eliving FURNITURE CHB-0554PCSGRY User manual

NOTE: 50% TIGHTEN BEFORE FIXING ALL BOLTS
ASSEMBLY INSTRUCTION
Item NO.: CHB-0554PCSGRY
CHB-0554PCSBLK
Cohiba 4 Seater Sofa Set - Black
Item name: Cohiba 4 Seater Sofa Set - Grey

Attention! Please note that at first all screws should be inserted slightly by hand!
Turn 2-3 times so that the screw grips on its own and connects all elements loosely. The
screws must only be driven in tightly when all elements are connected with each other in
this way. Otherwise the setup won´t be possible. Only by driving them in tightly afterwards,
small deviations of the borehole or the welded joints, which always occur with
handcrafted products, can be compensated.
Notes on an optimized assembly:
Before you completely tighten the screws, check carefully all the screws and tighten them
(only) to the extent that the product remains (especially chairs or loungers) still under
load. If you are sure that your product can withstand load, place it on a solid, level
ground and put some weight on it, please carefully and always with cushions. The various
components can then align with each other. Then tighten completely the screws. Thus
you achieve and optimal alignment of the product and prevent wobbling. Don’t sit, find
Your new product was made by hand.
Slightly irregularities are rather seen as a
quality attribute than as a reason for
complaints.
Tip: Always fully insert the hex key inside
designated notch of screw.
If you don´t do that and slip out of the
screw, the screw will suffer damage and it
can caused the screw head to become
round inside you won´t be able to find
grip with the hex key anymore!
DONT’S
Don´t use this product if parts are missing, damaged
or worn down.
Don´t use any electronic tools to set up these
product. The high energy of these electronic tools
will cause screw overghten and therefor they
won’t grid.
Don´t overghten screws or bolts. Only ghten the
screws enrely aer the product is completely set
up. You shouldn’t sit or stand on it.
Don´t let your product stand in the rain. Protect it
from weather impacts. In mes of freeze and over
the winter, we suggest you to store the product in a
covered dry place.

Notice:
1. 50% Tighten before fixing all screws, Allen wrench is
recommended instead of an electric drill.
2. Place the item on a flat ground to adjust and make sure
it remains stable.
3. Tighten up all screws with tools gradually.
4. If the screws are not aligned with holes during assembly,
please loosen all the other screws to 50% and continue
the assembly process.
5. If the item is not stable, please loosen all the screws,
adjust it on a flat ground and tighten up all screws again.
6. Note : If one or some screws are fully tightened during
assembly, chances are the others will not be aligned with
holes. In addition, all the holes are designed to be relatively
larger to provide more space for the adjustment of the screws.
O
E
G
I
Q
J
K
J
K
P
F
B
N
B
C
D
A
L
M
H

AB C
Part List & Hardware
DE F
GHI
JKL
MN O
Back Frame (2 pcs ) Side Frame (4 pcs) Front Frame (2 pcs)
Seat Frame (2 pcs ) Corner Big Frame (3 pcs) Corner Small Frame (3 pcs)
Corner Seat Frame (3 pc) Corner Front Frame (3 pcs ) Corner Side Frame (3 pcs )
Table Leg Frame (2 pcs) Table Side Frame (2 pcs) Seat Cushion (2 pcs)
Corner Seat Cushion (3 pcs ) Back Pillow (2 pcs) Corner Big Back Pillow (3 pcs)

PQ 1
Part List & Hardware
23
Corner Small Back Pillow (3 pcs) Table Glass (1 pc) Bolt M6x40mm (46 pcs)
Bolt M6x30mm (42 pcs ) Allen key (1 pc)

STEP 1
Connect Seat Frame (D) & Back Frame (A) with
Bolt (1)
STEP 2
Connect part from STEP 1 & Side Frame (B)
with Bolt (1) & (2)
STEP 3 STEP 4
Put on Seat Cushion (L) & Back Pillow (N)
to complete chair
Connect part from STEP 2 & Front Frame (C)
with Bolt (1) &(2)
1
1
1
1
1
1
2
2
22
1
1
2
2
L
N
A
D
2
2
B
B
C
2 pcs
1
4 pcs
1
4 pcs
2
2 pcs
1
4 pcs
2

STEP 5
Connect Corner Small Frame (F) & Corner Seat
Frame (G) with Bolt (1)
STEP 6
Connect part from STEP 5 & Corner Big Frame (E)
with Bolt (1)
STEP 7 STEP 8
Put on Corner Seat Cushion (M), Corner Big Back
Pillow (O) & Corner Small Back Pillow (P)
to complete corner chair
Connect part from STEP 6,Corner Side Frame (I)
Corner Front Frame (H) with Bolt (1) &(2)
1
1
1
1
1
2
2
2
2
2
2
11
11
P
M
O
F
G
E
IH
2 pcs
1
1
4 pcs
1
4 pcs
1
6 pcs
2

STEP 9
Connect Table Leg Frame (J) & Table Side
Frame (K) with Bolt (2)
STEP 10
Connect part from STEP 5 & Table Leg Frame (J)
with Bolt (2)
STEP 11 STEP 12
Put on Table Glass (Q) to complete table
Connect part from STEP 6 & Table Side Frame (K)
with Bolt (2)
222
2
2
2
2
2
K
J
J
K
Q
2 pcs
2
2 pcs
2
4 pcs
2