Elmo Hybrid ELB-3610 User manual

ELMO Mfg. Corp. 1478 Old Countr
y
Road, Plainview, NY 11803-503
Tel.: [phone]
Fax: [phone]
Air fl
ow
ELB-3610
ELB-3610B
ELB-3610HB
Outdoor Dome housing for
ELMO PTC-200 & PTC-201C IP
PTZ cameras
"
U
U
tilit
y
lead
"
hol
ds
low
e
r
d
om
e
sec
tio
n
S
ea
l
e
d
fl
an
g
e
Blow
er
H
ea
t
er
Th
e
Bl
o
w
e
r
&
H
ea
t
e
r
confi
g
uration allows
w
a
rm
a
ir to flow on
low
e
r
d
om
e
su
rf
ace
truction prevents water droplets on the lower dome surface
Special "Rim" const
im co
e
sur
f
ac
e
ater
droplets
on
the
low
Sldfl
p
Rim
Adjustable mounting plate
Re
g
ulated out
p
ut
p
ower su
pp
l
y
gppppy
S
p
ecial "Rim" construction
p
revents water dro
p
lets on the lower dome surfac
e
ppp
Features
- Ingenious upper dome configuration prevents water
droplets on lower dome surface
- Lower dome locked in place with 4 screws with retainers
- 2 lower dome colors available
Fabrication
- UV protected black ABS construction (upper dome)
- 1/8" acrylic (lower dome)
Power Supply Specifications
Regulated output power supply
- Input : 24vac-100va when using H & B
- 24vac camera output
- 9 to 18vdc camera output, maximum 1.2amp at 70˚F
-12vdc output for Blower
- 2amp. 250V Fuse Protection
- Surge Protection
Blower Specifications
- 12vdc, 1 watt, 15cfm
- Continuous duty
Heater Board Specifications
- 24vac, 40watt Heater
- Thermostat activates at 6˚C (39˚F ± 3˚F)
- 24vac camera output
Option Heater Board
Option
Heater
Board

ELMO Mfg. Corp. 1478 Old Country Road, Plainview, NY 11803-5034
Tel.: [phone]
Fax: [phone]
45"
8"
68"
6.8"
8"
11.6"
4.3"
10.9"
12"
9.5"
7.75" 2.4"
7.8"
6.6"
4.5"
Add the following letter to Part Number for
proper lower dome color code :
C: CLEAR dome
S: SMOKED dome
C
lear
S
moked
2 lower dome colors available :
HydriD Dome Dimensions :
ECB-3610
EWB-3610
EWB-
36
1
0
E
C
B-
36
1
0
E
C
A-
36
1
0
Mounting Accessories :
EPA-
36
1
0
Part number Description Input Intensity Temperature
ELB-3610 Environmental Dome 24vac, 40 va N/A 0˚C to 30˚C (32˚F to 86˚F)
ELB-3610B Dome with Blower 24 vac, 75 va 1 watt, 15 cfm -10˚C to 49˚C (14˚F to 120˚F)
ELB-3610HB Dome with Heater & Blower 24 vac, 100 va 41 watts -30˚C to 49˚C ( -22˚F to 120˚F)
** When using a smoked dome the quality of the image may
be altered. This dome should only be used in good lighting
conditions.
- A
ccess
c
h
a
nn
e
l for
cab
l
e
- Stainless steel bolt for dome
- Waterproof
- 6" x 1" NPT threaded
p
i
pe
- Mounting box with
knockouts
- 2 Stainless Steel stra
p
s
-
F
or 3
"
to 10
"
p
o
le
- Re
q
uires EWB-361
0
- Heavy duty
eavy duty
- 4
sc
r
e
w
s
in
c
l
uded
- Requires EWB-361
0

ELMO Mfg. Corp. 1478 Old Country Road, Plainview, NY 11803-5034
Tel.: [phone]
Fax: [phone]
Installation Guide
1
¼
¼
¼
1
14
5
7
1
3
3
8
1
0
-1
1
12
2
4
9
5
6
6
5
4
3
2
1
Installation Ste
p
s for ELB-3610 series
** Do not remove immediately the plastic film on the lower dome section. Install the wall bracket (EWB-3610)
or ceiling bracket (ECB-3610). Make sure it is safely secured in place.
a) Use a Philips #1 screwdriver, release the four screws holding the lower dome to the upper dome section (see #1).
IMPORTANT: 1/4 turn counter-clockwise to unlock each screw (1).
Carefully remove the lower dome (use a light twisting movement if needed to undo).
b) Attach the upper dome section to the mounting bracket (2).
c) Remove the mounting plate (3). Pull cables through the bracket (4). Fix the camera to the mounting plate (5).
d) Connect the 24vac power cable to the "AC IN" terminals (6). Insure that the transformer isn't connected to the 120vac
source at this time (input: 24vac, 100va).
e) Connect the jumper cable (12vdc) to the camera (7), and connect RCA connector to the camera (8) when using the PTC-200
If the PTC-201C IP model is being installed, connect the communication cable to the camera (9).
f) For PTC-200, insert the mounting plate & camera assembly in location # 3 inside the dome (10).
For PTC-201C IP, insert the mounting plate & camera assembly in location # 5 inside the dome (11).
NOTE: While installing the mounting plate back in the dome, you may have to move the adapter to level the mounting plate (12).
g) Check all connections before connecting the transformer to 120vac. If the camera doesn't work, verify the fuse (13) and the
transformer ! Complete camera testing.
h) Fix the lower dome section back in
p
lace and secure the four screws. IMPORTANT: 1/4 turn clockwise to lock each screw
(
14).
Remove the
p
rotective film off the lower dome.
Optional Heater Board
d
Power Supply
pp
Outdoor Dome for ELMO
PTC-200 & PTC-201C IP
Mounting plate
n
tin
g
plateMou
n
o
n
#
l
oca
ti
o
P
re-wired
/
Do not use