ELEQ LS-84 User manual

83969 / EN2002
Technical Specification
Safety and environmental conditions
CE marking
LV directive 2014/35/EC
RoHS directive 2011/65/EU
WEEE directive 2012/19/EU
Standard
EN-IEC 61439-2:2011
This product is designed to be safe under the following
conditions:
Specification
Environmental conditions
Operating temperature:
Relative humidity:
Protection degree:
Installation class:
Pollution degree:
-5°C - +55°C
5% - 85%, non condensing
IP23
|| (double insulation)
2
Application conditions
Umax:
InA:
Frequency:
Fuse:
Strain relief:
Maximum wire cross section
and torque :
Diameter ø (mm)
Height (mm)
400V
63A (mantle terminals)
50Hz
2 or 3x D01 (E14), max 16A
Yes, maximum 2 ground cables
23mm and 2 light poles cords
Terminal N, 1, 2, 3: 2x 16mm2, 2-
4Nm
Terminal 4, 5, 6, 7: 2.5mm2 1-2Nm*
84
279,5
Storage
Temperature:
Relative humidity:
-20°C - +70°C
5% - 85%, non condensing
* Multi-wire flexible conductors must be assembled in ring-tongues,
ferrules or wire pins.
Specification per type
5L4162
5L4163
Fuse
included
2 x 6A
3 x 6A
PE-N
connection
No
No
Weight (gr)
560
570
Please be aware, product liability, standards and warranty are all
expired when modifications on the product are made.
ELEQ reserves the right to carry out modifications on its products, in
order to improve them, without prior notice.
Safety instruction
All activities for installation, commissioning and maintenance of
this connection box must be performed by qualified personnel
that has the knowledge of applicable safety precautions. This
guide assumes that the reader of this document has sufficient
electro-technical knowledge to understand the content of this
document.
General
The LS-84 is a connection box for public lighting and intended
to be used in lighting poles. The connection box should be
mounted in a weather protected and dry location. In the
connection box the incoming (ground) cable can be connected.
If desired, looped circuits wiring to the next lighting pole is
possible. The cable of the armature should be connected on
the outgoing terminals.
Fuses protect the installation against overload and short-
circuiting.
Explanation of symbols
This product is designed according to the
EN-IEC 61439-2:2011 standards and meets the
requirements of theLow Voltage Directive 2014/35/EC.
Read the installation guide before mounting the
product. Unprofessional work activities on electrical
installations may result in a threat of danger to the life
and health of human beings and livestock!
RoHS Directive 2014/35/EC
ELEQ states that it uses qualified components in its
products only from manufacturers which meet the
requirements of the European Directive for the
"Restriction of use of certain Hazardous Substances
WEEE Directive 2012/19/EU
This equipment should not be disposed as unsorted
municipal waste. Contact a qualified recycler for
disposal.
LS-84 Connection Box for
Public Lighting
Installation Guide
5L4162
LS-84 5L4162
5L4163
Read this installation guide before installing the product
5L6041

v
Always avoid working on live parts of an installation.
Functional Description
The connection boxes of the 5L41xx series all are intended to
be fitted with one D01 fuse. The fuse capacity is limited to 16A.
Assembly
Attention
Remove the fuse during assembly of the connection boxes
1. Ensure a safe working area during assembly, maintenance
and inspection of the connection box. Disconnect the power
of the primary circuit and make sure it cannot be enabled
unintentionally.
2. Remove the transparent lid, fuse and the intermediate
cover. Mount the connection box with the upper and lower
connection in the lighting pole.
3. Connect the incoming and (if present) outgoing ground
cable to terminals N, 1, 2, 3 and 4.
4. Mount the outgoing cables to the armature(s) on terminals
4, 5, 6 and 7 (5L4163 only).
5. Tightly mount strain relief block.
6. Check if the connections are mounted properly and firmly
and place the intermediate cover.
7. Install the fuse. Note: fuse type: D01 (E14), max 16A.
8. Mount the transparent lid and screw tightly.
Incoming
N = Neutral
1 = Phase L1
2 = Phase L2
3 = Phase L3
Outgoing
4 = Neutral wire to armature
5 = Phase L3 wire to armature
6 = Phase L1 wire to armature
7 = Phase L2 wire to armature
If required, incoming terminals N, 1,
2 and 3 can also be looped to the
next lighting pole.
Wiring Diagram
Maintenance and inspection
The connection box should be situated on a dry and clean
location.
The connection box should be mounted firmly.
The connections should be mounted firmly.
Attention
Always avoid working on live parts of an installation.
Disassembly instruction
1. Disconnect the power of the main circuit and make sure it
cannot be enabled unintentionally.
2. Unmount the transparent lid.
3. Remove the fuses.
4. Remove the strain relief block.
5. Disconnect the ground cables.
6. Disconnect the connection box from the lighting pole.
Recycling
When the product has reached ‘end of life’, it must be recycled.
Do not dispose this product as unsorted municipal waste.
Contact a qualified recycler for disposal.