Eletech HDDNTELL DP-200 User manual

Hold-n-Tell TM
DP-200 On-HoldSystem
User’s Manual
Revision 1.0
(c) 2004 Eletech Elnterprise Co. Ltd.
All rights reserved
* Hold-n-Tell is a trademark of Eletech Enterprise Co. Ltd..
Trouble Shooting
1. There is no sound.
a. Make sure the output level is turned up.
b. TurnontheinternalspeakerbypressingandlockingdowntheSpeaker
Button on case top. If the audio can be heard from the internal speaker,
butnot through the phone system, then makesure the audio patch cord
is properly connected.
c. If the audio can not be heard from the internal speaker, then the flash
card may have been installed without turning off the power. To fix this
problem, turn the power off for a few seconds.
2. It’s playing the wrong message.
Press the Change Button momentarily to advance to the next track. Re-
peat this process until the desired message is reached.
3. The sound quality is poor.
a. Wrong impedance was selected - change to the other value.
b. Output level is too high - turn it down with the VOL Dial.

Installation Guide
Step 1: Connect the unit.
Two different audio patch cords are provided. Use the one that fits your
phonesystem.Selecttheoutputimpedance (8 or 600 Ohm) that matches
your phone system. If you are not sure which one to choose, try both
settings and select the one with better sound quality.
Step 2: Install the flash card.
Theflashcardshouldhavebeen programmed
withaudiofiles before installation. Make sure
the power is off by turning the VOL Dial to-
ward the OFF direction till the power light
(on case top) is off. You can also unplug the
powercord if the VOL Dialhas beenadjusted
properly from previous use and you don’t
want to change it. Then slide open the flash
card cover and insert the card facing up. The
card should slide in with little effort. To remove the card, press the black
Eject Button.
Step 3: Turn on power and adjust output level.
Use the VOL Dial to turn on power and adjust output level. Audio playback
starts automatically. Press the Speaker Button (on cast top) to toggle the
internal speaker on and off. The internal speaker is for testing purpose only
and may be turned on or off during normal operation.
Step 4: Change tracks.
Up to 99 tracks can be programmed on the flash card. Press the Change
Button to go to the next track. If you go beyond the last track, it will
reset to the first track. You can also reset the unit to the first track at any
time by pressing down theChange Button for more than 2 seconds. DP-
200 remembers which track it was playing before power failure, and it
resumes that track automatically when power is restored.
Congratulationsonyour purchase of DP-200,thefirstCompactFlash based
16-bit on-hold system in the world offering the following features:
?100% digital design - no moving parts to wear and tear
?Works with any phone system with “external music” or “background
music” input
?Uses CompactFlash (CF) cards from 16MB to 512MB - more than an
hour’s audio can be stored if needed
?Windows .wav compatible
?Plays 16-bit uncompressed audio sampled at 11 or 22 KHz
?Up to 99 different tracks can be stored on a single flash card
?Switchable output impedance to match your phone system
?Built-in speaker for testing & monitoring purpose
?Desk top or wall mount
Whether it’s used to keep callers informed or entertained, DP-200 is an
efficient and cost effective tool that turns wasted hold time into pleasant
and valuable advertising time for your business.
Specifications
?Supported Sound File Format
Windows .wav, monaural output
16-bit uncompressed PCM sampled at 11 or 22 KHz
?Max. Number of Audio Tracks per Flash Card
99, switch selectable
?Audio Output Impedance
8 or 600 Ohm, switch selectable
?Supported Flash Card Type
CompactFlash card type I
?Physical Dimensions
Approximately 6.6” (L) x 4.5” (W) x 1.1” (H)
Package Content
1 x DP-200 Player Unit
1 x Power Adaptor
2 x Audio Patch Cords (one with 1/8” phone plug, one with RCA jack)
1 x User’s Manual
1 x Metal Mounting Plate
1 x CompactFlash Card (optional)