it back.
!Assure that power cable is plugged out
! Check if the lamp is hot
4.6.2 Spot Lamp (SL)
Perform chapter 4.1
1. Pull out the slider.
2. Push the 2 snaps to unsnap the SL.
3. Unsnap to remove the SL.