Elkay DRKR14C Installation manual

DRKR14C
98140C (Rev. - 3/05)
Page 1
Countertop Fountains
INSTALLATION, CARE & USE MANUAL
!CAUTION
:
Reviewtheseinstructionsbeforebeginninginstallation.Besurethatinstallation
conformsto all plumbing, electrical andother applicable codes.
!
WARNING
:
When installation is complete, ensure these instructions are left in the plastic bag
providedinsidetheinstalledunitforfuturereference.
!WARNING
:
Serviceto be performed by authorizedservicepersonnelonly.
INSTALLER
NOTE: It is commonpractice to ground electrical hardware such astelephones, computers and other devices
toavailablewaterlines.This can, however, cause electricalfeedbackinthe plumbing circuit, which
results in an “electrolysis” effect occurring in the fountain. This may result in water which has a metallic
taste to it or has a noticeable increase in the metallic content of the water.
Wheninspecting plumbing circuit, remember the line may be groundedsome distance from the
installation, and may occur outside the building or area in which the unit is being installed.
This condition can be avoided (in most cases) by using recommended materials during installation.Any
drain fittings provided by theinstaller should be made of plastic whichwill electronically isolate the
fountainfromtheremainderofthe building’s plumbing circuits.

98140C (Rev. - 3/05)
DRKR14C
Page 2
1. Make 13-1/4” (337mm) diameter cutout in desired location
on countertop. Maintain the 7-5/8” (194mm) dimension
from the front edge for ADA compliance. (See Figure 1)
2. Install bubbler assembly to fountain. Align recess in
underside of bubbler with dimple in fountain.
3. Apply caulk (not provided) around cutout and waste
opening.
4. Place fountain over opening and drop in strainer.
(See Figure 2)
5. From underside, position and secure tiedown bracket
using waste fitting. (See Figure 3)
6. Use screws with nuts and washers (provided) to tighten
unit to countertop. Wipe off excess caulking.
(See Figure 3)
7. Determine required length of waste line and cut to
appropriate length. 1-1/4” O.D. waste tube furnished.
1-1/4” slip trap, waste elbow and extension not
provided.
8. Make water supply connections from service stop to the
3/8” O.D. unplated brass nipple coming out of the
bubbler. Turn on water supply and check for leaks. Newly
installed water supply line should be insulated after leak
check is completed.
9. These products are designed to operate on 20-105
PSIG supply line pressure. If the supply pressure is
above 105 PSIG, a pressure regulator must be installed
in the supply line. Any damage caused by reason of
connecting these products to supply line pressures
lower than 20 PSIG or higher than 105 PSIG is not
covered by warranty.
BUBBLERDETAIL
NOTE:
When installing replacement bubbler and pedestal, tighten
nut (Item 4) only to hold parts snug in position. Do Not
Overtighten.
Basin
Figure4-BubblerDetails
1
2
5
6
7
Figure1
Figure2
Figure3
8
9
3
10
4
11

DRKR14C
98140C (Rev. - 3/05)
Page 3
AcceptsCountertop
ThicknessUpTo1-5/8”
Figure5
Figure6

98140C (Rev. - 3/05)
DRKR14C
LK142
40322C
A54888
70012C
A54800
40089C
40048C
10031C
61313C
72460042
45675C
LK128
40038C
40619C
50074C
55000963
74080022
74080005
74080006
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Page 4
PARTSLIST
ITEMNO. PARTNO. DESCRIPTION
Bubbler Assembly
Orifice Assmbly
Screen
Nut - 3/8-18 Lock nut
Nipple - Lead Free
Nut Cover Cap
Button Cap
RetainingNut
Regulator Assembly
Metal Washer
Bubbler Body
CompleteDrain Fitting
Grid Strainer
Strainer Body
Rubber Washer
Tie Down Bracket
1/4-20 x 2-1/2 Screw
1/4-20 Hex Nut
1/4 Washer
PRINTED IN U.S.A.
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.0620
ELKAY MANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484
Figure7
See Fig. 4
13, 14
15
16 12
17
8
19
18
18
15
18 19
17
18
TROUBLESHOOTING&MAINTENANCE
OrificeAssembly: Mineraldepositson
orificecan causewaterflow tospurt ornot
regulate.Mineral depositsmaybe removedfrom
theorifice bypokingwith asmall round filenot
over1/8” diameter, orusing asmall diameter
wire.
!CAUTION
:
DO NOT file or cut orifice
material.
Stream Regulator: If orifice is clean,
regulate flow as in Step 10, Page 2 of the instal-
lationinstructions.Ifreplacement isnecessary,
seepartslistfor correctregulatorpart number.
10