Elite Screens Yard Master Plus Series User manual
Rev.07032023 wwww.elitescreens.com
Yard Master Plus
Ser
i
es
Indoor/Outdoor Portable Projection Screen
User’s
Guide
Thank you for choosing the Yard Master Plus portable projection screen! Please read through this user guide
before utilizing the screen. Correct usage and maintenance will ensure a long product life.
Care & Use Instructions
◆Elite Screens highly recommends two people to assemble the Yard Master Plus screen.
◆Dust, dirt and scratches on the projection surface will affect the picture quality, please take note of the points
below to prevent that from occurring:
1. Do not touch the projection surface with your hands
2. Do not write or draw on the projection surface
3. Do not use fingers or sharp objects to point on the projection surface; this will damage the screen
material.
4. Use a soft-damp cloth to clean the projection surface; do not use chemical cleaning agents or
alcohol.
5. Use clean water when dampening the cleaning cloth and do not rub against the material to clean it.
◆After using the screen, disassemble it and store it in the carrying bag provided.
◆To avoid damage and injury, the screen should only be operated by adults.
Product Description
Design: The aluminum frame is designed to be light weight and easily operated making it easy to carry,
assemble and disassemble.
Screen Fabric: The screen fabric is attached to the rectangular frame and held in place by several press stubs,
which ensure an evenly stretched and flat surface. The CineWhite® (front projection) screen material is durable
and can be folded many times without causing damage or distortion to the surface.
Correct usage of the projection screen will ensure better viewing results.
For front projection, assemble and view the screen as indicated in Fig.1.
Rev.07032023 wwww.elitescreens.com
Hardware and Parts List
A. Folding frame x1
B. Left and right folding legs x2
C. Knob Screw (Refer to Chart)
D. Projection screen material x1
E. Screen material bag x1
F. Carrying Bag x1
G. Rope
H. Eyebolt x 2
I. Ground stake x 4
Note: The parts list above is subject to change without notice.
Frame Assembly
1. Take the folding frame (A) out of the carrying bag (F) and place it on a flat surface. Fully unfold the longer
sections first, as shown below.
2. Next, unfold the frame until the latch on the hinge “clicks” into place. Repeat the procedure for the shorter
sections, as shown below.
Models
Knob Screw
Support Leg
Max Height
100”(16:9)
12 pcs
Included
95.5 inches
120”(16:9)
12 pcs
Included
112.2 inches
135”(16:9)
10 pcs
Included
113 inches
145”(16:9)
10 pcs
Included
133.5 inches
180”(16:9)
10 pcs
Included
159.8 inches
200”(16:9)
14 pcs
Included
149.6 inches
Rev.07032023 wwww.elitescreens.com
Note: When unfolding the frame and legs, be sure the latches on the hinges "click" into place. Please also make
sure all 4 corners of the frame are at a 90° angle and the hinged support bar is straight and not bent.
Screen Material Attachment
1. Take the screen material (D) out of the screen material bag (E) and align the corners of the screen
material with the inside corners of the frame.
2. Once the screen material is fully extended, secure the material by snapping the buttons onto the frame
studs. Fasten the buttons in the following order as shown on Fig.1.
Note: Snap the buttons on each corner first, then work your way out to the center on each side.
5
1 3
7 8
4 2
6
Fig.1
Rev.07032023 wwww.elitescreens.com
Leg Attachment for 100”/ 120”Models
1. Carefully take the left and right folding legs (B) out of the carrying bag (F) and place it on a flat surface. Unfold the
left and right legs leaving the front foot folded as shown below. Make sure the hinges click into place.
Warning: The additional support sections, located at the middle section of the legs, may unfold on its own. Please be sure to use
caution while removing/placing the legs from/to the bag
2. Once the legs are unfolded, lay the frame on the floor and position the legs over both sides of the frame.
Use the knob screws (C) to attach the frame to the legs.
Warning: When attaching the legs, make sure to screw the top of the leg to the last hole of the frame to reach max height.
Attaching the legs lower to the frame and leaving an extra space on top may cause the screen to tip over when assembled.
3. After making sure the legs are secure to the frame, using two people, lift the screen up in a vertical position. While
the screen is in a vertical position, fold the front feet of the legs out.
4. The assembly is now complete, and the projection screen will be stable on a flat surface.
Leg Attachment for 135”–200”Models
1. Starting from step 2 on the previous procedure, lay the frame on the floor and
position the legs over both sides of the frame. Use the knob screws (C) to attach the
frame to the legs.
Warning: When attaching the legs, make sure to screw the top of the leg to the last hole of
the frame to reach max height. Attaching the legs lower to the frame and leaving an extra
space on top may cause the screen to tip over when assembled.
Rev.07032023 wwww.elitescreens.com
2. Next, carefully unfold the extra support leg behind the leg and attach it securely using a knob screw (C). Then repeat
steps 3 and 4 on the previous procedure.
Height adjustable frame feature
The Yard Master Plus allows for the main frame to be set at various height settings at 5.9” intervals.
Step 1: Lay the frame on a clean sheet to avoid damaging the projection surface. Then lay the legs over on the back of the
frame in the position desired.
Step 2: Once you have aligned the leg’s holes with the frame’s holes, secure with the knob screws.
Screen Disassembly
1. After using the screen, disassemble and store it in the carrying bag (F). To disassemble the screen, follow the
assembly procedure in reverse order.
2. Store the screen in the provided carrying bag (F). Be sure to place folding frame, legs, and smaller parts into the
carrying bag first and place the material on top to keep material from creasing or tearing.
Location points for legs
Table of contents
Other Elite Screens Projector manuals
