Elite Industries EL-147N User manual

CABINET PARTS
1. Bottom Panel
2. Top Panel
3. Left and Right Side Panels
(identical)
4. Center Vertical Support
5. Left and Right Vertical
Mouldings (identical)
6. Two Adjustable Shelves
7. Back Panel (2 identical parts)
8. Two Glass Doors
ALIGN
CAMLOCK &
CONNECTING
BOLT
JOIN PIECES
TOGETHER
ARROW WILL NOW
BE AWAY FROM
THE EDGE ON THE
OPPOSITE SIDE.
TURN CAMLOCKS
180° CLOCKWISE
USING A FLATHEAD
SCREWDRIVER
1
23
PLEASE DO NOT RETURN UNIT TO STORE FOR PARTS & CUSTOMER SERVICE.
PLEASE CALL 1-800-ELITE-48. CUSTOMER SERVICE HOURS EASTERN TIME 8:45 AM - 4:30 PM M-F
VISIT OUR WEBSITE AT: www.elite-inds.com
Thank you for purchasing this Elite product. You will need the following tools:
Phillips Head Screw Driver • Straight Blade Screw Driver • Rubber Padded Hammer or Mallet
ASSEMBLY INSTRUCTIONS
TV STAND:
Model EL-147N
Black Matte Melamine
OVERALL DIMENSIONS:
18-1/2" H x 47" W x 17-1/2" D (Top), 19" D (Bottom)
477445 Page 1/4 08.30.10
D2
Magnetic
Touch Latch
E4
BLACK
1/2" Wood Screws for
Magnetic Touch Latch
F 16
Camlocks
G 16
BLACK
5/8" Screws for
Back Panel
H8
1" Long Shelf Pin
J 16
Plastic Camlock
Covers
K 16
Wooden Dowels
N
22
8
Glass Door Hinges
P4
Protective Plates
Q2
Metal Strike Plates
R2
Foam
Protective Pads
S4
Plastic Bushings
Hardware for Unit Assembly
IMPORTANT NOTES & CAUTIONS/WARNINGS
•Carefully read and follow these instructions for assembly.
•Please handle parts carefully, some parts may be heavy and can have sharp edges –
we recommend possibly using cloth protective gloves for extra protection.
•To protect the unit and your flooring surface we recommend working on a padded
or carpeted area, you may also use the open box the unit came in for this purpose.
•For proper construction & integrity/assembly and for TV weight support and safety,
all connections need to be sufficiently tight. However, do not over-tighten
connections to the point of stripping screw threadings. Parts are designed to fit
together tightly, however, avoid excessive force but rather align & fit panels together
methodically and with patience.
•For some heavy or large units, it may be recommended for 2 people to work
together on this assembly.
•It is extremely important to attach the BACK PANEL as instructed within this manual.
Such panels are crucial for the stability and structural support of the unit.
•Please read additional important safety information at the end of this
instruction manual.
•We urge you to keep this manual with your unit for future reference.
SPECIAL NOTE: In all steps
involving camlocks, please note the
correct position of the camlock in
the illustration at the left. Check all
camlocks before aligning and join-
ing pieces together. IMPORTANT:
Throughout assembly of the unit,
camlocks must be inserted with
the ARROW FACING THE EDGE.
CAMLOCK/
CONNECTING
BOLT
PROCEDURE
8
8
2
7
7
3
4
3
66
1
5A5
Casters
B 20
CHROME
3/8" Wood Scews
for Casters
C 16
Connecting Bolts
18-1/2"
17-1/2"
19"
47"
14-1/8"
21-3/8"
15-1/8"
5

2 TOP PANEL PREPARATION WHEN INSERTING
CONNECTING BOLTS
DO NOT OVERTIGHTEN
ABC
C
E
1
1
UNDERSIDE
2
UNDERSIDE
FRONT EDGE
Turn Top Panel (2) over to expose the underside.
Attach 2 Magnetic Touch Latches (D) to the FRONT EDGE
using 4 Screws (E). Magnets must face front.
Attach 6 Connecting Bolts (C) into the
pre-installed small plastic threaded holes
as indicated.
DO NOT OVER TIGHTEN.
3 SIDE PANELS PREPARATION 4CENTER VERTICAL
SUPPORT
PREPARATION
SPECIAL NOTE
Camlocks must be inserted with the arrow
facing the nearest unfinished edge.
Insert 4 Wooden Dowels (K) into top and bottom
edges of RIGHT Side Panel (3).
Insert 4 Camlocks (F) into top and bottom edges
of RIGHT Side Panel (3) PLUS 2 Camlocks (F)
into Front Edge as shown.
Insert 4 Wooden Dowels
(K) into top and bottom
edges of Center Vertical
Support Panel (4).
Insert 4 Camlocks (F) into
top and bottom edges of
Center Vertical Support
Panel (4).
Insert 4 Wooden
Dowels (K) into top
and bottom edges
of LEFT Side
Panel (3).
Insert 4 Camlocks
(F) into top and
bottom edges of
LEFT Side Panel (3)
PLUS 2 Camlocks
(F) into Front Edge
as shown.
FRONT
EDGE
BACK
EDGE
BACK EDGE
FRONT
EDGE
3
3
4
F
K
K
K
K
K
K
K
K
K
K
K
K
F
F
F
F
F
F
F
1BOTTOM PANEL
PREPARATION
WHEN INSERTING
CONNECTING BOLTS
DO NOT OVERTIGHTEN
DD
5 VERTICAL MOULDINGS PREPARATION
Insert 2 Wooden Dowels (K)
into top and bottom edges of each
Vertical Moulding (5).
Insert 2 Connecting Bolts (C) into each
Vertical Moulding as shown.
5
5
K
K
K
K
C
WHEN INSERTING
CONNECTING BOLTS
DO NOT OVERTIGHTEN
477445 Page 2/4 08.30.10
Turn Bottom Panel (1) over to attach 5 Casters (A) to the
underside using 3/8" Screws (B).
Turn Bottom Panel (1) over. Attach 6 Connecting Bolts
(C) into the pre-installed small plastic threaded holes as
indicated. DO NOT OVER TIGHTEN.
FINISHED FRONT EDGE

6 ATTACH MOULDINGS TO SIDE PANELS
Align the Connecting Bolts of Right Vertical Moulding
(5) with the corresponding holes of Right Side Panel (3).
Join together. Turn 2 corresponding Camlocks (F) 180°
to lock.
Align the Connecting Bolts of Left Vertical Moulding (5)
with the corresponding holes of Left Side Panel (3).
Join together. Turn 2 corresponding Camlocks (F) 180°
to lock.
FOLLOW CAMLOCK/CONNECTING
BOLT PROCEDURE BELOW.
55
3
3
7 ATTACH SIDE PANELS AND CENTER VERTICAL SUPPORT PANEL TO TOP AND BOTTOM PANELS
5
5
4
2
1
3
3
Align the Connecting Bolts of Bottom Panel (1) to the
corresponding holes of Right and Left Side Panels (3)
and Center Vertical Support Panel (4). Be sure that the
Wooden Dowels of Right and Left Side Panels and Center
Vertical Support Panel also align with the corresponding
holes of Bottom Panel (1). Join pieces together.
FOLLOW CAMLOCK/
CONNECTING BOLT
PROCEDURE SHOWN
AT THE LEFT.
Align the Connecting
Bolts of Top Panel (2)
to the corresponding
holes of Right and Left
Side Panels (3) and
Center Vertical Support
Panel (4). Be sure that
the Wooden Dowels
of Right and Left Side
Panels and Center
Vertical Support Panel
also align with the
corresponding holes
of Top Panel (1).
Join pieces together.
TURN CAMLOCKS
180° CLOCKWISE TO
LOCK PIECES TOGETHER.
1
ALIGN
CAMLOCKS
WITH
CONNECTING
BOLTS
2
JOIN PIECES
TOGETHER
3TURN CAMLOCKS
180° CLOCKWISE USING A
FLATHEAD SCREWDRIVER.
THIS WILL LOCK
THE 2 PIECES TOGETHER
CAMLOCK
CONNECTING BOLT
PROCEDURE
8J
ADD CAMLOCK COVERS
ADD CAMLOCK COVERS (J) TO ALL LOCKED
VISIBLE CAMLOCKS
5
6
6
4
2
1
3
3
Insert 4 Shelf Pins (H) in the desired holes for each Shelf (6). Place each
Shelf (6) inside unit from the back.
H
H
HH
H
10 ATTACH BACK
Attach Back Panel (7) to unit fitting it inside
groove at back of unit and securing it with 5/8"
Wood Screws (G).
GG
7
7
477445 Page 3/4 08.30.10
9 ADD ADJUSTABLE SHELVES

11 ADD GLASS DOORS
Insert 4 Plastic
Bushings (S)
into holes in
Bottom Panel
(1) and under-
side of Top
Panel (2).
Insert 2 Glass
Door Hinges
(N) into
Bushings (S)
of Bottom
Panel (1) as
indicated.
Add 2 Glass
Door Hinges (N) to
Glass Doors (8)
slipping Protective
Plates (P) between
glass and hinge
setting screws.
Insert Glass Door into Bushing in Top Panel and
slide into hinge at bottom. Tighten set screws at
top and bottom.
NOTE: If doors overlap, loosen setting screws and slide
door in hinge as needed. Make sure setting screws stay
in contact with protective plates when tightened,
Remove paper backing from Foam Pad (R) and
attach/wrap over top inner corner of door. Slide metal
Strike Plate (Q) over pad.
Repeat for second door.
S
S
S
S
N
P
R
Q
IMPORTANT NOTICE
Top Panel, Part #2 is designed to be used with TV's and other A/V equipment NOT weighing more than 176 lbs.
The loading weight needs to be evenly distributed across top panel and for optimum stability,
Place TV in a center position on Top Panel, not unbalanced to the side against edge for example.
If the TV’s supporting legs on the left & right are naturally situated directly above location of supporting
Side Panels (3), you may then load up to 198 lbs. maximum on Top Panel (2).
Also: Note dimensions for Top Panel Surface as listed at the beginning of this manual and
read the following "Important Safety Precautions".
Bottom Panel, Part #1 is divided into two separate compartments. Each side is designed to be used with A/V
components NOT weighing more than 55 lbs. per compartment.
Adjustable Shelves, Part #6, are designed to be used with A/V components
NOT weighing more than 22 lbs. per shelf.
HOWEVER, for the total unit loading capacity, DO NOT exceed a total of 290 lbs.
IMPORTANT SAFETY PRECAUTIONS
Please carefully read & follow these important safety information notes for proper use of the furniture you have just assembled. They are designed to avoid unsafe conditions that can
result in property damage, bodily injury or death. We therefore urge strict adherence to the following basic principals:
• Install this unit on a flat & level surface only.
• Avoid placing unit in direct sunlight or near heating source. We recommend not placing unit directly against wall but rather leaving a narrow space between unit and wall for proper
ventilation of your A/V equipment.
• Do not exceed the above recommended weight loading limits as this can result in sagging or structural failure of the supporting panel leading to unsafe conditions.
• TV screen sizes are measured diagonally, therefore, base foot-print size for specific TV’s can not be determined by screen size as they vary from manufacturer to manufacturer. Rather
you will need to measure the TV’s base foot print and compare it to the top panel surface size of your furniture as listed in this manual.
• Make sure to place TV within the surface area of the top panel, a bit inward from the front edge and centered. Never use with a TV that is too large. The TV base foot print surface
must be able to sit completely on the top panel surface.
• When choosing locations for stacking A/V components on shelves, make sure to place the heaviest A/V equipment on the lowest possible shelves/bottom panels first.
• Children should
never be allowed to climb on or play with this furniture or/and the TV. This can result in an unsafe situation which may lead to the TV and/or the furniture itself to
become unsteady, slip, tip or fall over. Avoid using higher shelves or the top surface of the TV for objects that may tempt children to reach and climb. Such items can include toys,
food, as well as remote controls, etc. Proper supervision and common sense is always required.
• Glass doors are “Tempered.” This is a special process for achieving strength and safety. Although durable & solid we recommend avoiding bumping into glass with force or dropping
or chipping edges etc. Special caution should be given to glass corners, both, for protection of glass as well as most importantly to avoid the possibility of injuries resulting from
strong impacts against corners especially with children. Doors should be opened & closed gently. (Tempered glass is designed to shatter upon very strong impact and rather than
producing sharp knife-like dangerous edges, it turns instead into small pebble-like pieces.)
• Moving the unit:
The strong caster wheels on this unit are intended for normal short-distance indoor use only, not for rough floor surfaces or outdoor use. Do not drag unit
when moving and especially be careful not to move unit on a carpeted surface or on a rug if it may pose resistance for caster mobility. If conditions are such, it is always
recommended instead to lift unit from both ends with a friend’s help. For the sake of safety and to avoid damages, we recomend you move the TV and all A/V components
prior to moving this unit. If this is not possible please use much caution and good judgement and seek help to ensure stability and safety as the unit is being moved. Make
sure afterwards to properly re-adjust all equipment, centered and stable as originally instructed above.
Congratulations and enjoy your new ELITE product!
To clean your unit, apply window cleaner with soft tissue. This will also eliminate slight surface abrasions
or scratches that may have occurred in shipping or handling.
Distributed by: Elite Industries, 77 Gould Street • Bayonne, NJ 07002, Tel.: [phone] • Fax: [phone]
Elite Industries ensures complete satisfaction with this product. In the event of missing or damaged parts call toll free,
Customer service hours: 8:45-4:30, Monday-Friday, EST., 1-800-ELITE-48 •
VISIT OUR WEBSITE AT: www.elite-inds.com
N
N
477445 Page 4/4 08.30.10