elink LNK-GY10GP-SFP User manual

LNK-GY10GP-SFP
Quick Installation Guide
V1.0

1. Package list
LNK-GY10GP-SFP
2. Hardware Introduction
2.1 Physical Di ensions
 Dimension: 107mm (L)*77mm (W)*37.5mm (H)
 Weig t: 270g
 Operating temperature: -10 ℃ ~65 ℃
 Storage temperature: -20 ℃ ~ 85 ℃
 Humidity: 5% ~ 95% RH Non-condensing
 Maximum power consumption: 4.36w (PoE wit out load)
2.2 Front Panel
T e front panel of t e LNK-GY10GP-SFP contains 1*port 10000Base-T RJ45
interface wit IEEE 802.3bt PoE++ injector function, 1*port 10GBase-X SFP+
interface .

3.3 Rear Panel
T e Rear panel is s own as below:
2.3 LED Indicators
Label Type Color State Description
P 1/2 Power Status Green
On Lig ts to indicate t e power is on
Off Indicate t e power is off

Fault Fault Alarm Green
On Power fault alarm
Off T e Power is normal
10G
10G Et ernet link
status
Green
On Lig ts to indicate t e port is link up
Off Indicates t at t e port is link down
Yellow
On Lig ts to indicate t e PoE++ is in
use
Off Indicates t at t e PoE++ is not in
use
10G
SFP+
10G SFP+ link
status Green
On
Lig ts to indicate t e optical
module in place on t e premise
t at t e 10G Et ernet link is up
Off Indicates t at t e optical module
not in place
3. Hardware specifications
Label Description
10G
1 * 100M/1G/2.5G/5G/10G Base-T RJ45
Auto-MDI/MDI-X auto-negotiation
10G SFP+
1 * 10GBase-SR/LR SFP+ interface
Connector
Removable 6-pin terminal block
Pin 1/2 for Power 1, Pin 3/4 for fault alarm, Pin5/6 for
Power 2. DC Input:44-57V

4. Application Diagram
Long Reac POE solution is designed to extend IP Et ernet transmission and
inject power into a remote 802.3af/at/bt PoE compliant power device (PD)
beyond t e 100 meters limit of Et ernet.
Note
Before installation,please consider t e distance and watts value
demand for PD devices.
Typical Application:
T e LNK-GY10GP-SFP is powered via t e external power. An IEEE 802.3af/at/bt
compliant PoE PD will automatically be powered by t e LNK-GY10GP-SFP via UTP.
10G
Single Mode Fiber 10GE
10G+PoE Cat6A/7 UTP Cable 10GE with PoE++( p to 90w)
Power Line DC
10G
10G+PoE
5. Mounting Procedures
T e LNK-GY10GP-SFP can be mount installed on a c assis/wall, t ere are 2 angers
on t e rear panel of LNK-GY10GP-SFP wit s ipment for mount installation as
following picture s ows:

Hangers for Installation
Hangers for InstallationHangers for Installation
Hangers for Installation
Rear Panel
Rear PanelRear Panel
Rear Panel
Step1. Remove four mounting fin screws on t e back panel as s own below.
Tighten the screws
Tighten the screws Tighten the screws
Tighten the screws (
((
(screw standard
screw standardscrew standard
screw standard:
::
:M
MM
M3
33
3*
**
*4
44
4)
))
)
Rear Panel
Rear PanelRear Panel
Rear Panel
Step2. Turn over t e fins and restore t e four screws back to t e back panel as s own
below
Step3. For brick and cement wall, place t e LNK-GY10GP-SFP to t e proper location
w ere it is going to be installed, use a marker or pen to identify t e ole locations

Step4. Follow t e marked ole location, drill four oles using 6mm drill tip and nail in four
plastic wall-mount nuts into t e oles, t en mount t e LNK-GY10GP-SFP on t e wall
wit four wall-mount screws.
For t e wall or location w ere t e screws can be screwed in directly, t e
LNK-GY10GP-SFP can be mounted wit four wall-mount screws wit out t e need of
plastic wall-mount.
Warming
Must use t e M3*4 standard screws to tig ten t e angers
6.Appendix A RJ45 Pin Assignments
RJ45 Pin Assignments
Contact POE
1 Negative(VCC-), Pair 1
2 Negative(VCC-), Pair 1
3 Positive(VCC+), Pair 1

4 Positive(VCC+), Pair 2
5 Positive(VCC+), Pair 2
6 Positive(VCC+), Pair 1
7 Negative(VCC-), Pair 2
8 Negative(VCC-), Pair 2