Elgato 4K60 User manual

U S E R M A N U A L
4K60 2x2 TV WALL CONTROLLER
Enjoy the vivid world!

Introduction
4K60 2x2 tv wall controller
The 2x2 tv wall controller , support 1-way HDMI input and 4 HDMI output, the main function is to
divide a complete HDMI,HD image signal into 4 blocks and assign to 4 video display unit (such
as Rear projection unit, LCD TV, etc.), Complete with 4 HDMI high-definition video display units
to form a large dynamic image screen.
Support modes

Features
*Support 1 HDMI input
*Support input HDMI 2.0
*Support 4 HDMI outputs
*Support input 4K60HZ,and lower resolution
*Support output resolution 1920x1080P60
*Support multiple splicing modes, easy to operate, plug and play
Physical interface diagram
OUTPUT → HDMI Signal Output
INPUT → HDMI Signal Input
SPDIF → Digital Audio Output
DC/12V → Power Adptor Input
IR → Remote Receiver
LED → Power Light
RS232 → RS232 Control
Audio → Audio ON or OFF
Mode → Different Mode Switch
→ Flip the picture under the mode of 2x2

Remote controller
Operation steps
STEP 1: Connect hdmi source to hdmi input with HDMI cable,connect hdmi
output to TVs.
STEP 2: Connect 12V power adaptor.
STEP 3: Set up splicing mode by the MODE button on the unit or remote
controller.

The Package includes
1. 2X2 tv wall controller x1
2. Power adapter x1
3. User Manual x1
Connection operation

RS232 remote control
This product supports RS232 remote command control and returns the status.Connect the RS232 port of the
splicer to the PC COM port by a Rs232 uncrossed cable or USB to RS232 adapter. Then install serial port tools
in the PC can use RS232 control.
Parameter configuration of serial port on PC side
Baud rate
115200
Parity bits
NONE
Data bits
8
Stop bits
1
Serial port command table:
NO
Send command
Return
ASCII
HEX
Instruction
Successful
Failul
1
!Sw0#
0x21 0x53 0x57 0x30
0x23
Switch to OFF mode
!Rc0#
NON
E
2
!Sw1#
0x21 0x53 0x57 0x31
0x23
Switch to 1X1 Spliced
mode
!Rc1#
NON
E
3
!Sw2#
0x21 0x53 0x57 0x32
0x23
Switch to 2X2 Spliced
mode
!Rc2#
NON
E
4
!Sw3#
0x21 0x53 0x57 0x33
0x23
Switch to 1X2 Spliced
mode
!Rc3#
NON
E
5
!Sw4#
0x21 0x53 0x57 0x34
0x23
Switch to 1X3 Spliced
mode
!Rc4#
NON
E
6
!Sw5#
0x21 0x53 0x57 0x35
0x23
Switch to 1X4 Spliced
mode
!Rc5#
NON
E
7
!Sw6#
0x21 0x53 0x57 0x36
0x23
Switch to2X1 Spliced
mode
!Rc6#
NON
E
8
!Sw7#
0x21 0x53 0x57 0x37
0x23
Switch to3X1 Spliced
mode
!Rc7#
NON
E
9
!Sw8#
0x21 0x53 0x57 0x38
0x23
Switch to4X1 Spliced
mode
!Rc8#
NON
E
10
!Sw9#
0x21 0x53 0x57 0x39
0x23
Backward loop switch
mode
!RCX#(X:0-8)
NON
E
11
!SWA#
0x21 0x53 0x57 0x41
0x23
Forward loop switch
mode
!RCX#(X:0-8)
NON
E
12
!SWB#
0x21 0x53 0x57 0x42
0x23
Standby
!RcB#
NON
E
13
!SWC#
0x21 0x53 0x57 0x43
0x23
Power on
!RcC#
NON
E
14
!SWD#
0x21 0x53 0x57 0x44
0x23
Turn on the OSD show
!RcD#
NON
E
15
!SWE#
0x21 0x53 0x57 0x45
0x23
Turn off the OSD show
!RcE#
NON
E
16
!COM#
0x21 0x43 0x4f 0x4d
0x23
Reads current state
Power state/
OSD state/
Display mode
e.g.!RCC#!
RCE#!RC2#
NON
E