EliteProAV Tab-Tension Pro Series User manual

11262019JA www.eliteproav.com 1
3
2
4
Fig.1
Fig. 2
Tripod Tab-Tension Pro Series
Portable Tripod Tab-Tensioned Projection Screen
For models: CineWhite UHD-B (matte white) and
CineGrey 5D®(Ceiling Ambient Light Rejecting)
USER’S GUIDE
Tripod Screen Parts Identification
A. Tripod Screen Setup
Follow the steps below and Fig. 1 & 2.
1. Place the screen in an upright position (Fig.1) with the 1
legs toward the ground.
2. Deploy the Tripod Support legs by pushing
downon the Tripod Junction.
3. Turn the tripod’s screen case in a 90-degree
horizontal position so that the screen casing is
now parallel to the ground with the screen handle
facingthe bottom of the top hook.
4. Completely extend the legs as much as possible
so they are stable and position them away from
objects that may interfere with their balance. DO
NOT stand the tripod on an unstable platform to
avoid an injury should the tripod screen collapse.
Tripod drape skirt

11262019JA www.eliteproav.com 2
1
3
4
B. Preparing the tripod screen forprojection:
Follow the steps below and Fig. 3.
1. Pull the screen handle up vertically and hook the screen handle on
the Top Hook.
2. Push/press the Vertical Locking Tab to unlock the current
position of the Vertical Extension Bar and raise it with another
hand. Remain pushing on the button until you reach the desired
height and let go until you hear a click sound which indicates it is
locked in place.
3. Push/press the Screen Height Adjustment Lock/Release
located just above the Carrying Handle to raise or lower the
bottom ofthe screen. Once the desired height has been set, let go of
the tab to lock the position in place.
Tripod Skirt Installation
4. Unfold the tripod skirt in a clean area. Use the magnetic bars to attach it to the tripod case.
C. Collapsing thescreen:
Follow the steps below and Fig. 4.
1. Push/press the Screen Height Adjustment Lock/Release to unlock and
slowly slide the handle all the way up to slowly retract the screen into its
case.
2. Unhook the screen material from the Top Hook and slowly retract the
screen back into the case.
3. Once the material is in its case, Push/press the Screen Height
Adjustment Lock/Release to unlock and slowly slide the handle all the way
down to bring down the position of the screen’s case.
4. Hold the Extension Bar and Push/press the Vertical Locking tab to unlock and
releasethe position of the extension bar. Bring the extension bar all the way down.
5. Turn the screen’s case vertically clockwise and insert the TopHook’s
bottom pin to lock into the screen’s end cap hole.
6. Close the tripod legs by pushing them in.
Note:
•To ensure the screen is stable, extend the tripod’s legs as muchas possible.
•Do not fold the screen or allow any sharp objects to touch the screen’ssurface.
•Clean the screen surface often whenneeded.
•Careful use will extend the lifetime of thisproduct.
For more information, technical support or your local Elite ProAV contact,
please visit www.eliteproav.com
Fig. 3
Fig. 4
1
2
3
2
Note: It is very important to remember to hold the extension bar first and then unlock
the adjustment tab to prevent the extension bar from slamming and causing injury or
damaging the screen.
Note: Use the Keystone Eliminator to prevent “Keystone Effect” from
occurring. Keystone Effect is caused when a projector presents its image
at a downward angle causing a trapezoid-shaped image to appear on the
screen. The Keystone Eliminator is designed to eliminate that effect by
sloping the screen forward.

11262019JA www.eliteproav.com 3
Notice to Installer:
Please use the following installation instructions to obtain superior optical performance from the CineGrey 5D®
Angular Reflective CLR®/ALR (Ceiling Ambient Light Rejecting) Screen
Make sure to follow these instructions in order for the CineGrey 5D®to perform correctly.
1. Ambient Light must not come from the same direction as the projector’s light
2. Minimum Lens Throw Ratio of 0.8 x image width
3. Compatible with Short Throw projector with a 0.8 lens throw equal or greater
4. Not compatible with Ultra Short Throw Projectors