elock ADNIL User manual

V.EPIR-A03052008
Passive Infrared Detector
With Pet Immunity
•ADNIL passive infrared detector by means of dual element
(model EPIR-A) or quad element (model EPIR-B)
pyroelectric sensor immune to the temperature changes.
•Employs optically coupled MOSFET technology switches
with super efficiency (only available for EPIR-A11 or B11).
•High immunity against false alarms and electro-magnetic
fields.
•Manually adjustable sensibility, temperature compensation
of alarm threshold for proper functioning in environments
with notable temperature changes.
•Offers exceptional level of detection capability and stability
for trouble-free installation.
•EPIR-A10 – Duo element detector with pet immunity and coil
relay
•EPIR-A11 – Duo element detector with pet immunity and
solid-state relay
•EPIR-B10 – Quad element detector with pet immunity and
coil relay
•EPIR-B11 – Quad element detector with pet immunity and
solid-state relay
Infrared sensor Dual element (EPIR-A)
Quad element (EPIR-B)
Input voltage 9 ~ 16VDC, 12V
(Recommended)
Current consumption
Standby ~9mA; Alarm
~38mA (Relay)
10-12mA (Solid -state)
Solid-state alarm output 100mA, N.C only
Coil relay alarm output 2A, N.C / N.O selectable
Alarm period Approximately 1 second
Tamper switch N.C
LED indicator Red, can be disabled
Detectable speed 0.3 ~ 1m/sec
Dimension 117 x 66 x 45 mm
Unit weight 94g (EPIR-A10, B10)
90g (EPIR-A11, B11)
Operating temperature -20°C ~ 60°C or
-4°F ~ 140°F
Avoid common false alarm sources specially DO NOT run
cables parallel to AC main wires!!!
1 Cable knockout access
2 Terminal block
3 N.C / N.O jumper
4 LED ON / OFF jumper
5 LED
6 Tamper switch
7 Mounting setting
8 Infrared sensor (DO NOT TOUCH!)
9 Sensitivity adjustment jumper
10 Corner knockout
ADNIL
DESCRIPTION
SPECIFICATION
FAMILY MODELS
INSTALLATION HINT
www.elock2u.com
Avoid installing the detector facing
directly or reflected by sunlight, car
head lights, or bright surfaces such as
mirror and windows.
Avoid mounting the detector above air
vents, lamps, or equipment that may
change the environment temperature
rapidly. These areas can radiate or
direct heat over to cause nuisance
tripping.
Mount the detector on a stable surface
to prevent nuisance tripping caused by
the vibration.
Ensure that there are no obstructions
such as furniture, plants in the field of
view, which may create a blind spot of
the detector.
Detection is most effective when the
movement is “across” the detection
zones rather than “toward” the
detector.
PARTS IDENTIFICATION

V.EPIR-A03052008
10
1. Open the top cover by loosing the screw at the bottom of
the unit as shown at A.
2. Mounting the wall bracket onto the wall at height of 2m
with screws as shown at B.
3. Insert the ball bracket (C) into the bottom back plate of the
unit and tighten up with screws.
4. Connect the signal cables to the corresponding terminal
accordingly.
0V, 12V : 9 ~ 16 VDC, 12VDC recommended
ALARM : Zone input for alarm panel (N.C/N.O)
TAMPER : N.C loop for alarm panel
5. Insert the all unit after refit the top cover onto the wall
bracket.
6. There are 6 knockouts provided for the wall mounting
without the bracket. Ignore step 2 and 3 if installation
without using wall bracket.
7. Remove the PCB from the base. Mount the base on the
wall with selected position with at least 2 screws after
remove the knockouts (D).
8. Refit the PCB onto the base and replace the top cover,
apply the power supply to the detector and conduct a walk
test.
Wait approximate 1.5 minutes after applying 12VDC power for
the warm up and stabilize time. Conduct a testing with the
protected area cleared of all people. Walk test should be
conducted at least once a year to confirm proper operation and
coverage of the detector.
1. Wait until the LED is off.
2. Walk across the detection zones with a normal speed.
3. The LED will turn on whenever it detects a movement.
4. Allow 8-11 seconds between each test for the detector to
stabilize.
5. The LED display can be disabled by pulling off the jumper
at location J2 labeled as “ON/OFF”.
Use the sensitivity adjustment jumper (JP1) to select high / low
sensitivity. Placing on the jumper cap indicates HIGH
sensitivity selection; remove the cap for LOW sensitivity
selection.
The Pet Immunity system is being embedded into the board,
which is set to factory default setting.
2
1
WALK TEST
SENSITIV
I
TY ADJUSTMENT
INSTALLATION INSTRUCTION
B
A
D
PET IMMUNITY
C
MOUNTING SETTIN
G
COVERAGE PATTERN
ICT at work!
3
4
5
6
7
8
9