Elo TouchSystems WALLABY PRO User manual

© Copyright 2022 Elo Touch Solutions, Inc. 1
ASSEMBLY INSTRUCTIONS, WALLABYTM PRO FLOOR STAND
Revision AUM600658

© Copyright 2022 Elo Touch Solutions, Inc. 2
Contents for Kits: E989314 / E534462, Wallaby Pro Self-Service Floor Stand Top
Printer Door (ADA) Bag
Qty.1 Printer Door (ADA)
Qty.4 Screw, M3x6, Pan Head, Cross
Recess, Black
Cables
Qty.3 Cable, 0.3m IEC C13 to IEC C14
Qty.3 Cable, 0.3m IEC C5 to IEC C14
Qty.1 Cable, 4.5m IEC C13 to NA (E989314 only)
Qty.1 Cable, 5.0m IEC C13 to EU (E989314 only)
Qty.1 Cable, 5.0m IEC C13 to UK (E989314 only)
Qty.2 Cable, SMA Extension, 18”
Qty.1 Cable, 0.35m ECMG4 to C14
Stand
Qty. 1
ECMG4 Bracket Bag
Qty.1 ECMG4 Bracket
Printer Hardware Bag
Qty. 1 Printer Bracket 3
Qty. 1 Printer Bracket 4
Qty. 1 Printer Chute 2
Qty. 1 Printer Chute 3
Qty. 1 Printer Chute 4
Qty. 1 Printer Filler
Printer Screws-
Length 6mm
Qty.
4
Screw, T3x6, Pan
Head, Cross
Recess,
Sheetmetal type,
Black
Printer Screws-
Length 12mm
Qty.
2
Screw, T3x12, Pan
Head, Cross
Recess,
Sheetmetal type,
Black
VESA Spacer and Screws Bag
Qty. 1 VESA Spacer
Qty.4 Screw, M4x6, Pan Head,
Cross Recess, Black
VESA Screws-
Length 14 Qty.4 Screw, M4x14, Flat Head,
Cross Recess, Black
VESA Screws-
Length 18 Qty.4 Screw, M4x18, Flat Head,
Cross Recess, Black
VESA Screws-
Length 22 Qty.4 Screw, M4x22, Flat Head,
Cross Recess, Black
Cable tie,
Medium
Qty. 15
Android Backpack Screws Bag
Qty.4 Screws, M4x27, Flat Head, Cross
Recess, Black
Cable tie, Large
Qty. 2
(E534462 only)

© Copyright 2022 Elo Touch Solutions, Inc. 3
Contents for Kit: E989512, Wallaby Pro Self-Service Floor Stand Base
Floor Base
Qty. 1
Mounting Screws Bag
Qty.8 Screw, M5x15, Socket Head, Custom,
Stainless
Qty.4 Screw, M5x10, Flat Head, Cross
Recess, Black
Wheel Kit Bag
Qty.2 Wheel Assembly
Qty.6 Screw, M5x6, Flat Head, Cross
Recess, Black
L-Key
Qty. 1

© Copyright 2022 Elo Touch Solutions, Inc. 4
Contents for Kit: E989705, Wallaby Pro Self-Service Floor Stand Double Base
Double Floor Base
Qty. 1
Base Mounting Screws Bag
Qty.8 Screw, M5x15, Socket Head, Custom,
Stainless
Qty.8 Screw, M5x10, Flat Head, Cross
Recess, Black
Spacer Screws Bag
Qty.16 Screw, M4x10, Flat Head, Cross
Recess, Black
Spacer
Qty. 2
Upper Mounting Screws Bag
Qty.2 Screw, M5x22, Socket Head, Black
L-Key
Qty. 1

© Copyright 2022 Elo Touch Solutions, Inc. 5
Contents for Kit:
E990854, Backer Board for Wallaby Pro Stands
Hardware
Qty.8 Screw, M4x12, Pan Head, Cross-
Recess, Zinc
Qty.8 Washer, M4, Zinc
Backer Board
Qty. 1
Contents for Kit:
E990151, Backer Board for Wallaby Pro Double-Sided Floor Stands
Backer Board
Qty. 1

© Copyright 2022 Elo Touch Solutions, Inc. 6
Remove lower front panel by removing two side screws.
Tilt out, lift up and remove panel.
If installing wheel kit, attach wheels to base plate (P/N E989512).
Flip base plate over. Slide wheels onto back edge of base
plate, then fasten using six screws from “Wheel Kit” bag.
12
Single-Sided Install
(For Double-Sided Installs, skip to step 6)
Caution: While tilting the stand onto or off the
wheels, support base plate with one foot to
prevent rollback.

© Copyright 2022 Elo Touch Solutions, Inc. 7
Install stand to base plate as shown. Fasten by installing
twelve screws from “Base Mounting Screws” bag. Use L-
Key included with stand to tighten socket head screws.
Level base plate by adjusting feet (turning it counter-
clockwise lowers the foot, turning it clockwise raises the
foot).
Install backer board (P/N E990854) to stand by removing eight screws
on back cover (discard screws and back cover) and installing backer
board with screws and washers included with backer board.
34Backer Board Install (Optional)

© Copyright 2022 Elo Touch Solutions, Inc. 8
Unscrew display door thumbscrews. Open door and engage prop in
hole.
5
Skip to step 12
6
Remove lower front panel from 1st stand by removing two
side screws. Tilt out, lift up and remove panel. Repeat on
2nd stand.
Double-Sided Install

© Copyright 2022 Elo Touch Solutions, Inc. 9
Install 1st stand to double base plate (P/N E989705) as shown. Fasten
by installing eight screws from “Base Mounting Screws” bag. Use L-Key
included with stand to tighten socket head screws. Level double base
plate by adjusting feet (turning it counter-clockwise lowers the foot,
turning it clockwise raises the foot).
78
Install one spacer (included with double base) onto each
stand by removing eight screws on back cover (discard back
cover) and installing spacer using the same screws. Both
spacers (1 per stand) are required if no backer board is
used.
For optional backer board (P/N E990151), discard one
spacer and use backer board in place of one of the spacers.

© Copyright 2022 Elo Touch Solutions, Inc. 10
Unscrew display door thumbscrews on 1st stand. Open door
and engage props in hole. Repeat on 2nd stand.
9
Install 2nd stand to double base plate as shown. Fasten by
installing eight screws from “Base Mounting Screws” bag.
Use L-Key included with stand to tighten socket head
screws.
10