Elo TouchSystems Wallaby KIT-EMV-VF-MX915-ING-ISC250-SQ-4 User manual

E458992 KIT-EMV-VF-MX915/M400-ING-ISC250-SQ-4

FOR USE ON:

E421137 ELO-STAND-SELF-SERVICE-15-22-COUNTERTOP4

E421325 ELO-STAND-SELF-SERVICE-15-22-FLOOR-TOP4

ASSEMBLY INSTRUCTIONS, E458992 KIT-EMV-VF-MX915/M400-ING-ISC250-SQ-4

Revision AQIG600186

Contents for

Kit:

EMV Arm Assembly

Qty. 1

Screws

Bag CQty.2 SCREW, M3X8, PAN-HEAD,

CROSS-RECESS

Bag RQty. 4 SCREW, M4X6, FLAT-HEAD,

CROSS-RECESS

Bag PQty.8 SCREW, M4X5, PAN-HEAD,

CROSS-RECESS

Bag GQty. 3 SCREW_M4X10_SPECIAL

PAN-HEAD, CROSS-RECESS

Bag HQty. 3 SCREW_M3X8_SPECIAL

PAN-HEAD, CROSS-RECESS

Bag QQty. 1 SCREW_1/4”x5/16”,

PAN-HEAD, CROSS-RECESS

EMV Edge Bracket, 22 Android

2.0/3.0

(bag label “22 A”)

Qty. 1

EMV Mount Plate, Long

Qty. 1

Tie-wrap

Qty. 2

ASSEMBLY INSTRUCTIONS, E458992 KIT-EMV-VF-MX915/M400-ING-ISC250-SQ-4

EMV Edge Bracket, 15

Android (bag label “15 A”)

Qty. 1

EMV Edge Bracket, 22 Windows

(bag label “22 W”)

Qty. 1

EMV Edge Bracket, 15 Windows

(bag label “15 W”)

Qty. 1

EMV Edge Bracket, 22 Android 4.0

(bag label “22 A4”)

Qty. 1

Remove Fill Plate on Display Bracket.

Add the EMV Mount Plate to the

Display Bracket using (4) screws from

bag “R”.

Assemble EMV Arm to Display Bracket. Add

(2) screws from bag “P” at right most

position “A” to secure EMV Arm to Display

Bracket.

Add (2) screws to EMV Mount Plate from bag “P”

at position 1, 2,3 or 4. Leave ~3mm (1/8”) gap (for

EMV Arm).

Position “1” for 15” in portrait.

Position “2” for 22” in portrait.

Position “3” for 15” in landscape.

Position “4” for 22” in landscape.

1234

Route EMV terminal

cable and tie-wrap.

For Square Terminal, skip to step 7.

Remove and save EMV Cover Plate and screws.

Add (3) screws for mounting EMV terminal:

-Use bag “G” and holes labeled “1” for Ingenico iSC250

-Use bag ”H” and holes labeled “2” for Verifone MX915

-Use bag ”H” and holes labeled “3” for Verifone M400

Attach EMV terminal cable to terminal and slide terminal

onto (3) Arm Assembly screws.

Cover Plate Attach EMV Cover Plate

and screws.

Skip to step 11

For Square Terminal, skip to step 7.

Remove and discard EMV Cover Plate and M4 screws.

Remove and save Base Plate and M3 screws.

Cover Plate

From Bag “Q”

Base Plate

Attach Square Terminal using (1) screw from bag “Q”,

threading screw into hole on bottom of Square Terminal.

Assemble (3) screws from bag “H” as shown to prevent

Square Terminal from rotating. Tighten each screw until

resistance is felt.

From Bag “H”

Route EMV terminal

cable and tie-wrap.

109

Reinstall Base Plate to arm using M3 screws from step 7.

Remove plastic cover from right edge of display.

Add Edge Bracket using (2) screws from bag “C”.

Use Edge Bracket “15 A” for Android 15”

Use Edge Bracket “22 A” for Android 22” 2.0/3.0

Use Edge Bracket “22 A4” for Android 22” 4.0

Use Edge Bracket “15 W” for Windows 15”

Use Edge Bracket “22 W” for Windows 22”

Return to Wallaby™assembly instructions

(QIG600184/QIG600185) to complete installation.

The information in this document is subject to change without notice. Elo Touch Solutions, Inc. and its Affiliates (collectively “Elo”) makes no representations or warranties with respect to

the contents herein, and specifically disclaims any implied warranties of merchantability or fitness for a particular purpose. Elo reserves the right to revise this publication and to make

changes from time to time in the content hereof without obligation of Elo to notify any person of such revisions or changes.

No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means,

including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of Elo Touch Solutions, Inc.