Elmo QBiC S X1 User guide

START-UP GUIDE
QBiC S X1 / D1
©2013 Copyright ELMO Co., Ltd.All rights reserved.
Any names, company names and product names referred to in this guide are
trademarks or registered trademarks of the respective companies.

2
TABLE OF CONTENTS
BEFORE YOU USE....................................................................................................3
QBiC S PACKAGE CONTENTS.................................................................................4
THE NAME OF EACH PART......................................................................................5
PREPARATIONS........................................................................................................6
Installation of battery pack / Charging.....................................................................6
INSERTING microSD CARDAND WiFi CARD.......................................................7
PRECAUTIONS WHEN USING QBiC S IN THE OPENAIR..................................8
STARTING THEALERT MODE ...............................................................................10
POWERING ON....................................................................................................10
Lighting of LED while battery-powered mode is enabled......................................10
Alarm sound in battery mode................................................................................11
POWERING OFF..................................................................................................11
CHECKING THE MAINTENANCE MODE............................................................11
STARTALERT MODE (SHIFTING TOALERT MODE) ........................................12
STOPALERTING (SHIFTING TO MAINTENANCE MODE) ................................13
MAINTENANCE TOOL.............................................................................................14
ABOUT QBiC S MAINTENANCE TOOL...............................................................14
CHECK PC ENVIRONMENT................................................................................14
GETAND INSTALL THE QBiC S MAINTENANCE TOOL....................................15
UNINSTALL QBiC S MAINTENANCE TOOL........................................................15
CONNECT THIS PRODUCT TO PC VIAUSB CABLE .........................................16
CONNECTING TO WiFi ...........................................................................................17
REGISTER FOR ACCESS POINT .......................................................................17
MASS STORAGE MODE.........................................................................................18
TURNING ON THE MASS STORAGE MODE .....................................................18
UPDATE ...................................................................................................................19
IMPORTANT SAFEGUARDS...................................................................................21
BEFORE YOU USE..................................................................................................27
DISCLAIMERS.........................................................................................................31

3
BEFORE YOU USE
Thank you for purchasing QBiC S X1/D1.
This guide is intended to describe the usage and settings of the product for the
purpose of appropriate usage and the user’s safety.
Please read this guide and the “Important Safeguards” carefully before using
the product.
Please refer to the QBiC instruction manual for any other setting and
information.
Please keep this guide for future reference.
《QBiC S INSTRUCTION MANUAL》
Please download the QBiC Instruction manual from the
following QBiC Website.
QBiC Product Website: http://www.elmoqbic.com/

5
THE NAME OF EACH PART
QBiC S FRONT
QBiC S BACK
The specification in the above applies to both X1 & D1
NOTICE
Microphone
WiFi LED
Schedule LED
Key lock LED
REC LED
Alert/Alert cancel REC switch
Accessary installation port micro USB port
Lock
Reset switch
Back cover
(WiFi card slot inside)
Battery slot
Lens
WiFi switch
Schedule switch
LED lights switch
Power/Battery PWR LED
Power switch Maintenance MNT LED
LED lights

6
PREPARATIONS
INSTALLATION OF BATTERY PACK/CHARGING
*Battery pack is not inserted in the product. Battery is not fully charged at the time of
purchase. Charge the battery fully before starting to use the product.
1. The rating label which mentions product name; etc. is attached at the bottom of
the product (①). Slide 2 knobs to the opposite directions of the arrows on the
label and unlock. Slide and open the slot(②). Insert the battery pack. Slide and
close the slot. Lock the knobs.
①②
2. Turn off the product. Charging is not possible while the power is on.
3. Open the micro USB port cover. Connect the micro USB plug (smaller one) of the
supplied USB cable to the micro USB port of the product.
4. Connect the USB plug of the USB cable to a USB port on the supplied AC
adapter your PC.
5. [Power LED] on the product blinks in red while charging.
6. Battery is fully charged when [Power/LED LED] turns off.
Charging from the USB port on your PC is possible.
However, be sure to turn off the product and note that it takes longer time
to charge than when using the AC adapter.
Charging from the USB port on your PC

7
INSERTING microSD CARD AND WiFi CARD
1. Insert the supplied micro SD card in the WiFi card.
*When the WiFi card is write-protected, recording is not possible. Verify that the slide
switch is set to the unlock position. If the slide switch is set to [LOCK], slide it to
other end to release the lock.
CAUTION
Pay attention to the direction of the card when inserting the micro SD
card. Insert the microSD card until it clicks. Improper insertion of the card
may cause error.
2. To remove back cover, unlock the lock in the back cover with a flat object such as
a coin. Insert the object in ① and turn it to the direction ② indicated with an
arrow.
The back cover is removed.
3. Insert the WiFi card in the WiFi card slot.
CAUTION
Pay attention to the direction of the card when inserting the WiFi card.
Insert the WiFi card until it clicks.
Improper insertion of the card may cause error or damage the product.
Card slot
①
②
Slide switch

8
4. Close the back cover and lock it. Insert a flat object such as a coin in ① and
turn it to the direction ② indicated with an arrow.
CAUTION
Make sure to close the cover correctly and lock it tight. Insufficient
locking may deteriorate the waterproof performance and damage the
product.
PRECAUTIONS WHEN USING QBiC S IN THE OPEN AIR
Please use a commercially available outdoor housing when using this product in the
open air.
This product is guaranteed to be waterproof when the USB cover is properly installed
(USB cable is not used), but NOT guaranteed if USB cover is NOT properly installed
(USB cable is used).
And also waterproof is not guaranteed if this product is used in the open air for an
extended period of time, regardless of using the USB cover properly.
Follow the following instructions when you use the camera under water.
1. Make sure that all covers, slots and knobs are firmly closed.
USB cover
Lock
Back cover
Knobs micro USB port
Batter
y
slot
①
②

9
2. When this product is used with AC adapter, (①) remove USB cover (②) install
USB packing seal to the micro USB port (③) plug the USB cable (with USB
packing seal) connect USB cable andAC adapter, and start to use.
Use a commercially available outdoor housing if this product is used in the open
air.
CAUTION The supplied AC adapter is not waterproof.
Also the USB packing seal does not guarantee waterproof property.
3. The inside of outdoor housing may get hot or cold depending on the location of the
camera. Be sure to consult with the system installer in advance and use an extra
device such as cooling fan or heating equipment together with the outdoor
housing if necessary.
CAUTION The camera is not guaranteed to be waterproof or to be free of trouble or
damages under every condition.
Please refer to the QBiC S instruction manual for the details about use of QBiC S in
the open air.
Please download QBiC S instruction manual from the following website.
QBiC Product Website: http://www.elmoqbic.com/
①
②
③④

10
STARTING THE ALERT MODE
This product supports “Alert mode” which continuously records video and save it to
microSD card and “Maintenance mode” which configures the variety of settings and
also plays the recorded movie which is stored in the micro SD card.
In this section the following topics are covered:
[Operation of each mode] / [Indication of LEDs]
POWERING ON/OFF
POWERING ON
Press and hold (over 1second) [Power Switch] to power on the product.
[Power LED] turns blue or green.
The factory setting is “Maintenance mode”.
LIGHTING OF LED WHILE BATTERY-POWERDMODE IS ENABLED
This product supports 24-hour continuous monitoring function by the power
feeding from AC adapter.
In case the power supply is cut off, electricity is fed from the built-in battery
pack; therefore, the alert recording will be continuously operated for up to 2
hours.
At this time “Power/Battery PWR LED” turns red and it indicates that the
product is using the electricity in the built-in battery.
When “Power/Battery PWR LED” turns red, the power is not fed by AC adapter.
The product may unexpectedly turn off; so check the power conditions as soon
as you possible.
NOTICE
Turns
blue