ELEXOL IP to Espa 444 Manual

Manual Ip to ESPA 444 converter Page 1 Date: 7 may 2013
Setup the
IP
to
Espa 444
Convertor.
Ip to Espa 444 Convertor
www.elexol.nl

Manual Ip to ESPA 444 converter Page 2 Date: 7 may 2013
Connect to the TCP/IP network 3
Connect to the ESPA444 equipment 4
Connect the power 5
Connect the output-relays 6
Opening the cab for the status leds 7
The status leds 8
Using the diagnoseport 9
Index

Manual Ip to ESPA 444 converter Page 3 Date: 7 may 2013
Connect to the TCP/IP network:
The TCP/IP network cable is connected to the RJ45 socket. As soon as the
connection is made, and the device is powered up, the green led lights up to
indicate the networkconnction.
More status information on the TCP/IP port can be found behind the cab on
the other side of the housing. See Page 7 of this document for further
explanation.

Manual Ip to ESPA 444 converter Page 4 Date: 7 may 2013
Connect to the ESPA44 equipment:
The convertor uses a standard 9p SUBD connector to connect to the ES-
PA444 equipment.
The pinlayout is:
Pin 2: TxD
Pin 3: RxD
Pin 5: GND
Pin 7: CTS
Pin 8: RTS
We stronly recommend to secure the RS232 cable to the housing using the
screw mounts.
More settings, like baudrate and more, are beïng setup via TCP/IP or the
RS232 diagnoseport. For further information see the associated document.
For status information about the communication via ESPA4.4.4. see page 7
of this document.

Manual Ip to ESPA 444 converter Page 5 Date: 7 may 2013
Connect the power to the converter:
The power supply of the Converter is 12V DC.
It is advised to use the power supply shipped with the con-
verter.

Manual Ip to ESPA 444 converter Page 6 Date: 7 may 2013
Connect the ouput relays:
1: Relay 1 Common
2: Relay 1 Normally Open
3: Relay 1 Normally Closed
4: Relay 2 Common
5: Relay 2 Normally Open
6: Relay 2 Normally Closed

Manual Ip to ESPA 444 converter Page 7 Date: 7 may 2013
Opening the cover to see the status leds and access the diagnoseport.
To open the cover, press it to the upward position (marked 1) and open it by
using a screwdriver on the top side of the cover (marked 2).
1 1
2

Manual Ip to ESPA 444 converter Page 8 Date: 7 may 2013
Status led indicators:
Status: Flashes short green each second:
The system is OK, no problems on TCP/IP or ESPA 444 side and no
calls in the buffer remaining.
zijde zijn en er geen oproep in het buffer staat.
Flashes long green each second:
The system is OK, no problems on TCP/IP or ESPA444 side, but calls are
available in the buffer.
Flashes short red each second:
An error is just detected.
Flashes short red continuous:
An error remains to long.
Flashes orange:
New settings are programmed. After a few seconds these new settings are
loaded into the converter, and the orange flashing stops.
Link: Flashes short each second:
The converter is waiting for a connection on TCP/IP side.
Lits up continuous:
The converter is connected via TCP/IP.
XML: Flashes on each recognised command via TCP/IP.
RxD: Flashes if data is received from the ESPA4.4.4. equipment.
TxD: Flashes if data is transmitted to the ESPA4.4.4. equipment.

Manual Ip to ESPA 444 converter Page 9 Date: 7 may 2013
The diagnoseport:
The diagnoseport is used to set up the Converter.
If needed, the Converter can be set up using the ConfigTool-IP. It is also possible to get diagnostic
information out of the converter in case of problems.
Connect the 9 pole subd to the laptop with a straight forward (1 on 1) 9 pole cable.