Elenco Electronics XP-605 User manual

Variable Voltage
Power Supply
Instruction
Manual
Model XP-605 / XP-752
ElencoTM Electronics, Inc.
150 W. Carpenter Avenue
Wheeling, IL 60090
[phone]
http://www.elenco.com
e-mail: [e-mail]
REV-A
SPECIFICATIONS
Input Voltage 120V +10% 60Hz +2Hz
Source Effect CV < 0.01% +1mV
(Line regulation) CC < 0.2% +1mA
Loading Effect CV < 0.01% +3mV (Iout < 3A) CV < 0.01% +5mV (Iout > 3A)
(Load Regulation) CC < 0.2% +3mA (Iout < 3A) CC < 0.2% +5mA (Iout > 3A)
Ripple & Noise CV < 0.5mV rms (Iout < 3A) CV < 1.0mV rms (Iout > 3A)
CC < 3mA rms (Iout < 3A) CC < 6mA rms (Iout > 3A)
Protection Current limit and short circuit protection.
Voltage Display Accuracy LED +1% +2 digits, Analog +2.5% FSR
Current Display Accuracy LED +2% +2 digits, Analog +2.5% FSR
Environment 0 - +40OC, relative humidity <90%
TWO YEAR WARRANTY
All ElencoTM models are guaranteed for two full years on all parts
and service. For the first 3 months, your power supply is
covered at absolutely no charge. For the remaining 21 months,
a nominal service charge is required to cover shipping and
handling.
When returning merchandise for repair, please include
proof of purchase, a brief letter of explanation of problem,
and sufficient packing material. Before returning any
merchandise please call our service department at (847)
541-3800 to obtain a return authorization number (RMA).
Setting Current Limit (XP-605 only)
1. Adjust the current and voltage control knobs fully counter-
clockwise.
2. Short the positive to the negative output terminal.
3.
Press the power ON/OFF switch to ON. The CC LED should be lit.
4. Turn the voltage coarse knob clockwise 1/2 turn.
5. Set the maximum output current by turning the current coarse
knob clockwise.
This now limits the output current to your setting.

INTRODUCTION
Congratulations on your selection of a top quality power supply! The
XP-605 has an output of 0-30VDC @ 5A; the XP-752 has an output
of 0-50VDC @ 3A. Their features include fine and coarse controls
for voltage and current, and contains two analog volt/current meters
(XP-605); two digital volt/current meters (XP-752).
The supply incorporates an externally controlled current cutoff
circuit with an LED indicating current overload. Protected against
short circuits and overloads.
OPERATING INSTRUCTIONS
1. Check that the voltage rating of the equipment does not exceed
the power supply’s rating.
2. Plug the line cord into an AC outlet.
Constant Voltage Mode
1. Turn the current control (coarse and fine) knobs fully clockwise
and the voltage control knobs fully counter-clockwise.
2.
Press the power ON/OFF switch to ON. The CV LED should be lit.
3. Turn the voltage control knobs clockwise to the desired output
voltage.
4. Connect the positive and the negative output terminals to a load
or similar component.
Constant Current Mode
1. Turn the voltage control knobs (coarse and fine) fully clockwise
and the current control knobs (coarse and fine) ¼ clockwise.
2.
Press the power ON/OFF switch to ON. The CV LED should be lit.
3. Connect the positive and the negative output terminals to a load
or similar component.
4. Turn the current control knobs clockwise to the desired output
current value.
Note XP-752:
Current limiting less than ½A or a shorted output activates the
short circuit protection, turning the unit off. To reset unit,
remove the short or load and readjust current limiting control.
1. Voltage Meter
2. Current Meter
3. Course Voltage Adjustment
4. Fine Voltage Adjustment
5. Course Current Adjustment
6. Fine Current Adjustment
7. Current Limit Indicator (Lit when overload condition)
8. Voltage Indicator (Lit for normal operation)
9. Power Switch
10. Negative Output Terminal
11. Ground Terminal
12. Positive Output Terminal
13. Zero Adjust (XP-605 only)
1
2
3
4
5
6
7
8
91110 12
13
DC POWER SUPPLY
CURRENT VOLTAGE
C.C. C.V.
FINE COARSE FINE COARSE
POWER
GND +–ON OFF