Element4 Trisore 50e User manual

LEAVE THESE INSTRUCTIONS WITH THE DEVICE
For all “Element4 - Electric Fires”
INSTALLATION MANUAL

INSTALLATION MANUAL
2

INSTALLATION MANUAL
3
THIS PRODUCT IS NOT SUITED AS A PRIMARY HEAT SOURCE.
BEFORE INSTALLATION AND USE, READ THIS BOOKLET AND KEEP IT IN
RANGE OF THE FIRE FOR POSSIBLE LATER USE.

INSTALLATION MANUAL
4

INSTALLATION MANUAL
5
Content
1 CE statement 6
2 Waranty 6
3 Important safety information 7
4 Connection 7
5 Installation method 8
6 Hollow wall installation method 8
7 Decorating the replace 10
8 User Instructions 10

INSTALLATION MANUAL
6
1 CE statement
We hereby declare that the design and construction of the
Element4 electric appliances are complying to the essential
demands and regulations for electric products.
Product:
• Electric fire
Models:
• Modore-, Bidore- and Trisore 50e
• Modore-, Bidore- and Trisore 80He
• Modore-, Bidore- and Trisore 100e
• Modore-, Bidore- and Trisore 150e
• Modore-, Bidore- and Trisore 180e
All Element4 Electric fires meet the requirements of the EC
Directives. These directives have been met by compliance with
the following standard
• EN 55014-1:2006 + A2:2011
• EN 55014-2:2015
• EN 61000-3-2:2014
• EN 61000-3-3:2013
• EN 60335-1:2012 + A1:2014
• EN 60335-2-30:2009+A11:2012
This declaration loses its validity when changes to the device
are made without the written permission by Element4. You
can ask for a copy of the test certificates of all models via
our general e-mail adress, which is found on the back of this
manual.
J. Kempers
CEO
2 Waranty
Should this device show defects within 24 months of purchase
due to shortcomings in construction, material or workmanship,
the product will be repaired free of charge under the following
conditions:
It is the responsibility of the buyer to prove that the device is
covered by the warranty, e.g. with a proof of purchase.
Any guarantee will lapse if
• unauthorized repairs or modifications have been made to
the electric fireplace
• in the event of an accident, misuse or damage caused by
an incorrect installation
• damage occurred during transport to or from the
• repairer, and changed or missing serial numbers.
Parts replaced under this warranty will become our property.
The company is not liable for consequential damage or any
other damage arising from or related to this electric fireplace.
This warranty does not apply to heating elements, lamps or
fuses. Service visits where no errors are found and installation
errors are not covered by the manufacturer’s warranty.
In this case, the maintenance technician employed by us will
charge you for the service visit.
This guarantee is an addition to and does not aect the legal
rights of the buyer as a consumer.
Replacement plug
Caution: when removing the molded plug and connection to
a fused tap through a unqualified person, the guarantee will
lapse.

INSTALLATION MANUAL
7
3 Important safety information
Please read these instructions before installation or use and
keep this booklet handy for future reference
This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without
supervision
The instructions shall state that the heater must not be located
immediately below a socket outlet.
WARNING
in order to avoid overheating, do not cover the heater.
Children of less than 3 years should be kept away unless
continuously supervised
Children aged from 3 years and less than 8 years shall only
switch on/o the appliance provided that it has been placed
or installed in its intended normal operating position and they
have been given supervision or instruction concerning use
of the appliance in a safe way and understand the hazards
involved. Children aged from 3 years and less than 8 years shall
not plug in, regulate and clean the appliance or perform user
maintenance.
CAUTION
Some parts of this product can become very hot and cause
burns. Particular attention has to be given where children and
vulnerable people are present
General Warnings:
• Never leave children unsupervised with an unguarded
heater.
• Never obstruct or cover the heater outlet.
• Never install or use this product where it may come in
contact with water i.e. a bathroom or wet room.
• Never use aerosols or steam cleaners near this product.
• Never route the electric cable near the heater outlet.
• Never route the electric cable under carpets or floor
coverings.
• Never install this product close to curtains or combustible
materials.
• Never use the heater to dry clothes or other objects.
• Never remove the fireplace surrounding without isolating
the electric supply.
4 Connection
This appliance must only be connected to a 230/240 Volts AC
50Hz supply. Before connecting the fire, check that the supply
voltage is the same as stated on the fire.
This appliance must only be used on a AC supply, fuse rating
13Amp. The wires in the mains lead are coloured in accordance
with a standard UK supply, these being:
• GREEN/YELLOW – EARTH
• BLUE – NEUTRAL
• BROWN – LIVE
As the colours of the mains lead of this appliance may not
match the coloured markings used to identify the terminals in a
plug, please observe the following
• The green and yellow wire must be connected to the
terminal in the plug which is marked with the letter E or
Earth symbol.
• The blue wire must be connected to the terminal in the
plug which is marked with the letter N.
• The brown wire must be connected to the terminal in the
plug marked with the letter L.
• Replace fuses only with fuses of the correct size and rating.
Maintenance
Maintenance to this device may only be done by a qualified
professional. It is adviced to maintain your fire at least once
every 12 months.
WARMING:
Before reparation or maintenance check whether the fire is
unplugged.
4.1 Important electrical safety
This appliance must never be installed above or in front of a
fixed electric socket.
The electrical socket must be easily accessible to isolate the
supply during maintenance and cleaning.
This appliance is supplied with a two meter power lead, which
has a 13Amp moulded three pin plug to connect to a standard
230/240V plug socket.
This appliance must always be earthed. If in any doubt consult
a suitably competent person.
CAUTION
The LED light system shall be replaced by electrically
competent personnel only (LP – These cannot be user
replaceable since they will allow access to live parts)

INSTALLATION MANUAL
8
5 Installation method
Built in models
This product has been designed to be installed into a plaster
board, or existing masonry chimney breast.
Please seek advice from a professional, with reference to the
structural integrity of the installation site.
If the product is to be installed into a open chimney or flue, it is
important that the chimney/flue is blocked o to prevent any
up/down draughts and falling debris which could restrict
and alter the airflow to the product.
It is also important to ensure that the product has a minimum
internal clearance directly above and below the product of
50mm, this is to ensure that the product can circulate the
required airflow for the heater unit.
The product should never be sealed into a opening with the
use of silicones or adhesives as this can also alter the airflow
and hinder any further servicing of the product
Heating shut-off protection
This protection protects the product against damage.
When the air circulation is impeded, the fire is switched o
automatically. This can happen with incorrect installation of
the fireplace, or blockages.
To reset the heating function:
• Remove the plug from the socket.
• Allow the product to cool.
• If the device has cooled down suiciently, remove any
blockages and check the installation.
Aer 10 minutes, the thermostat switch (trip protection) of the
heater is reset.
Note:
Both the eect fan and the heating fan produce a so sound
that is associated with normal operation of the stove.
6 Hollow wall installation method
In all Element4 fireplaces, a free space of 100mm at least 50mm
must be maintained immediately above and below the main
housing for good air circulation. (Failure to do so may cause
problems for the heating and flame function).
Each Element4 fireplace is supplied with one or more wall
mounting brackets.
Determine the height at which the finished Element4 fireplace
should be positioned in relation to the floor level.
Note:
The minimum distance to the floor is 300 mm
Attach the wall bracket to the wall, making sure that you use
the correct fasteners that match the respective wall - hollow or
solid.
Hang the Element4 fireplace on the bracket and secure it in
place with the wall bracket at the top of the fireplace.
Insert the plug of the IEC-compliant power cable into the IEC-
compliant socket and ensure that it is firmly pushed.
Note:
Place the device near a suitable socket so that it can be
connected to the mains.
It is important that the outlet is located outside the installation
location so that the socket is easily accessible and the plug
can be disconnected from the stove aer installation.
Aer the fire is attached to the wall and connected to the
socket, the surround (the chimney) can be placed around it.
Construct the hollow installation space for the electric fire in
the desired dimensions. For minimum opening dimensions,
see Figure 1 and Table 1.It is important that you take into
account the finished front when determining the depth of the
frame construction.
It is important that a header/lintel is also placed at the desired
height, so that the weight of the wall made will not come to rest
on the appliance.
Make the cut in the plasterboard / finishing plate and install the
fireplace, making sure that the plaster board edges connect to
the inside of the cut in the plate.
CAUTION
In order to avoid a hazard due to inadvertent resetting of the
thermal cut-out, this appliance must not be supplied through
an external switching device, such as a timer, or connected to a
circuit that is regularly switched on and o by the utility.

INSTALLATION MANUAL
9
The minimum opening dimensions required are in the table
below
Model Width (mm) Depth (mm) Height (mm)
50e 530 305 610
80He 835 305 790
100e 1065 305 560
150e 1565 305 560
180e 1785 305 615
The definite opening dimensions aer installation are in the
table below
Model Width (mm) Depth (mm) Height (mm)
50e 495 305 610
80He 802 305 590
100e 1003 305 355
150e 1505 305 355
180e 1750 305 410
H
B
D
Wall Brackets
Plaster board edges

INSTALLATION MANUAL
10
8 User Instructions
The Element4 electric fires can be used with the Element4
Electric fire application available on Android and iOS.
For a full instruction on how to use your electric fires we refer
you to the user manual.
7 Decorating the replace
Removing glass front side
Follow the next steps for temoving the glass front window and
place the decorative logset.
1. Remove the two screws located in the bottom glass
retaining bar.
2. Remove the bottom glas retaining bar.
3. Remove the glass by pulling the second retaining bar
away from the body of the fire, ensure that the glass is
supported at all times.
Suction cup
A suction cup is provided to help aid this step. Please note the
suction cup is not to hold the full weight of the glass.
Tip
It is recommended with the 150e and 180e models to carry out
these steps with two persons.
4. Place the log set as stated below and replace the glass in
reversed order of step 1 to 3.
Placing the logset
Every models is deliverd standard with a European logset. The
style and size of the set varies between models.
The logs can be arranged to personal preference and o not
influence the flames or the proper functioning of the fire.
Step 1
Step 3
Step 2
Step 4

INSTALLATION MANUAL
11

Paxtonstraat 23
8013 RP Zwolle
The Netherlands
[email protected]
www.element4.nl
ELEMENT 4 B.V.
AUGUST 2018