ELEY 1042 Programming manual

Free Standing Hose Reel
Model 1042
Assembly & Installation Instructions

Page 2
CONTENTS
123
456
7
8910
11
12
13 14
Reel Specications
Max. Temperature....140° F (60° C)
Max. Pressure.............150 PSI (10 Bar)
Please DO NOT contact or return this
item to the retailer. Seek assistance
directly from ELEY Corporaon using
the informaon below.
PHONE:
1-866-523-2363 (toll free)
MON- FRI, 8am to 5pm (CST)
E-MAIL:
[email protected]om
MON- FRI, 8am to 5pm (CST)
ONLINE:
The SUPPORT secon on our website
www.eleyhosereels.com is available
24/7/365 and contains assembly
videos, repair instrucons and FAQ’s.
QUESTIONS?
PROBLEMS?

Page 3
STEP 1
Place the Front
Flange (4027) on
top of the Back
Flange (4028).
Pins and sockets on
the anges will aid in
proper alignment.
IMPORTANT!
If you purchased an Extra-Capacity Kit
(Item# 1044) with your reel, please refer
to the assembly instructions included
with the Extra-Capacity Kit now. When
you have completed those instructions,
then proceed to Step 3 of this manual.
Standard Reel
Upgraded with
Extra-Capacity Kit

Page 4
STEP 2
Fasten anges together using the three
M6 x 20 Hex Socket Head Cap Screws
(4006) and the small hex end of the
Hex Key Wrench (4003).
STEP 3
Remove the screw from the
Handle Assembly (2654).
STEP 4
Install Handle Assembly
onto the Front Flange.

Page 5
STEP 5
Remove the two M10 x 25
Hex Socket Head Cap Screws
(4013) and 3/8” Flat Washers
(2520) from the Garden Hose
Reel Arm (3071).
STEP 7
Tighten the two M10 x 25
Hex Socket Head Cap Screws
(4013) and 3/8” Flat Washers
(2520) using the Hex Key
Wrench (4003).
STEP 6
Attach the Garden Hose Reel
Arm (3071) securely to the
Reel Base (2903) using the
two previously removed M10
x 25 Hex Socket Head Cap
Screws (4013) and 3/8” Flat
Washers (2520).

Page 6
Step 9
Install the Flange
Assembly onto the axle
with the crank handle to
the outside.
Step 8
Insert the externally
threaded (male) end
of the Inlet hose (1087)
into the axle tube until
it is accessible from the
other side.

Page 7
Step 11
Attach the Swivel
(2914) to the inlet
hose (1087).
Step 12
Attach the Swivel
to the axle. Hand
tighten rmly.
Step 10
Install the Cam-lever
Brake (2587) onto
the axle.
Note: Align the tab
on the brake with the
notch in the ange.

Step 13
Position the Hose Strap
(4045) 32 inches from the
internally threaded (Female)
end of your garden hose.
Page 8
Step 14
Position the Hose Strap
(4045) so the grommets
pass through the small slot
in the ange.

Step 17
Hand tighten your
garden hose to the
brass swivel.
Page 9
Step 15
Tighten the hose
strap. The M6 x 65
Hex Socket Head
Cap Screw (4009)
will pass through the
1/4 inch Flat Washer
(2331) and the two
brass grommets on
the hose strap and
then thread into the
cage nut on the reel
ange assembly.
Do not over tighten.
Step 16
Insert your garden
hose through the
large opening in
the reel ange.
Install the Anti-Kink
Spring (2367) into
the end of your
hose. The small end
rst.

Page 10
How to use the Cam-Lever Brake
As you pull the hose from the reel, our innovative cam-lever brake will
prevent the reel from “free-spinning”, unrolling more hose than you
want. The brake can be turned ON and OFF with the ick of the lever.
BRAKE ON
Pulling the hose out.
BRAKE OFF
Reeling the hose in.

Page 11
How to adjust the Cam-Lever Brake
1. Place the cam-lever in the “ON” position.
2. Pull enough hose off the reel to test the amount of drag created by the Cam-Lever Brake.
a. Too little drag, and the reel will continue to unspool hose after you’ve stop pulling.
i. Tighten the nut on the Cam-Lever Brake using a 3/8” wrench.
ii. Adjust 1/4 turn of the wrench.
ii. Test again.
b. Too much drag and it will be difcult to pull hose off the reel.
i. Loosen the nut on the Cam-Lever Brake using a 3/8” wrench.
ii. Adjust 1/4 turn of the wrench.
ii. Test again.

©2014 Eley Corporation PO Box 22640 Lincoln, NE 68542-2640 Rev. 04/14
Patents and Patents Pending (Manual Part # 4075)
Model: 1042 Serial # ____________________
Purchase Date:_________________________________
Purchased From:________________________________
10 Year Warranty
Coverage
Eley Corporation guarantees this hose reel, components and parts, unless otherwise specied,
to be free from defect, malfunction or failure in material, or workmanship, under normal use
and service, for a period of 10 years(120 months). Warranty period starts from original invoice
date. In the event of a defect or component failure, Eley Corporation will replace the specic
component(s) free of charge.
Exemptions
Warranty does not cover leaking due to damage caused by the use of acid, harsh chemicals
or mineral deposits. Warranty does not apply when products are used in excess of their
rated capacities and design functions or under abnormal conditions. The effects of corrosion,
and normal wear and tear are specically excluded from this warranty. This warranty does
not cover damage which occurs in shipment or failures which are caused by products
not supplied by the warrantor or failures which result from accidents, mishandling, faulty
installation, freezing, misuse or misapplication, abuse or neglect. Warranty is void if the
product or any part thereof has been tampered or altered in any manner, or damage that is
attributable to acts of God. Eley Corporation covers the replacement or credit of defective
parts only and does not allow for eld labor charges for removal, installation, analysis or
travel expenses. In no event shall Eley Corporation or its suppliers be liable for any damages,
whatsoever, arising out of the use of or inability to use this product. (Some states do not
allow the exclusion of limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you). Eley Corporation and its suppliers disclaim all
other expressed or implied warranties. Some states do not allow limitations on how long an
implied warranty lasts, so the above limitation may not apply to you. This warranty gives you
specic legal rights, and you may also have other rights which vary from state to state.