Elite Pull-Out Pantry 400MM User manual

Pull-Out Pantry
Installation Instructions
for 400MM and 450mm width cupboards
Features
o Stainless Steel
trays
o Soft Close
o Adjustable frame
height
o Adjustable tray
positions
o Door position
adjustments
Cabinet
Dimensions
400mm$
Width$
Model$
450mm$
Width$
Model$
Width$
(external)$
Suits&
400mm&
standard&
width&
cupboard&
Suits&
450mm&
standard&
width&
cupboard&
Width$
(internal)$
Minimum&
of&365mm&
Minimum&
of&415mm&
Height$
(internal)$
Adjustable&
1700mm&to&
2000mm&
Adjustable&
1700mm&to&
2000mm&
Depth$
(internal)$
Minimum&
of&482mm&
Minimum&
of&482mm&

Pull-Out Pantry
Installation Instructions
for 400MM and 450mm width cupboards
1
4
3
6
2
5
7
Listing of key parts
 1 x Top Runner
 1 x Bottom Runner
 1 x Main Frame
 2 x T-Bar
 2 x Saddle Backed Stabiliser
 12 x Basket Anchor
 6 x Stainless steel basket
Listing of fixing hardware
28 x ST4*14 Pan Head
Screws
! 8 pcs for fixing Top
Runner to cabinet ceiling
! 8 pcs for fixing bottom
runner to cabinet floor
! 12 pieces for fixing T-Bar
to door
8 x ST4*14 Countersunk
Head Screws
! 8 pcs for fixing Saddle
Backed Stabilisers to door
6 x M6*15 Hex Bolt
! 6 pcs for fixing T-Bar to
Frame
2 x M8*20 Hex Bolt
! 2 pcs for adjusting
position of door
! Supplied affixed to Frame
base
2 x M6*10 Hex Bolt
! 2 pcs for adjusting height
of Frame

Pull-Out Pantry
Installation Instructions
for 400MM and 450mm width cupboards
Step One – Fix Bottom Runner
 Position runner on centre axis of cabinet floor 15mm from front edge
 Ensure the runner is square with cabinet and centred
 Securely fix with 8 x ST4*14 Pan Head Wood Screws
 Check that when runner is pulled out it engages with the soft close
mechanism
mm&
Step Two – Fix Top Runner
 Position runner on centre axis of cabinet ceiling 15mm from front edge
 Ensure the runner is square with cabinet and centred
 Securely fix with 8 x ST4*14 Pan Head Wood Screws
mm&

Pull-Out Pantry
Installation Instructions
for 400MM and 450mm width cupboards
Step Three – Fix Frame to Bottom Runner
 Loosen two Riser Anchor Nuts (A) on the Bottom Runner with hex key
 Place Frame holes (B) on riser anchor nuts (A) and slide towards front so
Riser Anchor Nuts (A) are visible through the Frame holes (B)
 Adjust Frame position so its front is aligned with front of cabinet
 Tighten Riser Anchor Nuts (A) through Frame hole (B) with hex key so
Frame is affixed firmly to Bottom Runner
 Ensure M8*20 Adjustment Bolts (E) are in place in Frame hole (D) for
later door adjustment
B
B
A
A
Bottom Runner
Frame Base
(underneath)
Fixing and
Adjustment
B
Front
Front
Front of
Frame has
three
fixing
holes on
side of top
and
bottom of
Frame
D
D
D
E
1
2
4

Pull-Out Pantry
Installation Instructions
for 400MM and 450mm width cupboards
Step Four – Fix Frame to Top Runner
 Ensure Top Runner is fully assembled with Top Runner Anchors (A)
 Remove rubber rings from Top Runner Anchors (A)
 Slide top of Frame (B) up so the Top Runner Anchors (A) insert through
the holes in the top of the Frame
 Fasten the height of the top of Frame (B) in place with 2 x M6*10 (C).
The top of the Frame should be about 2mm from the Top Runner.
 Replace the rubber rings over the Top Runner Anchors (A)
B
A
A
Fix to
Top
Runner
C
1
Fasten
Frame
4

Pull-Out Pantry
Installation Instructions
for 400MM and 450mm width cupboards
Step Four – Fix Frame to Cabinet Door
 Fix each T-Bar (A) to Door with 6 x ST4*14 Pan Head Screws. Position T-
Bars as per diagram
 Fix 2 x M6*15 Hex Bolts onto Top T-Bar and Bottom T-Bar as per diagram
 Slide T-Bars (A) into frame until the Hex Bolt heads are visible and
aligned with the side holes of Frame
 Fix a M6*15 Hex Bolt (B) through the middle side hole of Frame for the
Top and Bottom T-Bar (you may need a friend to hold the door steady)
 In the next step you can adjust the door position to align with cabinet
Fix T-Bars to Door
1
Line of
inside of
cabinet
Door
Centre line
32mm
81mm
Insert T-Bars into Frame
2
Screw 2 x
M6*15 into
left and
right holes
of each
T-Bar
Insert T-Bars
into Frame and
then screw
1 x M6*15 (B)
into middle
hole of Top and
Bottom Frame
into each T-Bar
3 4
The T-Bars should
have 2 x M6*15 bolts
affixed before
inserting in the Frame.
These are used in a
later step to align the
Door
Once completed,
the left and right
bolt heads are
inside the Frame.
The middle bolt
head is outside
the Frame
A
A
A
A
B
B

Pull-Out Pantry
Installation Instructions
for 400MM and 450mm width cupboards
Step Five – Door Alignment and Stabilisation
 Horizontal Door Adjustment: Loosen (but do not remove) the middle
Hex Bolt on Top and Bottom T-Bars (A) (see Step 4). Then use the left
and right Hex Bolts (B) to position the Door horizontally. When the
horizontal position is correct, tighten the middle Hex Bolts to fasten the
Door to the Frame
 Vertical Door Adjustment: Loosen (but do not remove) the Riser Anchor
Nuts (C) (see Step 3) on the Base Runner. Then use the M8*20
Adjustment Bolts (D) (see Step 3) to position the Door vertically. When
the vertical position is correct, tighten Riser Anchor Nuts (C).
 Affix Saddle Backed Stabilisers: (Note: You may wish to do this after
Step 6 so the position of the Stabilisers does not interfere with the pantry
baskets.) Affix the two Saddle Backed Stabilisers (E) over the Frame
front vertical bar to the Door to stabilise the Door using 4 x ST$*14
Countersunk Head Screws for each Stabiliser
Vertical Door Adjustment
2
Horizontal Door Adjustment
1
A B
B
C C D
D
Affix Stabilisers
3
E
E

Pull-Out Pantry
Installation Instructions
for 400MM and 450mm width cupboards
Step Six – Installation of Pantry Baskets
 Clip Basket Anchors to Baskets: Carefully attach the Basket Anchors (A)
to the Baskets as per the diagram
 Clip Baskets to Frame: Carefully attach each Basket to the Frame by
first inserting one attached Basket Anchor into the Frame and then
gently lowering or raising the other side carefully until its Basket Anchor
clips in. Do not force the Baskets into place – they should be gently
inserted one side at a time and the other side raised or lowered until it
clips into place.
Carefully insert
Baskets into
Frame on an
angle. Clip
Anchor in one
side, then gently
lower or raise the
other side until it
clips in – do not
force the Baskets
into place.
Clip Anchors to Baskets1 Clip Baskets to Frame2
Carefully clip each Basket Anchor (A) onto
the Anchor cavities on each Basket. Do
not use force – gently clip it on.
A
A
With the Basket Anchors clipped on, the
Basket is ready to attach to the Pull Out
Pantry Frame.